HP Z Turbo Drive Quad Pro User manual

HP Z Turbo Drive Quad Pro installation
Printed in
*838785-002*
838785-002

© 2015 HP Development Company, L.P.
Linux® is the registered trademark of Linus
Torvalds in the U.S. and other countries.
Windows is a trademark of the Microsoft group
of companies.
The information contained herein is subject to
change without notice. The only warranties for
HP products and services are set forth in the
express warranty statements accompanying
such products and services. Nothing herein
should be construed as constituting an
additional warranty. HP shall not be liable for
technical or editorial errors or omissions
contained herein.
Second Edition: October 2015
First Edition: August 2015
Document Part Number: 838785-002

HP Z Turbo Drive Quad Pro installation
Introduction
This document describes how to install the HP Z Turbo Drive Quad Pro into the HP Z440, Z640, and Z840
series workstations.
Kit contents
●HP Z Turbo Drive Quad Pro
●LED cable
●Installation instructions
●Warranty information
Before you begin
To view QuickSpecs and determine the compatibility of this product with your HP computer, see
http://www.hp.com/go/productbulletin.
The minimum BIOS revision for the HP Z440, Z640, and Z840 Workstations is 1.62. If these requirements are
not met, the computer does not recognize the drive.
If you are installing an operating system image on the drive, remove all other storage devices. Install this
drive in the primary PCIe slot indicated for your workstation and install the operating system image before
installing additional HP Z Turbo Drives or HP Z Turbo Drive Quad Pros or reinstalling the other storage devices.
The preferred slots are noted in the installation instructions for each computer. If you will be using the drive
as a data drive, you do not need to remove the other storage devices.
Introduction 1

Warnings and cautions
WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of a
hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce the risk of
injury from a hot component, enable the surface to cool before touching.
WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of an
electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed area
marked with this symbol.
WARNING! To reduce the risk of electric shock or damage to your equipment:
— Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
— Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.
— Disconnect power from the equipment by unplugging the power cord from the electrical outlet.
WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper
computer setup, posture, health, and work habits for computer users, and provides important electrical and
mechanical safety information. This guide is located at http://www.hp.com/ergo and on the documentation
CD (if one is included with the product).
WARNING! If a product is shipped in packaging marked with this symbol, , the product must always be
lifted by two persons to avoid personal injury due to product weight.
CAUTION: Static electricity can damage the electronic components of the computer. Before beginning these
procedures, be sure you discharge static electricity by briey touching a grounded metal object.
CAUTION: To prevent damage to the computer, observe the following Electrostatic Discharge (ESD)
precautions while performing the system parts removal and replacement procedures:
— Work on a static-free mat.
— Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body to
the ground.
— Create a common ground for the equipment you are working on by connecting the static-free mat, static
strap, and peripheral units to that piece of equipment.
NOTE: HP accessories are for use in HP computer products. They have been extensively tested for reliability
and are manufactured to high quality standards.
Installing additional M.2 modules in the HP Z Turbo Drive Quad
Pro
You can install up to four M.2 PCIe SSD modules in this drive. Load the modules from the cover hinge to the
PCIe edge connector in the following order.
TIP: Install all M.2 modules before installing the HP Z Turbo Drive Quad Pro assembly.
2 HP Z Turbo Drive Quad Pro installation

1. Open the drive cover.
a. Slide the latch to the left of the door to the left until the red area beneath the latch is fully exposed
(1).
b. Slide the right latch to the right and hold it (2).
c. While holding the right latch, press the center of the edge of the cover and lift it (3).
2. Loosen the two captive screws on the heat sink (1).
Installing additional M.2 modules in the HP Z Turbo Drive Quad Pro 3

3. Lift the heat sink to expose the M.2 modules (2).
NOTE: The drive comes with at least two M.2 modules preinstalled.
4. Remove the stando from the next M.2 slot.
4 HP Z Turbo Drive Quad Pro installation

5. Insert stando into the curve of the right edge of the M.2 module.
6. Slide the M.2 module into the connector (1) and then press down until the stando is aligned with the
embedded nut (2).
Installing additional M.2 modules in the HP Z Turbo Drive Quad Pro 5

7. Screw the stando into the nut.
8. Reinstall the heat sink (1) and tighten the captive screws (2).
Be sure that the tabs on the heat sink are under the metal pins and can rotate.
6 HP Z Turbo Drive Quad Pro installation

9. Close the cover (1) and slide the left latch to the right until no red is showing (2).
Installing additional M.2 modules in the HP Z Turbo Drive Quad Pro 7

