HPE Aruba Networking 630 Series User manual

HPE Aruba Networking 630
Series Campus Access Point
Installation Guide

HPE Aruba Networking 630 Series Campus Access Point | Installation Guide Edition 1 | September 2023
Copyright Information
© Copyright 2023 Hewlett Packard Enterprise Development LP.
Open Source Code
This product includes code licensed under certain open source licenses which require source compliance.
The corresponding source for these components is available upon request. This offer is valid to anyone in
receipt of this information and shall expire three years following the date of the final distribution of this
product version by Hewlett Packard Enterprise Company. To obtain such source code, please check if the
code is available in the HPE Software Center at https://myenterpriselicense.hpe.com/cwp-ui/software but, if
not, send a written request for specific software version and product for which you want the open source
code. Along with the request, please send a check or money order in the amount of US $10.00 to:
Hewlett Packard Enterprise Company
Attn: General Counsel
WW Corporate Headquarters
1701 E Mossy Oaks Rd, Spring, TX 77389
United States of America.

Contents
Contents 1
About This Guide 3
Guide Overview 3
Related Documentation 3
Contacting Support 3
Hardware Overview 4
Package Contents 4
Front View 4
External Antenna Connectors 5
LEDs 5
Back View 7
Bluetooth 5.0 Low Energy and 802.15.4 Radio 8
Micro-B Console Port 8
Ethernet Ports 8
Kensington Lock Slot 8
USB 2.0 Interface 8
Reset Button 8
Power 9
BLE Radio Default State 9
Console Port Default State 9
USB Host Interface Default State 9
Installation 10
Before You Begin 10
Identifying Specific Installation Locations 11
Software 12
Verifying Post-Installation Connectivity 12
Specifications, Safety, and Compliance 13
HPE Aruba Networking 630 Series Campus Access Point Specifications 13
Regulatory Model Name 13
Regulatory considerations for AP-634 13
Brazil 14
Canada 14
EAC 15
European Union and United Kingdom 15
India 16
Japan 16
Korea 16
Medical 17
HPE Aruba Networking 630 Series Campus Access Point |Installation Guide 1
Contents

HPE Aruba Networking 630 Series Campus Access Point |2
Mexico 17
Morocco 17
Peru 18
Philippines 18
Singapore 18
Taiwan 18
Thailand 19
Ukraine 19
United States 19
Proper Disposal of HPE Aruba Networking Equipment 21

About This Guide
This document describes the hardware features of the HPE Aruba Networking 630 Series Campus Access Point. It
provides a detailed overview of the physical and performance characteristics of each access point model and
explains how to install the access point.
Guide Overview
nHardware Overview provides a detailed hardware overview of the HPE Aruba Networking 630 Series Campus
Access Point.
nInstallation describes how to install the HPE Aruba Networking 630 Series Campus Access Point .
nSpecifications, Safety, and Compliance lists the HPE Aruba Networking 630 Series Campus Access Point's
technical specifications and safety and regulatory compliance information.
Related Documentation
You require the following documents for the complete management of HPE Aruba Networking access point.
nLatest document of the software user guide:
https://www.arubanetworks.com/techdocs/ArubaDocPortal/content/cons-aos-home.htm
nCLI bank: https://www.arubanetworks.com/techdocs/CLI-Bank/Content/Home.htm
Contacting Support
Main Site arubanetworks.com
Support Site asp.arubanetworks.com
Airheads Social Forums and Knowledge
Base
community.arubanetworks.com
North American Telephone [phone] (Toll Free)
1-408-754-1200
International Telephone arubanetworks.com/support-services/contact-support/
Software Licensing Site lms.arubanetworks.com
End-of-life Information arubanetworks.com/support-services/end-of-life/
Security Incident Response Team Site: arubanetworks.com/support-services/security-bulletins/
Email: [email protected]
Table 1: Contact Information
HPE Aruba Networking 630 Series Campus Access Point |Installation Guide 3
Chapter 1
About This Guide

