HUANUO HNCPB User manual

Model: HNCPB
V5.0
CPU Holder Instruction Manual
Thank you for choosing this HUANUO product! At HUANUO we
strive to provide you with the best quality products and
services in the industry. Please share your experience of our
product with others at www.huanuoav.com/reviews if you are
satisfied. Should you have any issues, please don't hesitate to
contact us.
Technical Support:
1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA)
Website:
www.huanuoav.com

Supp
Supplied Parts and Hardware List
Tools Needed (Not lncluded)
1
IMPORTANT SAFETY INFORMATION
• Please read through these instructions completely before attempting
installation. If you do not understand the instructions or have any concerns or
questions, please contact customer service at [email protected].
• Check package contents against Supplied Parts and Hardware List to assure
that all components were received undamaged. Do not use damaged or defective
parts. If you require replacement parts, contact customer service at
[email protected].
• Not all parts and hardware included will be used.
• Do not use this product for any purpose or in any configuration not explicitly
specified in this instruction. We hereby disclaim any liability for injury or damage
arising from incorrect assembly, incorrect mounting, or incorrect use of this
product.
A(x1)
CPU Holder
B(x4)
st4.8x16mm
Screw
C(x4)
st4.8x38mm
Screw
D(x4)
Anchor
E(x12)
Pad
F(x4)
Washer
G(x1)
Allen Key
Note:
Only used for concrete block wall
Pencil
Drill 1/8 in.(3 mm)
Wood Drill 1/4 in.(6 mm)
Concrete Drill
Phillips Screwdriver

2
Step 2 Adjust the Height of the CPU Holder [A]
CAUTION: TO AVOID ANY DAMAGES, PLEASE TAKE OFF CPU
BEFORE MAKING HEIGHT ADJUSTMENT
Step 1 Attach the Pads [E] to the CPU Holder [A]
A
H1
H2
1. Loosen the preassembled bolt [H1].
2. Pull out and hold the bolt [H2].
3. Adjust the height of the CPU holder [A].

Step 3a For Desk Installation Option
Step 3 Secure CPU Holder
Secure CPU Holder [A] to the Bottom of Desk Using Screws [B]
and Washers [F]
4. Fasten the bolt [H1] and release the bolt [H2] to fix the CPU holder [A] in
place
3
H2
H1
A
Note: the height of CPU holder [A] should be greater
or equal to that of CPU

Step 3b For Wood Stud Installation Option
4
Step 3b-1 Position the CPU
holder [A] at your desired
height. Level the CPU holder
and mark the four holes.
Step 3b-2 Drill 4 pilot holes using a
1/8 in.(3 mm) diameter drill bit. Make sure
the depth is not less than 0.6 in.(15mm).
Secure the two screws [B] into the two top
holes.
Step 3b-4 Secure the CPU
holder [A] using the other
two screws [B]
Step 3b-3 Hang the CPU holder [A]
to the screws [B]
1/8 in.(3 mm) spacing left
[Not Included]
[Not Included]
A
1/8 in.
(ø3 mm)
0.6 in.(15 mm)
Note: Do not use wall anchor for
wood stud installation

Step 3c For Concrete Wall Installation Option
[Not Included]
5
Step 3c-1 Position the CPU holder [A]
at your desired height. Level the CPU
holder and mark the four holes.
Step 3c-2 Drill 4 pilot holes using a 1/4
in.(6 mm) diameter drill bit. Make sure the
depth is not less than 1.6 in.(40 mm). Knock
anchors [D] into the wall. Secure the two
screws [C] into the top two anchors [D].
Step 3c-4 Secure the CPU holder [A]
to the concrete wall using the other
two screws [C]
Step 3c-3 Hang the
CPU holder [A] to the
screws [C]
1/4 in.
(ø6 mm)
1.6 in.(40 mm) Note: Be sure the anchors [D] are
seated flush with the concrete
surface.
[Not Included]
1/8 in.(3 mm) spacing left
A

Step 4-2
Step 4 Put CPU into the CPU Holder
Step 4-1 Loosen the Knobs [K] to Increase the Width of the CPU Holder [A],
Then Put CPU into the CPU Holder [A]
K
Adjust the Width of CPU Holder [A] According to the Width of CPU,
Then Tighten the Knobs [K]
6
K

Thank you again for
choosing this HUANUO product!
All of us at HUANUO do appreciate your product purchase. We hope
that you are as happy with your product as we designing and
manufacturing it for you. We strive to provide you with the best
quality products and services in the industry. Please share your
experience of our product with others at
www.huanuoav.com/reviews if you are satisfied. If you have any
questions please don't hesitate to contact us at
Technical Support:
1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA)
Please check
www.huanuoav.com
for more products and
company information.