HP 9817 User manual

HP 9000 Series 200 Computers
Model
217
HP9817
CEHandbook
FA.,. HEWLETT
~~ PACKARD

HP 9817 CE Handbook
Note
This handbook is only for the use of HP-Qualified Service Personnel.
Hewlett-Packard Company
3404 East Harmony ROad. Fort Collins. Colorado 80525

Product Information
II
Environmental/Installation/PM I
Configuration I
Troubleshooting
II
Diagnostics I
Adjustments I
Peripherals I
Replaceable Parts
I
Diagrams
I
Reference
II
Service Notes
II

ii
Printing History
New editions of this manual will incorporate all material updated since the previous edition. Update
packages may be issued between editions and contain replacement and additional pages to be merged
into the manual
by the user. Each updated page will be indicated by a revision date at the bottom of
the page. A vertical bar
in the margin indicates the changes on each page. Note that pages which are
rearranged due to changes on a previous page are not considered revised.
The manual printing date and part number indicate its current edition. The printing date changes when
a new edition
is printed. (Minor corrections and updates which are incorporated at reprint do not
cause the date to change.) The manual part number changes when extensive technical changes are
incorporated.
December 1984... Edition 1. Replaces pari number 09817-90039.
May 1986...
Update
June 1986... Edition 2. Update incorporated.
NOTICE
The mtormanon contained In thiS document IS subjeCt to change without notICe
HEWLETI·PACKARD MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MANUAL, INCLUDING, BUT NOT LIMITED TO. THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett·Packard shall not be liable for errors contalfled her"," or direct. Indirect. specIal
incidental or consequential damages in connection with the furnishing, performance, or use of this matenal
WARRANTY
A copy of the specific warranty terms applicable to your Hewlett-Packard product and replacement parts can be obtained from your local Sales and Service Office

1-1
Chapter 1
Product Information
Information in this manual refers to the HP 9000 Series 200 Model 217 computer. The prod-
uct number of the Model 217 is HP9817. The terms "Model 217" and "HP9817" are used
interchangeably.
Type:
Clock frequency:
Internal architecture:
Address range:
Data bus:
Instruction types:
Major data types:
Addressing modes:
Interrupt levels:
Real-time clock
Resolution:
Accuracy:
Power-on reset:
Timers
Delay interrupt:
Cycled interrupt:
Match interrupt:
Range (nominal):
Duration:
Processor
J,lotorola 68010
8 MHz
32-bit data and address registers
16M bytes
16-bit asynchronous
57
5
14
6 maskable and 1 non-maskable
Clock and Timers
10 msec
50 ppm (4.3 sec/day)
Midnight, January 1
10 msecs to 1.94 days
10 msecs to 1.94 days
Match on time of day,
0.00 to 84600.00 seconds
(23.5 hours)
Beepers
81.375 Hz to 5208 Hz
0.01 to 2.55 sec
Beeper hardware supports three tone generators with attenuators and white noise source.

1-2 9817 Product Information
Features
• HP standard industrial package
• Six option card slots (three for external DIO interface cards)
• Pascal 3.0 and BASIC 3.0 language systems
• Supports external 14-inch medium-resolution, monochrome display
• HP-HIL keyboard support
Height:
Width:
Depth:
tlet weight:
Shipping weight:
Operating voltage:
Operating frequency:
Power consumption:
Backplane power*:
Physical
130 mm (5.12 inches)
325 mm (12.80 inches)
285 mm (11. 22 inches)
6 kg (13.2 pounds)
9.5 kg (20.9 pounds)
Power Requirements
90 to 125 Vac, 198 to 250 Vac
switch-selectable
48 to 66 Hz
130 vi (maximum)
41.251jJ @ +5 V
18.70 VI III +12 V
6 .
00 VI @ - 12 V
*The backplane +5 V lines are fuse-limited to 25 W for each pair of slots.