Hardware Overview
The HPE Aruba Networking 630 Series Campus Access Point supports the IEEE 802.11ax WLAN standard in the 6
GHz band (Wi-Fi 6E) as well as the 5 GHz and 2.4 GHz bands, delivering high performance and capacity with MIMO
(Multiple-Input, Multiple-Output) and OFDMA (Orthogonal Frequency Division Multiple Access) technologies, while
also supporting IEEE 802.11a/b/g/n/ac wireless services.
Package Contents
Inform your supplier to check if there are any incorrect, missing, or damaged parts. If possible, retain the carton,
including the original packing materials. Use these materials to repack and return the unit to the supplier if needed.
Table 2: Package Contents
Item Quantity
HPE Aruba Networking 630 Series Campus
Access Point
1
The AP mount bracket attaches to a variety of mount kits (sold separately). Refer to the HPE Aruba
Networking 630 Series Campus Access Point ordering guide for details.
Front View
Figure 1 AP-635 Front View
HPE Aruba Networking 630 Series Campus Access Point |Installation Guide 4
Chapter 2
Hardware Overview

HPE Aruba Networking 630 Series Campus Access Point |5
Figure 2 AP-634 Front View
External Antenna Connectors
The AP-634 access point has two sets of two RP-SMA female connectors for external antennas:
nFirst set (labeled as A0 and A1): 2.4GHz and 5GHz, combined (diplexed)
nSecond set (labeled as B0 and B1): 6GHz
External antennas for this device must be installed by a professional installer, using manufacturer-
approved antennas only. The Equivalent Isotropically Radiated Power (EIRP) levels for all external
antenna devices must not exceed the regulatory limit set by the host country/domain. Installers are
required to record the antenna gain for this device in the system management software. A list of
approved antennas can be found in the ordering guide at
https://www.arubanetworks.com/resource/aruba-630-series-campus-access-points-ordering-guide
Les antennes externes pour cet appareil doivent être installées par un professionnel agréé, en utilisant
uniquement des antennes approuvées par le fabricant. Les niveaux équivalents de puissance à
rayonnement isotrope (EIRP) pour tous les périphériques d'antenne externe ne doivent pas dépasser la
limite réglementaire définie par le pays hôte / domaine. Les installateurs doivent enregistrer le gain
d'antenne pour cet appareil dans le logiciel de gestion du système. Une liste d'antennes approuvées
peut être trouvée à https://www.arubanetworks.com/resource/aruba-630-series-campus-access-points-
ordering-guide
For the 6 GHz band, the AP-634 is approved in the US (5925-6425 MHz and 6525-6875 MHz) and Canada (5925-6875
MHz) for Standard Power operations (in conjunction with an Automated Frequency Coordination [AFC] system).
LEDs
The LED indicators located on the front cover of the access point indicate the following functions:
System Status LED
The System Status LED indicates the operating condition of the access point.

Color/State Meaning
Off Device Powered off
Green- solid Device ready, fully functional, no network
restrictions
Green- blinking 1Device booting, not ready
Green- flashing off 2Device ready, fully functional, uplink negotiated
in sub-optimal speed (< 1 Gbps)
Green- flashing on3Device in deep-sleep mode
Amber- solid Device ready, restricted power mode (limited
PoE power available, or IPM restrictions
applied), no network restrictions
Amber- flashing off Device ready, restricted power mode (limited
PoE power available, or IPM restrictions
applied), uplink negotiated in sub-optimal
speed (< 1 Gbps)
Red System error condition - Immediate attention
required
Table 3: System Status LED
1. Blinking: one second on, one second off, 2 seconds cycle.
2. Flashing off: mostly on, fraction of a second off, 2 seconds cycle.
3. Flashing on: mostly off, fraction of a second on, 2 seconds cycle.
2GHz/5GHz/6GHz Radio Status LEDs
The 2GHz/5GHz/6GHz Radio Status LEDs indicate the operating mode of the access point’s 2GHz/5GHz/6GHz
radios.
Color/State Meaning
Off Device Powered off, or radio disabled
Green- solid Radio enabled in access mode
Green- flashing off 1Radio enabled in uplink or mesh mode
Amber- solid Radio enabled in monitor or spectrum analysis
mode
Table 4: 2GHz/5GHz/6GH Radio Status LEDs
1. Flashing off: mostly on, fraction of a second off, 2 seconds cycle.
LED Display Settings
The LEDs have three operating modes that can be selected in the system management software:
HPE Aruba Networking 630 Series Campus Access Point |Installation Guide 6

