HUANUO HACM1 User manual

Monitor Table Stand
Instruction Manual
Model: HACM1
1
Thank you for choosing this huanuoav product! At huanuoav we
strive to provide you with the best quality products and services in
the industry. Should you have any issues, please don't hesitate to
contact us at
[email protected] (US/CA/DE/UK/FR/IT/ES/AU)

Supplied Parts and Hardware
X1
05 X4 06
UNPACKING INSTRUCTIONS AND IMPORTANT SAFETY INFORMATION
X1
01
X1
08
X1
07
Check the VESA Pattern of Monitor Before the Installation
Tools Required [Not Included]
If your TV VESA is greater than 100x100 mm/4 x 4 in. or less than VESA 75 x 75mm/3 x 3 in.,
this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
Minimum VESA Pattern: 3 in./75mm(W) x 3 in./75mm(H)
MAX:
100
mm/4 in.
MAX:
100
mm/4in.
100 mm ≈ 4 in.
75 mm ≈ 3 in.
Support Pillar X1
02
Base X1
03
Monitor Connector X2
04
Monitor Plate
Wire Clip Wire Clip Knob Grommet Plate
Drill(Optional)
Philips Screwdriver
•Carefully open the carton, remove contents and lay out on cardboard or other protective surface to
avoid damage.
•Check package contents against the Supplied Parts and Hardware List to assure that all components
were received undamaged. Do not use damaged or defective parts.
•Not all parts and hardware included will be used. lf you require replacement parts, contact customer
service at [email protected]
•Carefully read all instructions before attempting installation.
•If you do not understand the instructions or have any concerns or questions, please contact customer
service at [email protected]
•This product may contain moving parts. Use with caution.
•Do not use this product for any purpose or in any configuration not explicitly specified in this
instruction. We hereby disclaim any liability for injury or damage arising from incorrect assembly,
incorrect mounting, or incorrect use of this product.

φ 3/8 in.（10mm）
Bolt
M4x12mm
M-A X8
Bolt
M4x16mm
M-B X8
Bolt
M5x12mm
M-C X8
Bolt
M5x16mm
M-D X8
D5
Washer
M-E X8
Spacer
M-F X8
X1
C
5/32 in.(4mm)
Allen Key X1
D
15/64 in.(6mm)
Allen Key
X3
A
Bolt M5x18mm
X2
B
Bolt
M3x8mm
Nut
01
02
08
07 D
Step 1 Connect the Support Pillar Assembly to the Desktop
01
02
A
C
Step 1-1
Step 1-2
Note: If there isn’t a hole on your desk, you
can use a 0.47 in.-1.18 in.(12 mm-30mm)
drill to drill a hole. The drill is NOT included.

Allen Key [D]
15/64 in.(6mm)
Step 2-1
Step 2-2
Step 2
06
Connect Cable Clip [05] and Monitor Connector [03] to the
Support Pillar [01]
D
05
03 01
03 01

M5M4
Only one bolt size fits your monitor.
Step 3 Select Monitor Bolts
04
M-A/M-C
M-E
M-B/M-D
M-E
M-F
FLAT BACK MONITOR
(UNIVERSAL MONITOR PLATE)
CURVED BACK MONITOR
(UNIVERSAL MONITOR PLATE)
Step 4 Attach the Monitor Plates [04] to the Monitors
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the monitor.
-Too long will damage the monitor.
Too Short Too Long Correct Correct

Allen Key [D]
15/64 in.(6mm)
B
Step 5
Step 6 Fix Tilt Angle of the Monitors
Secure Monitors to the Stand Using Nuts and Bolts [B]
D
B

Manage the Cables
Step 7
Step 8
D15/64 in.(6mm)
5/32 in.(4mm)
Store Allen Keys into the Cable Clip
C

Features
360°
360°
180°
Tilt Tilt
Individual VESA plate height
adjustment helps monitors to be
perfectly aligned.
Note: Please make sure two arms are aligned and balanced.
D