Siemens FDM275 User manual

FDM275, FDM275(F)
Radio manual call point
Technical Manual
A6V10401120_g_en_-- Smart Infrastructure
2020-03-31

Imprint
Technical specifications and availability subject to change without notice.
Transmittal, reproduction, dissemination and/or editing of this document as well as
utilization of its contents and communication thereof to others without express
authorization are prohibited. Offenders will be held liable for payment of damages.
All rights created by patent grant or registration of a utility model or design patent
are reserved.
Issued by:
Siemens Switzerland Ltd.
Smart Infrastructure
Global Headquarters
Theilerstrasse 1a
CH-6300 Zug
Tel. [phone]
www.siemens.com/buildingtechnologies
Edition: 2020-03-31
Document ID: A6V10401120_g_en_--
© Siemens Switzerland Ltd, 2014
Imprint
2 | 46 A6V10401120_g_en_--

A6V10401120_g_en_-- 3 | 46
Table of contents
1 About this document................................................................................. 5
1.1 Applicable documents .............................................................................. 7
1.2 Download center....................................................................................... 7
1.3 Technical terms and abbreviations........................................................... 7
1.4 Revision history ........................................................................................ 8
2 Safety ....................................................................................................... 9
2.1 Safety notes.............................................................................................. 9
2.2 Safety regulations for the method of operation......................................... 10
2.3 Standards and directives complied with ................................................... 12
2.4 Release Notes .......................................................................................... 12
3 Structure and function .............................................................................. 13
3.1 Overview................................................................................................... 13
3.1.1 Scope of delivery ........................................................................ 14
3.1.2 Details for ordering ..................................................................... 14
3.1.3 Product versionES ..................................................................... 15
3.1.4 Power supply .............................................................................. 16
3.2 Setup ........................................................................................................ 17
3.3 Function.................................................................................................... 18
3.3.1 Danger levels .............................................................................. 18
3.3.2 Internal alarm indicator ............................................................... 18
3.3.3 Test mode ................................................................................... 20
3.3.4 Alarm activation .......................................................................... 20
3.3.5 Diagnosis levels .......................................................................... 20
3.3.6 Degraded mode in the FDnet/C-NET ......................................... 21
3.3.7 Interface to service devices ........................................................ 21
3.4 Accessories .............................................................................................. 22
3.4.1 Battery pack BAT3.6-10.............................................................. 22
3.4.2 MCL-USB (radio) adapter FDUZ227 .......................................... 22
3.4.3 Protective cover FDMC295......................................................... 23
3.4.4 Glass inserts FDMG295-x .......................................................... 23
3.4.5 Plastic inserts FDMP295-x ......................................................... 23
3.4.6 Key FDMK295 ............................................................................ 24
4 Planning.................................................................................................... 25
4.1 Compatibility FDnet/C-NET ...................................................................... 25
4.2 Fields of application.................................................................................. 25
4.3 Mounting site ............................................................................................ 25
4.4 Environmental influences ......................................................................... 25
5 Mounting and installation.......................................................................... 26
5.1 Mounting radio manual call point FDM275 ............................................... 26
5.2 Installation ................................................................................................ 27
5.3 Replacing the plastic insert with a glass insert ......................................... 30
5.4 Installing the protective cover ................................................................... 31
6 Commissioning ......................................................................................... 32
6.1 Performance check................................................................................... 32
6.2 Localization and device testing................................................................. 33

4 | 46 A6V10401120_g_en_--
7 Maintenance / Repair ............................................................................... 34
7.1 State of operational readiness after alarm activation ............................... 34
7.2 Establishing factory settings ..................................................................... 36
7.3 Basic principles for replacing the battery pack ......................................... 38
7.4 Replacing the battery pack in the radio manual call point ........................ 39
8 Specifications ........................................................................................... 41
8.1 Technical data .......................................................................................... 41
8.2 Dimensions............................................................................................... 43
8.3 Master gauge for recesses ....................................................................... 43
8.4 Environmental compatibility and disposal................................................. 43
Glossary ............................................................................................................. 44
Index................................................................................................................... 45