HPE Aruba Networking 630 Series Campus Access Point |7
nDefault mode:refer to Table 3 and Table 4
nOff mode: all LEDs are off
nBlink mode: all LEDs blink green (synchronized)
To force the LEDs into off mode or back to software defined mode, press the reset button for a short duration (less
than 10 seconds).
Pressing the reset button for longer than 10 seconds may cause the AP to reset and return to factory
default state.
Back View
The ports on the back of the AP-634 access point are the same as the ones on the back of the AP-635 access point.
Figure 3 Back View (AP-635)
Table 5: Ports on Back of HPE Aruba Networking 630 Series Campus Access Point
Callout Component
1 USB 2.0 Interface
2 Micro-B Console Port
3 Reset Button
4 Kensington Lock Slot
5 DC Jack

Callout Component
6 E1Ethernet Port
7 E0 Ethernet Port
Bluetooth 5.0 Low Energy and 802.15.4 Radio
The access point is equipped with an integrated BLE 5.0 and 802.15.4 radio that provides the following capabilities:
nLocation beacon applications
nWireless console access
nIOT gateway applications
Micro-B Console Port
The console port is a Micro-B connector located on the back of the access point. Use the proprietary AP-CBL-SERU
cable or AP-MOD-SERU module (sold separately) for direct management of the access point when connected to a
serial terminal or laptop.
Figure 4 Micro-B Console Port Pin-out
1: NC
2: RXD
3: TXD
4: GND
5: GND
Ethernet Ports
The HPE Aruba Networking 630 Series Campus Access Point is equipped with two 100/1000/2500Base-T auto-
sensing MDI/MDX wired RJ45 Ethernet ports (E0 and E1). The 2.5bps speed complies with NBase-T and 802.3bz
specifications. Both ports are compliant with 802.3ab 1000Base-T Gigabit Ethernet and 802.3az (Energy Efficient
Ethernet) standards. Both ports support 802.3at and 802.3bt Power over Ethernet compliance to accept power
from a POE source, such as a PoE midspan injector, or a network switch.
The cable guiding features on the chassis are useful only in specific use cases, such as using the
extension cables or other cables with short plugs. To use the cable guiding feature, the Ethernet cable
bend radius shall be no more than 20 mm.
Kensington Lock Slot
The HPE Aruba Networking 630 Series Campus Access Point is equipped with a Kensington lock slot for additional
physical security.
USB 2.0 Interface
The USB 2.0 interface located on the top of the HPE Aruba Networking 630 Series Campus Access Point is
compatible with selected cellular modems and other peripherals. When active, this interface can supply up to
5W/1A to a connected device.
Reset Button
HPE Aruba Networking 630 Series Campus Access Point |Installation Guide 8

HPE Aruba Networking 630 Series Campus Access Point |9
The reset button located on the bottom of the device can be used to reset the access point to factory default
settings or turn off/on the LED display.
Use one of the following methods to reset the access point to factory default settings:
nTo reset during normal operation, hold the reset button for more than 10 seconds while the access point is
running, and then release the reset button.
nTo reset during power up, hold the reset button while the access point is powering up.
The system status LED will flash again within 15 seconds indicating that the reset is completed. The access point will
now continue to boot with the factory default settings.
To toggle the LED displayinto off mode or back to software defined mode, press the reset button for a short
duration (less than 10 seconds).
Power
Both E0 and E1 ports support PoE-in (AP is a PoE-PD device), allowing the device to draw power from compliant PoE
power sources. If PoE is not available, a proprietary AP-AC2-12B power adapter (sold separately) can be used to
power the access point. When both PoE and DC power sources are available, the DC power source takes
precedence. In that case, the access point simultaneously draws a minimal current from the PoE source. In the
event that the DC source fails, the access point switches to the PoE sources.
The Intelligent Power Monitoring (IPM) feature may also be used to manage the power consumption preferences
for this device. When enabled, the user may enable/disable power restrictions for the access point using HPE Aruba
Networking's AP management software. Refer to the HPE Aruba Networking 630 Series Campus Access Point
datasheet for details on possible functional restrictions when the AP is powered by POE, and how IPM can help to
avoid or minimize these restrictions.
BLE Radio Default State
When the access point is in factory default state the integrated BLE radio is enabled. This applies to the non-TAA
product SKUs only. On the TAA products, the BLE radio is disabled when the unit is in factory default conditions.
Once the AP has established a connection with its management platform, the BLE radio state is updated to match
what’s configured there. This state is maintained if the AP is power-cycled or rebooted.
Console Port Default State
When the access point is in factory default state the console interface (both physical port and BLE) is enabled with
default credentials (username is “admin” and password is the serial number of the unit). Once the AP has
established a connection with its management platform, the console port state (enabled/disabled) and access
credentials are updated to match what’s configured there. State and credentials are maintained if the AP is power-
cycled or rebooted.
USB Host Interface Default State
When the access point is in factory default state the USB host interface is powered and enabled, assuming the AP is
not in a restricted power mode. On some AP models the USB port may be disabled when a POE source with
insufficient power budget is used. Once the AP has established a connection with its management platform, the
USB host interface state is updated to match what’s configured there. This state is maintained if the AP is power-
cycled or rebooted.

