HUANUO HNCM7 User manual

Desk Monitor Arm
INSTRUCTION
MANUAL
Rev00(A)
HNCM7
(US/CA) 1-800-556-0533
(UK) 44-808-196-3874
[email protected]
WWW. www.huanuo.com
02 03 04
05 06 07 08
09 10 11
12 13 14 15
16 17 18 19
20 21 22

17.6 lbs /
8kg
Before getting started,
let's make sure this mount is compatible.
Is the VESA
pattern of your
monitor 75 x 75mm
(3″ x 3″) to 100 x
100mm (3.9″ x 3.9″)?
Does your monitor
(including accessories)
weigh less than 17.6 lbs
(8kg) ?
Tools Needed
(NOT lncluded)
Yes - Perfect!
No - This mount is NOT
compatible.
Yes - Perfect!
No -This mount is NOT
compatible.
1
2
3
4
7/16 - 7/8″
(11 - 22mm)
Wood Drill Bit
W
H
3/8″ (10mm)
Wrench
Electric Drill
Phillips
Screwdriver
Important Safety
Information
· Avoid potential personal injuries and property damage!
· DO NOT use this product on desks made of particle board or other
soft woods.
· DO NOT use this product for any purpose that is NOT explicitly
specified in this manual. DO NOT exceed weight capacity. We are
NOT liable for damage or injury caused by improper mounting,
incorrect assembly or inappropriate use.
· Before starting assembly, verify all parts are included and
undamaged. DO NOT use damaged or defective parts. lf you require
replacement parts, please contact our technical support line at
1-800-556-0533 (US/CA) / 44-808-196-3874 (UK) or customer
service at [email protected].
· This product contains small parts that may pose a choking hazard.
4
NOTE
CAUTION
WARNING
· Please carefully read all instructions before attempting installation.
If you DO NOT understand the instructions or have any questions or
concerns, please contact our technical support line at
1-800-556-0533 (US/CA) / 44-808-196-3874 (UK) or customer
service at [email protected].
· Not all hardware included in this package will be used.
02 03 04
05 06 07 08
09 10 11
12 13 14 15
16 17 18 19
20 21 22

JP
Contents
Locking Plate
[a] x 1 Bottom Pad [b] x 1
M8
Nut
[E2] x 1
M6
Nut
[E3] x 2
3/16″ (5mm)
Large Allen Key
[F1] x 1
1/8″ (3mm）
Small Allen Key
[F2] x 1
M4 x 12mm
Bolt
[A] x 8
M4 x 30mm
Bolt
[B] x 8
L13mm
Spacer
[C] x 8
M4
Washer
[D1] x 8
M8 X 8mm
Bolt
[E1] x 2
x 1
01
Pole
x 1
02
C-Clamp
Decorative Cover
[D2] x 1
x 1
03
Swivel Arm
x 2
04
VESA Plate
02 03 04
05 06 07 08
09 10 11
12 13 14 15
16 17 18 19
20 21 22

Option A: For C Clamp Mounting
Step 1 Install the Base
E1
F2
01
b
02
0.4″- 3″
(10mm - 78mm)
a
02 03 04
05 06 07 08
09 10 11
12 13 14 15
16 17 18 19
20 21 22

Option B: For Grommet Mounting
a
b
b
02
01
02a
a
E2
01
02a
NOTE: If there is no grommet hole on your desktop, mark a hole on your desired position
(Be sure to leave 2″ from the edge of the desktop). Drill a hole using a drill bit in the
diameter of 7/16-7/8″ (11-22mm).
≥2″ (50mm)
7/16 - 7/8″
(11 - 22mm)
7/16 - 7/8″
(11 - 22mm)
Remove the pre-assembled washer and bolt on the locking plate [a].
Phillips
Screwdriver
(Not lncluded)
Electric Drill
(Not lncluded)
0.4″- 3″
(10mm - 78mm)
02 03 04
05 06 07 08
09 10 11
12 13 14 15
16 17 18 19
20 21 22

Step 2 Secure the Swivel Arm [03] and Decorative Cover [D2] to
the Pole [01]
D2
01
03
WARNING
CASE：If the head
is not straight.
Solution
F1
Height Adjustment
① ② ③
NOTE: The bolt
should be directed
toward the top.
Slide the swivel extension arm [03] downwards to your desired height, and tighten the
nuts [F1] to hold the arm in place.
02 03 04
05 06 07 08
09 10 11
12 13 14 15
16 17 18 19
20 21 22

Select Monitor Bolts
Step 3 Attach the VESA Plates to the Monitors
Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt
(M4 x 12mm or M4 x 30mm) to use. A minimum of 4-5 turns into the threading is required.
Do not turn past the bottom of the hole.
Option A (For Flat Back TVs)
A
D1
04
M4 x 12mm
M4 x 30mm
02 03 04
05 06 07 08
09 10 11
12 13 14 15
16 17 18 19
20 21 22

Option B (For Curved TVs)
E3
Step 4 Hang the Monitors on the Swivel Arm
B
D1
04
C
3/8″ (10mm)
Wrench
(Not lncluded)
Hang the monitor on te head of the swivel arm using the hanging tab and nut [E3].
Tighten the nut [E3]. Make sure the nut is secured before you rotate the monitor.
02 03 04
05 06 07 08
09 10 11
12 13 14 15
16 17 18 19
20 21 22

Step 5 Alignment of Two Monitors
Remove the nut [E3] with wrench, then turn the bolt with small Allen key [F2] to raise
or lower the monitor. Then retighten the nut [E3] after adjustment. Individual monitor
height adjustment helps to perfectly align the monitors.
3/8″ (10mm)
Wrench
(Not lncluded)
NOTE: Ignore this step
if monitors are level.
F2
E3
Loosen Tighten
02 03 04
05 06 07 08
09 10 11
12 13 14 15
16 17 18 19
20 21 22

TiltTilt
The monitor should adjust easily when moved, then stay in place. Adjust the tilt tension
bolt [T] if your monitor naturally tilts up or down.
Step 6 Tilt Adjustment
T
Loosen
Tighten
F1
02 03 04
05 06 07 08
09 10 11
12 13 14 15
16 17 18 19
20 21 22

WARNING:
To avoid tipping, please be careful not to extend the arms too far forward or backward.
When you adjust the angle of the arms, please make sure two arms are balanced to
avoid instability of the center of gravity of the base.
Swivel Swivel Swivel
Swivel Swivel
Cable Tie x 6
NOTE:
You can rotate the monitor or
swivel the arm manually.
Step 7 Cable Management
Step 8 Rotation Restriction
WARNING: Ensure the monitor bolts and bolts securing the monitors to the mount are
fully tightened before rotation.
02 03 04
05 06 07 08
09 10 11
12 13 14 15
16 17 18 19
20 21 22

860-00889-00 Rev00
(US/CA) 1-800-556-0533
(UK) 44-808-196-3874
[email protected]
www.huanuo.com
WWW.
02 03 04
05 06 07 08
09 10 11
12 13 14 15
16 17 18 19
20 21 22