1 About this document
Goal and purpose
This document contains all information on the radio manual call point FDM275.
Following the instructions consistently will ensure that the product can be used
safely and without any problems.
Intended use
The radio manual call pointsFDM275 and FDM275(F) may only be used together
with a radio gatewayFDCW241 in a fire detection system FS20/FS720.
Target groups
The information in this document is intended for the following target groups:
Target group Activity Qualification
Product Manager ● Is responsible for information
passing between the manufacturer
and regional company.
● Coordinates the flow of information
between the individual groups of
people involved in a project.
● Has obtained suitable specialist
training for the function and for the
products.
● Has attended the training courses
for Product Managers.
Project Manager ● Coordinates the deployment of all
persons and resources involved in
the project according to schedule.
● Provides the information required to
run the project.
● Has obtained suitable specialist
training for the function and for the
products.
● Has attended the training courses
for Project Managers.
Project engineer ● Sets parameters for product
depending on specific national and/
or customer requirements.
● Checks operability and approves
the product for commissioning at
the place of installation.
● Is responsible for troubleshooting.
● Has obtained suitable specialist
training for the function and for the
products.
● Has attended the training courses
for Product Engineer.
Installation personnel ● Assembles and installs the product
components at the place of
installation.
● Carries out a function check
following installation.
● Has received specialist training in
the area of building installation
technology or electrical installations.
Commissioning personnel ● Configures the product at the place
of installation according to
customer-specific requirements.
● Checks the product operability and
releases the product for use by the
operator.
● Searches for and corrects
malfunctions.
● Has obtained suitable specialist
training for the function and for the
products.
● Has attended the training courses
for commissioning personnel.
Maintenance personnel ● Carries out all maintenance work.
● Checks that the products are in
perfect working order.
● Searches for and corrects
malfunctions.
● Has obtained suitable specialist
training for the function and for the
products.
Document identification
The document ID is structured as follows:
About this document 1
A6V10401120_g_en_-- 5 | 46

ID code Examples
ID_ModificationIndex_Language_COUNTRY
-- = multilingual or international
A6V10215123_a_de_DE
A6V10215123_a_en_--
A6V10315123_a_--_--
Date format
The date format in the document corresponds to the recommendation of
international standard ISO8601 (format YYYY-MM-DD).
Conventions for text marking
Markups
Special markups are shown in this document as follows:
⊳ Requirement for a behavior instruction
1.
2.
Behavior instruction with at least two operation sequences
– Version, option, or detailed information for a behavior instruction
⇨ Intermediate result of a behavior instruction
⇨ End result of a behavior instruction
● Numbered lists and behavior instructions with an operation
sequence
[➙ X] Reference to a page number
'Text' Quotation, reproduced identically
<Key> Identification of keys
> Relation sign and for identification between steps in a sequence,
e.g., 'Menu bar' > 'Help' > 'Help topics'
↑Text Identification of a glossary entry
Supplementary information and tips
The 'i' symbol identifies supplementary information and tips for an easier way of
working.
FDM275 will now apply to both variants of the radio manual call point – FDM275
and FDM275(F).
About this document
1
6 | 46 A6V10401120_g_en_--

1.1 Applicable documents
Document ID Title
008331 List of compatibility (for 'Sinteso™' product line)
A6V10227631 Planning Radio fire detection system SWING
A6V10227639 Technical manual Radio gateway FDCW241
A6V10227643 User Guide SWING-Tool FXS2061
A6V10229261 List of compatibility (for 'Cerberus™ PRO' product line)
A6V10271323 Data sheet SWING Neural radio fire detector FDCW241,
FDOOT271, FDM273, FDM275, FDM275(F)
A6V10367669 Open-Source Software (OSS) Licenses SWING
A6V10401114 Installation Radio manual call point FDM275, FDM275(F)
1.2 Download center
You can download various types of documents, such as data sheets, installation
instructions, and license texts via the following Internet address:
https://siemens.com/bt/download
lEnter the document ID in the search field.
You will also find information about search variants and links to mobile
applications (apps) for various systems on the home page.
1.3 Technical terms and abbreviations
Term Explanation
AI Alarm indicator
Battery empty Fault message in the event of a battery failing completely
Battery low Fault message in the event that the spare battery is activated
FDnet/C-NET Addressed detector line
IAI Internal alarm indicator
LED Light-emitting diode
About this document
Applicable documents 1
A6V10401120_g_en_-- 7 | 46