Installation
The HPE Aruba Networking 630 Series Campus Access Point is designed for ceiling or wall mounted deployments.
Several optional mount kits are available to attach the access point to a variety of surfaces. These mount kits are
available as accessories and must be ordered separately. Refer to the HPE Aruba Networking 630 Series Campus
Access Point ordering guide at https://www.arubanetworks.com.
All HPE Aruba Networking access points should be professionally installed by a professional installer.
The installer is responsible for ensuring that grounding is available and meets applicable national and
electrical codes. Failure to properly install this product may result in physical injury and/or damage to
property.
Tous les points d'accès HPE Aruba Networking doivent impérativement être installés par un
professionnel agréé. Ce dernier doit s'assurer que l'appareil est mis à la terre et que le circuit de mise à
la terre est conforme aux codes électriques nationaux en vigueur. Le fait de ne pas installer
correctement ce produit peut entraîner des blessures corporelles et / ou des dommages matériels.
The installer is responsible for securing the access point onto the ceiling tile rail. Failure to properly
install this product may result in physical injury and/or damage to property.
Use of accessories, transducers and cables other than those specified or provided by the manufacturer
of this equipment could result in increased electromagnetic emissions or decreased electromagnetic
immunity of this equipment and result in improper operation.
For indoor use only. The access point, AC adapter, and all connected cables are not to be installed
outdoors. This stationary device is intended for stationary use in partly temperature controlled weather-
protected environments (class 3.2 per ETSI 300 019).
Before You Begin
Refer to the sections below before beginning the installation process.
FCC Statement: Improper termination of access points installed in the United States configured to non-
US model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or
intentional violation may result in a requirement by the FCC for immediate termination of operation and
may be subject to forfeiture (47 CFR 1.80).
HPE Aruba Networking 630 Series Campus Access Point |Installation Guide 10
Chapter 3
Installation