Accessing the internal components of the computer
1. If you need help preparing the computer for this installation, consult the removal and replacement
procedures in the HP Customer Self Repair Services Media Library at http://www.hp.com/go/sml or in the
service guide for your computer at http://www.hp.com/support/manuals.
2. Power down the workstation, and then disconnect the power cord.
3. Power down all external devices, and then disconnect them from the workstation.
4. Remove the access panel by lifting up on the release latch and raising the panel from the chassis.
Installing the drive in an HP Z440 Workstation
If more than one of any of the following drives are to be installed in a system, a unique address for each drive
must be congured before installation:
●HP Z Turbo Drive
●HP Z Turbo Drive G2
●HP Z Turbo Quad Pro
For conguration instructions, see Installing multiple HP Z Turbo Drives or HP Z Turbo Quad Pro Drives
on page 14.
1. Press down on the two green PCI retention clips (1) located inside the workstation until they release,
and then rotate them down to raise the retention clamp (2).
8 HP Z Turbo Drive Quad Pro installation

2. Raise the slot cover (1) and rotate it toward the inside of the chassis (2) to access PCIe slot 5.
3. Align the connectors on the PCIe drive with the socket on the system board and install the drive into the
socket.
4. Connect the LED cable to the HDD activity header on the PCIe drive that is marked HDDACT_OUT. Then,
connect the other end of the LED cable to the HDD LED connector on the system board.
NOTE: To locate the HDD LED connector on the system board, see the System Board Overview on the
service panel.
Installing the drive in an HP Z440 Workstation 9

5. Press the two green PCI retention clamp tabs on the rear of the chassis up until they lock into place.
Installing the drive in an HP Z640 Workstation
If more than one of any of the following drives are to be installed in a system, a unique address for each drive
must be congured before installation:
●HP Z Turbo Drive
●HP Z Turbo Drive G2
●HP Z Turbo Quad Pro
For conguration instructions, see Installing multiple HP Z Turbo Drives or HP Z Turbo Quad Pro Drives
on page 14.
1. Press down on the two green PCI retention clips located on the rear of the chassis (1) until they release,
then rotate the clips down to raise the retention clamp from the slot covers (2).
10 HP Z Turbo Drive Quad Pro installation

2. Raise the slot cover (1) and rotate it (2) toward the inside of the chassis to access PCIe slot 5.
3. Align the connectors on the PCIe drive with the socket on the system board and install the drive into the
socket.
4. Connect the LED cable to the HDD activity header on the PCIe drive that is marked HDDACT_OUT. Then,
connect the other end of the LED cable to the HDD LED connector on the system board.
NOTE: To locate the HDD LED connector on the system board, see the System Board Overview on the
service panel.
Installing the drive in an HP Z640 Workstation 11

5. Press the two green PCI retention clamp tabs on the rear of the chassis up until they lock into place.
Installing the drive in an HP Z840 Workstation
If more than one of any of the following drives are to be installed in a system, a unique address for each drive
must be congured before installation:
●HP Z Turbo Drive
●HP Z Turbo Drive G2
●HP Z Turbo Quad Pro
For conguration instructions, see Installing multiple HP Z Turbo Drives or HP Z Turbo Quad Pro Drives
on page 14.
1. Squeeze the two green tabs together to release the retainer (1), rotate the PCI retainer (2) up, and lift it
out of the chassis (3).
12 HP Z Turbo Drive Quad Pro installation

2. Lift the green lever to rotate the retention bracket (1) out of the way, raise the slot cover (2), and then
rotate the slot cover toward the inside of the chassis (3) to access either PCIe slot 6, or slot 4.
3. Align the connectors on the PCIe drive with the socket on the system board and install the drive into the
socket, then lower the retention bracket into place.
NOTE: If the computer has one CPU installed, the drive may be used only in PCIe slot 6. If the computer
has a second CPU installed, the drive may also be used in slot 4.
4. Connect the LED cable to the HDD activity header on the PCIe drive that is marked HDDACT_OUT. Then,
connect the other end of the LED cable to the HDD LED connector on the system board.
NOTE: To locate the HDD LED connector on the system board, see the System Board Overview on the
service panel.
Installing the drive in an HP Z840 Workstation 13

5. Insert the hooks on the back end of the PCI retainer into the slots on the back of the chassis (1) and lock
the retainer in place by rotating it down into position (2).
NOTE: The PCI retainer locks the PCI retention clamp in place.
Installing multiple HP Z Turbo Drives or HP Z Turbo Quad Pro
Drives
Conguring the drive addresses
If more than one of any of the following drives are to be installed in a system, a unique address for each drive
must be congured before installation:
●HP Z Turbo Drive
●HP Z Turbo Drive G2
●HP Z Turbo Quad Pro
NOTE: A second HP Z Turbo Quad Pro can be installed on an HP Z840 with a second CPU only.
The HP Z Turbo Drive and HP Z Turbo Drive G2 both support a single M.2 module and have jumpers that can be
set to eight unique addresses. Each HP Z Turbo Drive and HP Z Turbo Drive G2 must have a unique address.
For possible jumper congurations and corresponding labels, see the following diagram.
14 HP Z Turbo Drive Quad Pro installation