1.4 Revision history
The reference document's version applies to all languages into which the reference
document is translated.
The first edition of a language version or a country variant may, for example, be
version 'd' instead of 'a' if the reference document is already this version.
The table below shows this document's revision history:
Version Edition date Brief description
g 2020-03-31 ● 'Technical data' chapter: 'Radio: Transmitting power, frequency range,
footnote' paragraph updated
● Editorial changes
f 2018-11-19 ● Editorial changes
e 2016-11-28 ● Frequencies specified in 'Technical data' chapter
d 2016-09-30 Changes/additions in the following chapters:
● Replacing the plastic insert with a glass insert
● Editorial changes
c 2015-10-15 Changes/additions in the following chapters:
● Compatibility FDnet/C-NET
● Installation
● Technical data
b 2015-04-01 ● Editorial changes
● Flashing behavior table added
a 2014-02-01 First edition
About this document
Revision history
1
8 | 46 A6V10401120_g_en_--

2 Safety
2.1 Safety notes
Comply with the following safety notes to protect life, limb, and property.
The safety notes in the document include the following elements:
● Symbol for hazard
● Signal word
● Type and source of hazard
● Consequences in the event the hazard occurs
● Measures or prohibitions to prevent the hazard
Symbol for hazard
This is the symbol for hazard. It warns you of Risks of injury.
Comply with all measures designated by this symbol to prevent injury or
death.
Additional hazard symbols
These symbols indicate general hazards, type of hazard, possible consequences,
measures and prohibitions, a sample of which is displayed in the following table:
General hazard Potentially explosive
atmospheres
Voltage/electrical shock Laser light
Battery Heat
Signal word
The signal word classifies the hazard as defined in the following table:
Signal word Danger level
DANGER 'DANGER' identifies a dangerous situation, that results directly in death or serious
injuries, if you do not avoid this situation.
WARNING 'WARNING' identifies a dangerous situation, that can result in death or serious
injuries, if you do not avoid this situation.
CAUTION 'CAUTION' identifies a dangerous situation, that can result in minor or moderate
injuries, if you do not avoid this situation.
Note ' NOTE ' identifies a possible situation that may cause damage if not observed.
' NOTE ' does not reference possible injury.
Depiction of risk of injury
Notes on risk of injury is depicted as follows:
WARNING
Type and source of hazard
Consequences in the event the hazard occurs
● Measures/prohibitions to prevent the hazard
Safety
Safety notes 2
A6V10401120_g_en_-- 9 | 46

DEPICTION for possible damage to property
Notes on possible damage to property is depicted as follows:
NOTICE
Type and source of hazard
Consequences in the event the hazard occurs
● Measures/prohibitions to prevent the hazard
2.2 Safety regulations for the method of operation
National standards, regulations and legislation
Siemens products are developed and produced in compliance with the relevant
European and international safety standards. Should additional national or local
safety standards or legislation concerning the planning, mounting, installation,
operation or disposal of the product apply at the place of operation, then these
must also be taken into account together with the safety regulations in the product
documentation.
Electrical installations
WARNING
Electrical voltage
Electric shock
● Work on electrical installations may only be carried out by qualified
electricians or by instructed persons working under the guidance and
supervision of a qualified electrician, in accordance with the electrotechnical
regulations.
● Wherever possible disconnect products from the power supply when carrying
out commissioning, maintenance or repair work on them.
● Lock volt-free areas to prevent them being switched back on again by mistake.
● Label the connection terminals with external voltage using a
'DANGERExternal voltage' sign.
● Route mains connections to products separately and fuse them with their own,
clearly marked fuse.
● Fit an easily accessible disconnecting device in accordance with IEC60950‑1
outside the installation.
● Produce earthing as stated in local safety regulations.
CAUTION
Noncompliance with the following safety regulations
Risk of injury to persons and damage to property
● Compliance with the following regulations is required.
● Specialist electrical engineering knowledge is required for installation.
● Only an expert is permitted to carry out installation work.
Incorrect installation can take safety devices out of operation unbeknown to a
layperson.
Safety
Safety regulations for the method of operation
2
10 | 46 A6V10401120_g_en_--