Product
Nwnber
HP 9817A
HP 9817H
9817 Product Information 1-3
Product Configuration
Description
Model 217 Computer
* Built-in HP-IB interface with 2 m cable
* Built-in RS-232 interface (order cable separately)
* 6-slot card cage for interfaces, language systems
and memory
Model 217 Computer
* Built-in HP-IB interface with 2 m cable
* Built-in RS-232 interface (order cable separately)
* 6-slot card cage for interfaces, language systems
and memory
512K bytes of RAM memory (two HP 98256A cards)
HP 46020A keyboard
HP 35721A, B or C 14-inch monochrome monitor
HP 98204B video interface
HP 35722A tilt and swivel unit
Option 001: 1M bytes RAM memory (one HP 9S257A
substituted for two HP 98256A cards)
Language Systems
Product Memory Requirements
Number Description RAM Disc
HP 98613A BASIC 3.0 512K bytes 512K bytes
HP 98615B Pascal 3.0 512K bytes 512K bytes

1-4 9817 Product Information
Backplane Accessories and Interface Cards
Product Description
No.
HP 98256A 256K byte RAM Card
HP98257A 1M byte RAM Card
HP98620B 2-channel DMA Controller (only one DMA controller can be used per mainframe)
HP98622A 16-bit GPIO Interface
(Opt. 001)
4.6 m (15 feet) unterminated cable
(Opt. 002) 0.8 m (2.5 feet) terminated cable for
HP 9885M Flexible Disc Drive
(Opt. 003)
4.6 m (15 feet) terminated cable for HP 6940AlB Multiprogrammer
(Opt. 004) 2.5 m (8.3 feet) terminated cable for
HP 9866A1B Thermal Printer
HP98623A
BCD Interface
(Opt. 001) 4.6 m (15 feet) unterminated cable
HP98624A HP-IB Interface
HP 10833A 1 m (3.3 feet) HP-IB cable
HP 10833B 2 m (6.6 feet) HP-IB cable
HP 10833C 4 m (13.2 feet) HP-IB cable
HP 10833D 0.5 m (1.6 feet) HP-IB cable
HP98625A Disc Interface (Pascal and SRM only)
HP98626A Serial Interface
(Opt. 001)
4.9 m (16 feet) RS-232 cable with DTE connector (male)
(Opt. 002)
4.9 m (16 feet) RS-232 cable with DCE connector (female)
HP 13265A 300 Baud Modem
HP 13266A Current Loop Interface
HP98627A
Color Video Interface (includes cables)
HP98628A
Datacomm Interface (BASIC and Pascal only. Always order with one personality option
and one or more cable options)
Personality Options
(Opt. 100) Async
and Data link ROM
Cable Options
(Opt. 001)
4.9 m (16 feet) RS-232-C DTE (male) cable with test connector
(Opt. 002)
4.9 m (16 feet) RS-232-C DCE (female) cable with test connector
(Opt. 003) 4.9 m (16 feet) RS-449/423
DTE (male) cable with test connector
(Opt. 099) No cable (for use with 1326X adapters)
HP 13264A Data
link Adaptor
HP 13265A
300 Baud Modem
HP 13266A Current Loop Interface
HP 98629A Resource Management Interface
(Opt. 001)
10m terminated cable
(Opt. 002)
25 m terminated cable
(Opt. 003)
60 m terminated cable
(Opt. 004)
60 m unterminated cable
HP 98691A Programmable Datacomm Interface with
4K RAM
(Opt. 001) 4.9 m (16 feet) RS-232-C
DTE (male) cable with test connector
(Opt. 002) 4.9 m (16 feet) RS-232-C DCE (female) cable with test connector
(Opt. 003)
4.9 m (16 feet) RS-449/423 DTE (male) cable with test connector
(Opt. 099) No cable
HP98630A
Breadboard Card
(Opt. 001) Backplane Extender Card
HP98255A
EPROM Card
HP98253A EPROM Development Kit (2 cards)
HP98259A 128K Byte Magnetic Bubble Memory Card
HP98635A
Floating-point Math Card