HPE Aruba Networking 630 Series Campus Access Point |11
Pre-Installation Checklist
Before installing the access point, be sure that you have the following (not included with the AP):
nA mount kit compatible with the AP and mount surface
nOne or two Cat5E or better UTP cables with network access
nCompatible antenna(s) when installing AP-634
Some optional items:
nA compatible power adapter with power cord
nA compatible PoE midspan injector with power cord
nAn AP-CBL-SERU console cable
nAn AP-MOD-SERU console module
Refer to the HPE Aruba Networking 630 Series Campus Access Point ordering guide for compatible items, quantities
needed, etc.
Also, make sure at least one of the following network services is supported:
nHPE Aruba Networking Discovery Protocol (ADP)
nDNS server with an “A” record
nDHCP Server with vendor specific options
If a power adapter other than the HPE Aruba Networking-approved adapter is used in the US or
Canada, it should be NRTL listed, with an output rated 12V DC, minimum 0.75A, marked “LPS” and
“Class 2,” and suitable for plugging into a standard power receptacle in the US and Canada.
Identifying Specific Installation Locations
The HPE Aruba Networking 630 Series Campus Access Point is designed in compliance with
governmental requirements, so that only authorized network administrators can change
configuration settings. For more information about AP configuration, refer to the AP Software Quick
Start Guide.
Use of this equipment adjacent to or stacked with other equipment should be avoided because it could
result in improper operation. If such use is necessary, this equipment and the other equipment should
be observed to verify that they are operating normally.
Use the access point placement map generated by HPE Aruba Networking RF Plan software application to
determine the proper installation location(s). Each location should be as close as possible to the center of the
intended coverage area and should be free from obstructions or obvious sources of interference. These RF
absorbers/reflectors/interference sources will impact RF propagation and should be accounted for during the
planning phase and adjusted for in RF plan.
Identifying Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase
is critical. Make sure that these sources are taken into consideration when you attach an access point to its fixed
location.
RF absorbers include:
nCement/concrete—Old concrete has high levels of water dissipation, which dries out the concrete, allowing for
potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking RF
signals.
nNatural Items—Fish tanks, water fountains, ponds, and trees
nBrick
RF reflectors include:
nMetal Objects—Metal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows,
blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets.
nDo not place an access point between two air conditioning/heating ducts. Make sure that access points are
placed below ducts to avoid RF disturbances.
RF interference sources include:
nMicrowave ovens and other 2.4 or 5 GHz objects (such as cordless phones)
nCordless headset such as those used in call centers or lunch rooms
Portable RF communications equipment (including peripherals such as antenna cables and external
antennas) should be used no closer than 30 cm (12 inches) to any part of the access point. Otherwise,
degradation of the performance of this equipment could result.
Software
For instructions on choosing operating modes and initial software configuration, refer to the AP Software Quick
Start Guide .
HPE Aruba Networking access points are classified as radio transmission devices, and are subject to
government regulations of the host country. The network administrator(s) is/are responsible for
ensuring that configuration and operation of this equipment is in compliance with their country’s
regulations. For a complete list of approved channels in your country, refer to the HPE Aruba
Networking Downloadable Regulatory Table.
Verifying Post-Installation Connectivity
The integrated LED on the access point can be used to verify that the access point access point is receiving power
and initializing successfully (see Table 1-Table 2). Refer to the AP Software Quick Start Guide for further details on
verifying post-installation network connectivity.
HPE Aruba Networking 630 Series Campus Access Point |Installation Guide 12

Specifications, Safety, and Compliance
This chapter provides an overview of the HPE Aruba Networking 630 Series Campus Access Point specifications,
safety, and compliance information.
HPE Aruba Networking 630 Series Campus Access Point
Specifications
Electrical
nEthernet
oE0 port: 100/1000/2500Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port
oE1 port: 100/1000/2500Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port
nPower
o12V DC power interface, support powering through AC-to-DC power adapter (AP-AC2-12B)
oPower over Ethernet (PoE): 802.3at or 802.3bt compliant source
Environmental
nOperating
oTemperature Range: 0 °C to 50 °C (32 °F to 122 °F)
oHumidity Range: 5% to 95% non-condensing
nStorage and Transportation
oTemperature Range: –25 °C to 55 °C (–13 °F to 131 °F)
oHumidity Range: 10% to 100% non-condensing
For additional specifications on this product, please refer to the HPE Aruba Networking 630 Series Campus Access
Point data sheet. The data sheet can be found at https://www.arubanetworks.com.
Regulatory Model Name
For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique
regulatory model number (RMN). The regulatory model number can be found on the product nameplate label,
along with all required approval markings and information. When requesting compliance information for this
product, always refer to this regulatory model number. The regulatory model number RMN is not the marketing
name or model number of the product.
The regulatory model name for the HPE Aruba Networking 630 Series Campus Access Point:
nAP-634 RMN: APIN0634
nAP-635 RMN: APIN0635
Regulatory considerations for AP-634
The AP-634 will be offered in countries where there is an existing or clear and defined path to allow operation of 6
GHz radios with external connectorized antennas, either as a Low Power Indoor (LPI) or Standard Power (SPI)
HPE Aruba Networking 630 Series Campus Access Point |Installation Guide 13
Chapter 4
Specifications, Safety, and Compliance