Mounting, installation, commissioning and maintenance
● If you require tools such as a ladder, these must be safe and must be intended
for the work in hand.
● When starting the fire control panel ensure that unstable conditions cannot
arise.
● Ensure that all points listed in the 'Testing the product operability' section below
are observed.
● You may only set controls to normal function when the product operability has
been completely tested and the system has been handed over to the customer.
Testing the product operability
● Prevent the remote transmission from triggering erroneously.
● If testing building installations or activating devices from third-party companies,
you must collaborate with the people appointed.
● The activation of fire control installations for test purposes must not cause
injury to anyone or damage to the building installations. The following
instructions must be observed:
– Use the correct potential for activation; this is generally the potential of the
building installation.
– Only check controls up to the interface (relay with blocking option).
– Make sure that only the controls to be tested are activated.
● Inform people before testing the alarm devices and allow for possible panic
responses.
● Inform people about any noise or mist which may be produced.
● Before testing the remote transmission, inform the corresponding alarm and
fault signal receiving stations.
Modifications to the system design and the products
Modifications to the system and to individual products may lead to faults,
malfunctioning and safety risks. Written confirmation must be obtained from
Siemens and the corresponding safety bodies for modifications or additions.
Modules and spare parts
● Components and spare parts must comply with the technical specifications
defined by Siemens. Only use products specified or recommended by
Siemens.
● Only use fuses with the specified fuse characteristics.
● Wrong battery types and improper battery changing lead to a risk of explosion.
Only use the same battery type or an equivalent battery type recommended by
Siemens.
● Batteries must be disposed of in an environmentally friendly manner. Observe
national guidelines and regulations.
Disregard of the safety regulations
Before they are delivered, Siemens products are tested to ensure they function
correctly when used properly. Siemens disclaims all liability for damage or injuries
caused by the incorrect application of the instructions or the disregard of danger
warnings contained in the documentation. This applies in particular to the following
damage:
● Personal injuries or damage to property caused by improper use and incorrect
application
● Personal injuries or damage to property caused by disregarding safety
instructions in the documentation or on the product
● Personal injury or damage to property caused by poor maintenance or lack of
maintenance
Safety
Safety regulations for the method of operation 2
A6V10401120_g_en_-- 11 | 46

2.3 Standards and directives complied with
A list of the standards and directives complied with is available from your Siemens
contact.
2.4 Release Notes
Limitations to the configuration or use of devices in a fire detection installation with
a particular firmware version are possible.
WARNING
Limited or non-existent fire detection
Personal injury and damage to property in the event of a fire.
● Read the 'Release Notes' before you plan and/or configure a fire detection
installation.
● Read the 'Release Notes' before you carry out a firmware update to a fire
detection installation.
NOTICE
Incorrect planning and/or configuration
Important standards and specifications are not satisfied.
Fire detection installation is not accepted for commissioning.
Additional expense resulting from necessary new planning and/or configuration.
● Read the 'Release Notes' before you plan and/or configure a fire detection
installation.
● Read the 'Release Notes' before you carry out a firmware update to a fire
detection installation.
Safety
Standards and directives complied with
2
12 | 46 A6V10401120_g_en_--