9817 Product Information 1-5
Accessory
Power
Requirements
Product Description
+5
+12
-12 Total
HP
9888A Bus
Expander 5.0
5.0
HP
13264A
Data Link Pod 0.2
1.9 0.3
2.4
HP
13265A
Modem
0.5
0.5
0.5 1.5
/H' i3266A
Current Loop Pod
1.0 1.0 1.0
3.0
HP 98028A
Res.
Mgmt.
iiUX
2.2
6.4
8.6
HP
98204B Video
VI/O Graph.
7.5
7.5
HP 98204B Video VI/Graphics
15.0
15.0
HP 98253A
EPROI·! Prog.
5.7
5.7
HP 98254A
64K byte RAM
3.0 3.0
HP
98255A
EPROM Card
2.8
2.8
HP
98256A
256K byte RAI.l
4.1
4.1
HP
98257A 1M byte RAt·l
6.0
6.0
HP 98259A
128K byte Bubble
2.4
2.9
5.3
HP
98601A
BASIC 2.0 ROM
2.4
2.4
HP
98601A
BASIC 1.0 ROM
2.3
2.3
HP
98602A
BASIC 2.1 ROM
3.6 3.6
HP
98604A
HPL 2.0 ROM
1.5
1.5
HP
98620A
DMA Controller
6.0 6.0
HP
98621A
BAS IC 1.0 Opt.
2.3
.3
HP 98622A
GPIO Interface
3.8
.8
HP
98623A
BCD Interface
2. 5 2.
HP
98624A HP-IB
Interface
2. 4 2.
HP
98625A
Disc Interface
3.0
0.1
3.1
HP
98626A RS-232
Interface
2.0
O. 6 0 6 3. 2
HP
98627A
Color Interface
5.5
5
.5
HP
98628A Datacomm
Interf.
3.6
O.
0 4.
HP 98629A
Resource Mgmt.
VI/O 98028A
3.7 O. 0.5
4.7
HP
98629A
Resource Mgmt.
w/98028A
5.9 6.9 0.5
13.3
HP
98630A
Breadboard Card
1.3 1.3
HP 98632A
MS-DOS Card
HP
98635A
Floating-Point
4.2 4.2
HP 98640A A-D Card
HP 98644A
Serial Load Card
HP 98691A
Progr.
Datacomm
6.4 2.0
1.3
9.7
HP 98695A
IBM 3270 Coax
09920-
66533 Keyboard/HP-IB
2.6
2.6
09920-
66534 Keyboard/HP-IB
2.6 2.6

1-6 9817 Product Information
Address Information
Decimal Approx.
16M-1
16M Bytes 9M
8M
6M
4M
256K
1K
o
Ram
Test/Monitor
External 1/0
Internal I/O
System ROM
Boots
Exception Table
Hex
FFFFFF
900000
800000
600000
400000
003FFF
000400
000000
9817 Memory Map
8M ,..------------,800000
External
1/0
6M ~-----------1600000
Internal
10
4M L..- _________ .....J 400000
Memory--Mapped 110
23 22 21 20 1918 17 16
Select Code
0-31
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
I/O Register Select
Standard Select Codes
Internal
External
0 Not Used HPIB
20 DataComm
CRT Alpha RS232
KYBD & ClK
10
Graphics
11
BCD
Flex-DIsc
12 GPIO
13
DMA
,.
DISC Intrfc
7 HPIB
External Address Format

2-1
Chapter 2
Environmental/Installation/PM
Environmental Range
Operating Temperature:
Humidity:
Storage Environment:
Maximum AILiLude:
EMI:
Line Transient Spike Immunity:
Additional regulatory compliance:
5% to 95% R.H. non-condensing, 40°C (104°F)
maximum wet-bulb temperature
-40°C to 75°C (-40°F to 167°F)
4600 metres (15 000 feet)
Conducted and radiated interference meets
VDE 073 and CISPR publication 11 standards.
Conducted and radiaLed interference also
meets FCC class A standards, although some
individual Model 217 computers may meet
FCC class B standards. Check the FCC label
on the rear panel.
1 kV (1 nsec. rise, 800 nsec. duration)
UL, CSA, IEC, SEV, FEI
These specifications apply to the Model 217, but not necessarily to any peripheral.
Installation
The 9817 is customer-installable.
Mounting
Tabouret or mini-rack, or unmounted (desktop).
Cabling
50-pin RS-232-C, HP-IB.
Site Preparation
Site preparation requirements are:
Environmental Class B or higher:
Otherwise
09817~90038. rev 5/86
No site prep needed
Upgrade site to Class B

