HP StorageWorks 2000fc Guide

Page 1
481596-001
About this document
The chassis field replacement unit (FRU) replaces a chassis that has
been damaged or whose midplane has been damaged. To make a
fully functional chassis, you must install the following components
from the replaced chassis:
•Drive modules and air management modules
•Two power-and-cooling modules
•One or two controller modules (for a controller enclosure)
•One or two I/O modules (for a drive enclosure)
This document details procedures for removing drive modules/air
management modules, power-and cooling-modules, controller
modules, and I/O modules from the failed chassis and installing
them into the replacement chassis of an HP StorageWorks 2000
Family Modular Smart Array.
NOTE: Make sure you obtain the latest version of these
instructions from http://www.hp.com/go/msa. Select MSA SAN
Arrays, select your product, and go to Support.
Before you begin
•Turn the power-and-cooling supply modules off and disconnect
the power cables.
•Disconnect and label all cables.
CAUTION: Parts can be damaged by electrostatic discharge.
Use proper anti-static protection:
•Keep the replacement component in the ESD bag until needed.
•Wear an ESD wrist strap grounded to an unpainted surface of
the chassis.
•If an ESD wrist strap is unavailable, touch an unpainted surface
of the chassis before handling the component.
•Never touch connector pins.
Removing drive modules
NOTE: Air management modules are removed and installed
using the same procedure as removing and installing drive modules.
Printed on at least 50% total recycled fiber with at least 10%
post-consumer paper
© Copyright 2008 Hewlett-Packard Development Company, L.P.
First edition: March 2008
Product names mentioned herein may be trademarks of their
respective companies as reflected by an associated footnote. The
information in this document is subject to change without notice.
Printed in the US.
www.hp.com
HP StorageWorks
2000 Family Modular Smart
Array
chassis and midplane
replacement instructions

Page 2
1. Press and slide the release latch button to the right to disengage
the latch.
2. Pull the latch out toward the left to disengage the drive module
from the enclosure’s internal connector.
3. Wait 20 seconds for the internal disks to stop spinning, and pull
the drive module out of the enclosure.
Installing drive modules
1. Push the release latch button to the right to open the locking
mechanism.
2. Slide the drive module into the drive slot as far as it will go.
Removing power-and-cooling modules
1. Turn the thumbscrew (1) until it is disengaged from the
power-and-cooling module.
2. Rotate the latch (2) downward to disconnect the power module
from the internal connector, and slide it out from the slot (3).
Installing power-and-cooling modules
1. Slide the power-and-cooling module into the slot as far as it will
go.
2. Press the latch upward to engage the power-and-cooling module;
turn the thumbscrews finger-tight.
Removing controller modules
1. Turn the thumbscrews (2) until the screws disengage from the
controller.
1Release latch button
1
2
3
1Thumbscrew 2Latch
1Latch 2Thumbscrew
1
2
3
12 1 2

Page 3
2. Press both latches downward to disconnect the module from the
midplane.
3. Pull outward on the latches to slide the module out of the
enclosure.
Installing controller modules
1. Loosen the controller’s thumbscrews; press the latches downward.
2. Slide the controller into the enclosure as far as it will go (1).
3. Press the latches upward to engage the controller (2); turn the
thumbscrews finger-tight.
Removing I/O modules
1. Turn the thumbscrews (2) until the screws disengage from the I/O
module.
2. Press both latches downward to disconnect the I/O module from
the midplane.
3. Pull outward on the latches to slide the I/O module out of the
enclosure.
1
1
1
2
2
1Latch 2Thumbscrew
Service
12 1 2
Service
Service
Service

Page 4
Installing I/O modules
1. Loosen the controller’s thumbscrews; press the latches downward.
2. Slide the I/O module into the enclosure as far as it will go (1).
3. Press the latches upward to engage the I/O module (2); turn the
thumbscrews finger-tight.
Verifying component installation
•Reconnect cables and power on the system and associated data
host in the following order:
a. Drive enclosure first
b. Controller enclosure next
c. Data host last
•On the power-and-cooling modules, check that the AC Power
Good LED (top) is on.
•On the controller and I/O modules, check that the OK LED
(back) illuminates green, indicating that the module has
completed initializing and is online.
Additional information
See the MSA web site: http://www.hp.com/go/msa.
Service
Service
1
2
2