3 Structure and function
3.1 Overview
The manual call point FDM275 is intended for use in areas of a building where a
fire can be detected by people who can manually trigger an alarm.
The manual call point FDM275 consists of a back box, a switching unit, and a
battery pack. The manual call point FDM275 has the following features:
● Manual call points with direct activation
– Alarm activation by pressing the pressure point
● Radio communication with:
– Radio gateway
– Other radio devices
● Individual detector addressing
● Alarm indicator with status display (green and red):
– Identifies alarm
– Confirms contact with the radio network
– Confirms detector test
● Battery operation
● Versions with resettable plastic or glass insert
● Surface mounting
● Key for resetting the alarm after alarm activation and for opening the housing
Structure and function
Overview 3
A6V10401120_g_en_-- 13 | 46

3.1.1 Scope of delivery
The radio manual call point FDM275 is supplied with a mounted plastic insert
'Neutral' FDMG295 and key FDMK295, and without a battery pack.
The following items must be ordered separately:
● Battery pack BAT3.6-10
● Glass insert 'Neutral'
● Plastic insert for 'France'
● Glass insert for 'France'
3.1.2 Details for ordering
Type Order no. Designation
FDM275 S54323-F105-A1 Radio manual call point with plastic insert
'Neutral' FDMP295
FDM275(F) S54323-F105-A2 Radio manual call point with plastic insert
for 'France'
BAT3.6-10 S54370-Z11-A1 Battery pack [➙22]
Accessories:
FDMC295 A5Q00013440 Protective cover [➙23]
FDMG295 A5Q00013442 Glass insert 'Neutral' [➙23]
FDMG295-F A5Q00013443 Glass insert for 'France' [➙23]
FDMP295 A5Q00013445 Plastic insert 'Neutral' [➙23]
FDMP295-F A5Q00013446 Plastic insert for 'France' [➙23]
FDMK295 A5Q00013448 Key [➙24]
Structure and function
Overview
3
14 | 46 A6V10401120_g_en_--

3.1.3 Product versionES
The product version ES provides the technical status of a device in terms of
software and hardware. The product version is provided as a two-digit number.
You will find the details of your device's product version:
● On the packaging label
● On the product label or the type plate
Product version on the packaging label
Details of the product version can be found directly on the packaging label in the
barcode:
ES
Figure 1: Example of a packaging label with details of the product version
Product version on the product label and the type plate
Details of the product version can be found after the device order number:
ES
04
Figure 2: Example of a product label with details of the product version
Depending on the product and various approvals, the product labels may differ in
terms of the information type and layout.
Look for your device's order number on the product label.
You will find the product version after the order number.
Structure and function
Overview 3
A6V10401120_g_en_-- 15 | 46

3.1.4 Power supply
The battery pack BAT3.6-10 supplies the radio devices with power. The battery
pack consists of lithium batteries plus a battery cable and a battery connector.
1
2
3
4
Figure 3: Battery pack BAT3.6-10
1 Battery pack consisting of:
● 4lithium batteries for normal operation
● 1lithium battery as a spare in the case of 'Battery low' operation
2 Label with area for filling in the commissioning date
3 Battery cable
4 Battery connector with protection against polarity reversal
● In normal operation: Can be used for the service life stated
● In 'Battery low' operation: subject to reduced operating life
● Connections cannot be reversed thanks to battery connector with protection
against polarity reversal
Structure and function
Overview
3
16 | 46 A6V10401120_g_en_--

3.2 Setup
180°
5
9
1
2
3
4
5
7
8
10
11
13
12
14
6
Figure 4: Radio manual call point FDM275
1 Back box 8 Plastic/glass insert
2 Screws for wall mounting19 Pressure point marking
3 Battery connector 10 Housing cover
4 Battery pack BAT3.6-10111 Key
5 Switching unit 12 Connection for battery connector
6 Internal alarm indicator 13 Housing switching contact
7 Screws for switching unit 14 'new' opening with button
1 Not included in the scope of delivery
Structure and function
Setup 3
A6V10401120_g_en_-- 17 | 46