2-2 9817 Environmental/Installation PM
Processor Board Switch Chart
Miscellaneous
Switches

Setting Processor Board Switches
RS-232 Handshake Type:
9817 Environmental/Installation PM 2-3
All values are non-operational and reserved for future use.
RS-232 Parity Type:
00 Parity bit
is
odd (default)
01 Parity bit is even
10
Parity bit 1 always
11 Parity bit
0
always
RS-232 Parity Enabled:
o Parity disabled (default)
Parity enabled
RS-232 Stop Bits:
o 1 stop bit per character (default)
1 1.5 stop bits for 5-bit characters, 2 bits otherwise
RS-232 Character Length:
00 5 bits per character
01 6 bits per character
10 7 bits per character
11 8 bits per character (default)
RS-232 Baud Rate:
0000 50
0001 75
0010 110
0011
134.5
0100 150
0101 200
0110 300
0111
600
1000 1200
1001 1800
1010 2400
(default)
1011 3600
1100 4800
1101 7200
1110 9600
1111 19200
Remote Keyboard Status:
o Local keyboard (default)
Remote keyboard
RS-232 Control Line Defeat:
o Control lines defeated
Control lines enabled (default)
This function enables or defeats the CD, CTR, DSR and OCRl control lines.
I

2-4 9817 Environmental/Installation PM
HP-IB System Controller:
o Computer is not system controller (HP-IB address 20)
Computer is system controller (HP-IB address 21) (default)
RAM Memory Test:
o Extended RAM test
Fast RAM test (default)
Self Test:
I 4, Self test runs continuously
C /1 Self test runs once at power-up (default)

9817 Environmental/Installation PM 2-5
. h RAM Starting Address
SettIng t e 1M Byte Cards
256K Byte Cards
First Card I
Second Card
Third Card
Fourth Card
Fifth Card
Sixth Card
Preventive Maintenance
No preventive maintenance is required.

2-6 9817 Environmental!Installation PM

3-1
Chapter 3
Configuration
The HP 9000 Model 217 is marketed in these configurations:
• HP 9817A: Computer only I

3-2 9817 Configuration
• HP9817H: Hardware system, includes the computer, HP46020A keyboard, HP98204B
video interface, HP 35721 14-inch monitor, HP 35722A tilt and swivel unit, and two
HP98256A (standard) or one HP98257A RAM cards (option 001)
~i
Refresh Select
50Hz 60Hz
@]
IT
~
14-pin connector
10 graphics card
ASCII/Roman 8 ASCII/Kalakana
Character Select
III
Standard
or
Option 001
HP 9817H Configuration
~

9817 Configuration 3-3
Processor Board Switch Chart
RS-232 Handshake Type:
All values are non-operational and reserved for future use.
RS-232 Parity Type:
00 Parity bit is odd (default)
01 Parity bit is even
10 Parity bit always
11 Parity bit 0 always
RS-232 Parity Enabled:
o Parity disabled (default)
Parity enabled
RS-232 Stop Bits:
o 1 stop bit per character (default)
1 1.5 stop bits for 5-bit characters, 2 bits otherwise
RS-232 Character Length:
00 5 bits
per
character
01 6 bits per
character
10 7 bits
per character
11 8 bits
per character
(default)
RS-232 Baud Rate:
0000 50
0001 75
0010 110
0011
134.5
0100 150
0101 200
0110 300
0111 600
1000 1200
1001 1800
1010 2400
(default)
1011 3600
1100 4800
1101 7200
1110 9600
1111 19200
Remote Keyboard Status:
o Local keyboard (default)
Remote keyboard
RS-232 Control Line Defeat:
o Control lines defeated
Control lines enabled (default)
This function enables or defeats CD, CTR, DSR and OCRl control functions.
I

3-4 9817 Configuration
HP-IB System Controller:
o Computer is not system controller (HP-IB address 20)
Computer is system controller (HP-IB address 21) (default)
RAM Memory Test:
o Extended RAM test
Fast RAM test (default)
Self Test:
o Self test runs continuously
Self test runs once at power-up (default)