The HP Z Turbo Drive Quad Pro has switches that can be set to four unique addresses. Each HP Z Turbo Drive
Quad Pro must have a unique address. For possible switch congurations and corresponding labels, see the
following diagram.
TIP: The black rectangle indicates the switch position.
Some of the HP Z Turbo Drive Quad Pro and HP Z Turbo Drive solutions addresses overlap. To prevent
conguration of identical addresses, see the following chart.
NOTE: HP recommends setting the addresses of any HP Z Turbo Drive Quad Pros, and then setting the
addresses of any HP Z Turbo Drive solutions. If using a combination of solutions, HP recommends using
Address C or Address D for the HP Z Turbo Drive Quad Pro and Address 0, Address 1, Address 2, or Address 3
for the HP Z Turbo Drive solution.
HP Z Turbo Drive and HP Z Turbo Drive G2
address
HP Z Turbo Drive Quad Pro address Instructions
0 A If an HP Z Turbo Drive Quad Pro is
congured at Address A, the HP Z Turbo
Drive solutions must not be at either
Address 0 or Address 1.
1
2 B If an HP Z Turbo Drive Quad Pro is
congured at Address B, the HP Z Turbo
Drive solutions must not be at either
Address 2 or Address 3.
3
4 C If an HP Z Turbo Drive Quad Pro is
congured at Address C, the HP Z Turbo
Drive solutions must not be at either
Address 4 or Address 5.
5
6 D If an HP Z Turbo Drive Quad Pro is
congured at Address D, the HP Z Turbo
Drive solutions must not be at either
Address 6 or Address 7.
7
Installing multiple HP Z Turbo Drives or HP Z Turbo Quad Pro Drives 15

Conguring the LED cables
If more than one of any of the following drives are to be installed in a system, you must congure the LED
cables between the drives and the system board as follows.
To congure the LED cables on a system with two HP Z Turbo Drive Quad Pros:
1. Connect an LED cable to the HDD activity header on the rst PCI drive that is marked HDDACT_OUT.
2. Connect the other end of this LED cable to the HDD activity header on the second PCI drive that is
marked HDDACT_IN.
3. Connect an LED cable to the HDD activity header on the second PCI drive that is marked HDDACT_OUT.
4. Then, connect the other end of this LED cable to the HDD LED connector on the system board.
NOTE: To locate the HDD LED connector on the system board, see the System Board Overview on the
service panel.
To congure the LED cables on a system with an HP Z Turbo Drive Quad Pro and an HP Z Turbo Drive:
1. Connect an LED cable to the HDD activity header on the HP Z Turbo Drive that is marked HDDACT1.
2. Connect the other end of this LED cable to the HDD activity header on the HP Z Turbo Drive Quad Pro that
is marked HDDACT_IN.
3. Connect an LED cable to the HDD activity header on the HP Z Turbo Drive Quad Pro that is marked
HDDACT_OUT.
4. Then, connect the other end of this LED cable to the HDD LED connector on the system board.
NOTE: To locate the HDD LED connector on the system board, see the System Board Overview on the
service panel.
Completing the installation
1. Reinstall the access panel.
2. Reconnect the AC power cord and turn on the workstation.
Conguring the computer
The HP Z Turbo Drive Quad Pro is an NVMe device. NVMe devices require a driver for proper detection and
operation. Windows® 8 and higher have this driver by default. To download the driver for Windows 7, go to
http://www.hp.com/go/workstationsupport.
For Linux®, an NVMe driver was merged into version 3.3 of the Linux kernel.
When powering up the computer after installation, a new hard drive identies itself as uninitialized storage.
See the operating system documentation for information about how to set up the new drive.
CAUTION: If you are installing an operating system image on the drive, remove all other storage devices.
Verify that you installed this drive in the primary PCIe slot indicated for your workstation, and then install the
operating system image before installing a second drive of the same type or reinstalling the other storage
devices. The preferred slots are noted in the installation instructions for each computer. If you are using the
drive as a data drive, you do not need to remove the other storage devices.
NOTE: Some operating systems automatically schedule defragmenting sessions. This oers no benet for
an SSD; therefore, the user can remove the automatic scheduling. This will also save energy.
16 HP Z Turbo Drive Quad Pro installation