3.3 Function
3.3.1 Danger levels
The radio manual call point can transmit the following danger levels to the control
panel:
Danger level Meaning
0 Normal state, no danger
3 Alarm
The evaluation of the danger level and the resulting measures (e.g.activation of
remote transmission) are configured on the control panel.
3.3.2 Internal alarm indicator
The internal alarm indicator's LED has two colors and shows the operating
condition of the radio manual call point FDM275.
Figure 5: Internal alarm indicator
The table below describes the flashing behavior of the internal alarm indicator in
the radio manual call point FDM275:
Several flashing patterns are available for normal operation. The flashing pattern
is selected using the software 'FXS2002'.
Operating condition Flashing
mode
Graphic
Alarm IAI flashes
red once a
second
t
0 1 2 3 4 5 6 7 8 9 10 1211 [s]
Alarm in test mode IAI flashes
green twice
every
fourseconds
and red every
second in-
between
t
0 1 2 3 4 5 6 7 8 9 10 1211 [s]
Fault There is an error. IAI flashes
red four times
every second
t
0 1 2 3 4 5 6 7 8 9 10 1211 [s]
Structure and function
Function
3
18 | 46 A6V10401120_g_en_--

Operating condition Flashing
mode
Graphic
Commissionin
g
The radio manual call
point has not yet been
logged on to a radio
gateway
And
The radio manual call
point is not mounted in
the back box.
And
There is no contact
with the radio network.
IAI flashes
red once
every two
seconds
t
0 1 2 3 4 5 6 7 8 9 10 1211 [s]
The radio manual call
point has already been
logged on to a radio
gateway
And
The radio manual call
point is not mounted in
the back box.
And
There is no contact
with the radio network.
IAI flashes
green once
every two
seconds
t
0 1 2 3 4 5 6 7 8 9 10 1211 [s]
The radio manual call
point is mounted in the
back box but has not
been logged on to the
radio network.
IAI flashes
green twice
every two
seconds
t
0 1 2 3 4 5 6 7 8 9 10 1211 [s]
Normal Configuration 1 IAI flashes
green once
every 30
seconds
t
0 1 2 3 4 5 6 7 8 9 3130 [s]
Configuration 2 IAI off
t
0 1 2 3 4 5 6 7 8 9 10 1211 [s]
Test IAI flashes
green twice
every four
seconds
t
0 1 2 3 4 5 6 7 8 9 10 1211 [s]
New battery IAI lights up
once for five
seconds
t
0 1 2 3 4 5 6 7 8 9 10 1211 [s]
x1
Battery is flat IAI off
t
0 1 2 3 4 5 6 7 8 9 10 1211 [s]
Several operating conditions may be indicated at the same time. This may lead to
the flashing patterns overlapping one another. The red LED indicator has priority
over the green LED indicator.
Flashing patterns with a higher frequency will overlap those with a lower
frequency, which means that the latter may no longer be discernible.
Not all fire control panels support the flashing patterns described.
Structure and function
Function 3
A6V10401120_g_en_-- 19 | 46

Please also observe the documentation for your fire detection system.
3.3.3 Test mode
A test mode can be set on the control panel to test the radio manual call points.
When in test mode, alarms from the radio manual call points are not forwarded by
the control panel.
3.3.4 Alarm activation
lPress the pressure point on the glass or plastic insert.
aThe plastic insert falls down or
aThe glass insert breaks.
aThe alarm is activated
After an alarm is activated, the manual call point must be reset to a state in which it
is ready for operation.
3.3.5 Diagnosis levels
The radio manual call point monitors its operation largely autonomously.
The following diagnosis levels are derived from the different control measurements:
● Normal
● Replacement necessary
● Fault
When an error which impairs the radio manual call point's function occurs, a fault
message is signaled. To correct the cause of the fault, additional information is
available in the radio manual call point. This can be indicated with the FXS2061
SWING Tool. You will find more information in documentA6V10227643. See
chapter 'Applicable documents [➙7]'.
Structure and function
Function
3
20 | 46 A6V10401120_g_en_--