HPE Aruba Networking 630 Series Campus Access Point |14
product. Please contact your HPE Aruba Networking representative to confirm (existing or planned) availability for
the country where the AP will be deployed.
Brazil
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em
sistemas devidamente autorizados.
O uso deste equipamento é restrito a ambientes fechados e proibido em plataformas petrolíferas, carros, trens,
embarcações e no interior de aeronaves abaixo de 3.048 m (10.000 pés).
Para mais informações, consulte o site da Anatel: https://www.gov.br/anatel/pt-br
Canada
Innovation, Science and Economic Development Canada
This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment
Regulations.
In accordance with Innovation, Science and Economic Development Canada regulations, this radio transmitter and
receiver may only be used with an antenna, the maximum type and gain of which must be approved by Innovation,
Science and Economic Development Canada. To reduce potential radio interference, the type of antenna and its
gain shall be chosen so that the equivalent isotropic radiated power (EIRP) does not exceed the values necessary
for effective communication.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation of this device is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference, including interference that
may cause undesired operation.
When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the
potential for harmful interference with co-channel Mobile Satellite Systems.
The device could automatically discontinue transmission in case of absence of information to transmit, or
operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the
use of repetitive codes where required by the technology.
This radio transmitter model APIN0634 has been approved by Innovation, Science and Economic Development
Canada to operate with the antenna types listed in the HPE Aruba Networking 630 Series Campus Access Point
ordering guide (link provided below) below, with the maximum permissible gain indicated. Antenna types not
included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly
prohibited for use with this device.
https://www.arubanetworks.com/resource/aruba-630-series-campus-access-points-ordering-guide
Operation shall be limited to indoor use only.
Operation on oil platforms, cars, trains, boats, and aircraft shall be prohibited except for on large
aircraft flying above 10,000 feet.
Innovation, Sciences et Développement économique Canada

Cet appareil numérique de Classe B répond à toutes les exigences de la réglementation canadienne sur le matériel
brouilleur.
Conformément à la réglementation d’Innovation, Sciences et Développement économique Canada, le présent
émetteur-récepteur radio ne peut être utilisé qu’avec une antenne d’un type et d’un gain maximal approuvé par
Innovation, Sciences et Développement économique Canada. Dans le but de réduire les risques d’interférence
radioélectrique, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée
équivalente (P.I.R.E.) ne dépasse pas les valeurs nécessaires à l’établissement d’une communication efficace.
Cet appareil contient des émetteurs / récepteurs exemptés de licence qui sont conformes aux RSS exempts de
licence d'Innovation, Sciences et Développement économique Canada. Son fonctionnement est soumis aux deux
conditions suivantes: (1) ce périphérique ne doit pas provoquer d’interférences, et (2) ce périphérique doit accepter
toute interférence, y compris les interférences susceptibles de provoquer un dysfonctionnement.
Pour un fonctionnement dans la bande de fréquences comprises entre 5,15 et 5,25 GHz, son utilisation est limitée à
un environnement intérieur afin de réduire la possibilité d’interférences nuisibles avec les systèmes mobiles par
satellite opérant sur le même canal.
Ce modèle d'émetteur radio APIN0534 a été approuvé par Industrie Canada pour fonctionner avec les types
d'antenne énumérés dans le guide de commande en ligne (lien ci-dessous) avec le gain maximal admissible
indiqué. Les types d'antennes non inclus dans cette liste, ayant un gain supérieur au gain maximal indiqué pour ce
type, sont strictement interdits pour une utilisation avec cet appareil.
https://www.arubanetworks.com/resource/aruba-630-series-campus-access-points-ordering-guide
Le fonctionnement est restreint à une utilisation à l’intérieur seulement.
L’utilisation sur les plateformes pétrolières ou dans les voitures, les trains, les bateaux et les avions est
interdite, à l’exception des gros avions volant à plus de 3 km (10 000 pi).
EAC
TOO «Хьюлетт-Паккард (К)», Республика Казахстан, 050040, г. Алматы, Бостандыкский район, проспект Аль-
Фараби, 77/7, Телефон/факс: + 7 727 355 35 50
ЖШС «Хьюлетт-Паккард (К)», Қазақстан Республикасы, 050040, Алматы к., Бостандык ауданы, Әл-Фараби
даңғылы, 77/7, Телефон/факс: [phone]
European Union and United Kingdom
The Declaration of Conformity made under Radio Equipment Directive 2014/53/EU as well as the United Kingdom's
Radio Equipment Regulations 2017/UK is available for viewing below. Select the document that corresponds to your
device’s model number as it is indicated on the product label.
EU&UK Declaration of Conformity
Compliance is only assured if the HPE Aruba Networking approved accessories as listed in the HPE Aruba
Networking 630 Series Campus Access Point ordering guide are used.
This device is limited for indoor use. Use in trains with metal-coated windows (or similar structures made of
materials with comparable attenuation characteristic) and aircraft is permitted. Operations in the 6GHz band are
blocked by firmware for some countries pending adoption of spectrum. Refer to HPE Aruba Networking DRT
release notes for details.
Wireless Channel Restrictions
HPE Aruba Networking 630 Series Campus Access Point |Installation Guide 15

HPE Aruba Networking 630 Series Campus Access Point |16
5150-5350MHz band is limited to indoor only in the following countries; Austria (AT), Belgium (BE), Bulgaria (BG),
Croatia (HR), Cyprus (CY), Czech Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR), Germany (DE),
Greece (GR), Hungary (HU), Iceland (IS), Ireland (IE), Italy (IT), Latvia (LV), Liechtenstein (LI), Lithuania (LT),
Luxembourg (LU), Malta (MT), Netherlands (NL), Norway (NO), Poland (PL), Portugal (PT), Romania (RO), Slovakia
(SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH), Turkey (TR), United Kingdom (UK (NI)).
Radio Frequency Range MHz Max EIRP
BLE/Zigbee 2402-2480 10 dBm
Wi-Fi 2412-2472 20 dBm
5150-5250 23 dBm
5250-5350 23 dBm
5470-5725 30 dBm
5725-5850 14 dBm
Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS
User Guide/Instant User Guide for details on restrictions.
UKCA Marking
India
This product conforms to the relevant Essential Requirements of TEC, Department of Telecommunications, Ministry
of Communications, Govt of India, New Delhi-110001
Japan
Korea

Medical
1. Equipment not suitable for use in the presence of flammable mixtures.
2. Connect to only IEC 60950-1 or IEC 60601-1 certified products and power sources. The end user
is responsible for the resulting medical system complies with the requirements of IEC 60601-1.
3. Wipe with a dry cloth, no additional maintenance required.
4. No serviceable parts, the unit must be sent back to the manufacturer for repair.
5. No modifications are allowed without approval from HPE Aruba Networking.
Use of this equipment adjacent to or stacked with other equipment should be avoided because it could
result in improper operation. If such use is necessary, this equipment and the other equipment should
be observed to verify that they are operating normally.
Use of accessories, transducers and cables other than those specified or provided by the manufacturer
of this equipment could result in increased electromagnetic emissions or decreased electromagnetic
immunity of this equipment and result in improper operation.
Portable RF communications equipment (including peripherals such as antenna cables and external
antennas) should be used no closer than 30 cm (12 inches) to any part of the access point. Otherwise,
degradation of the performance of this equipment could result.
This device is intended for indoor use in professional healthcare facilities.
This device has no IEC/EN60601-1-2 essential performance.
Compliance is based on the use of HPE Aruba Networking approved accessories. Refer to the ordering
guide for this access point at https://www.arubanetworks.com
Mexico
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o
dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debeaceptar cualquier interferencia,
incluyendo la que pueda causar su operación no deseada.
Morocco
HPE Aruba Networking 630 Series Campus Access Point |Installation Guide 17

HPE Aruba Networking 630 Series Campus Access Point |18
Peru
En el Perú, este equipo diseñado para la banda de 5 925 – 7 125 MHz, debe ser configurado para operar
únicamente en interiorescon una PIRE de hasta 1 W (30 dBm) y sujeto a las Condiciones de Operación que
establezca el MTC.
Philippines
Singapore
Taiwan
第十二條
取得審驗證明之低功率射頻器材，非經許可，公司，商號或使用者均不得擅自變更頻率、加大功率或變更原設
計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干
擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電
波輻射性電機設備之干擾。
1.應避免影響附近雷達系統之操作。
2.高增益指向性天線只得應用於固定式點對點系統
3.電磁波暴露量 MPE 標準值 1 mW/cm2, 送測產品實測值為 : 0.2044mW/cm2