HUANUO HNWSS4 User manual

English --------------------------------- 01-11
Deutsch --------------------------------- 12-22
Français --------------------------------- 23-33
Español --------------------------------- 34-44
Italiano --------------------------------- 45-55
Model: HNWSS4
V3.0
Monitor Wall Mount
Instruction Manual
Thank you for choosing this HUANUO product! At HUANUO we strive
to provide you with the best quality products and services in the
industry. Please share your experience of our product with others at
www.huanuoav.com/reviews if you are satisfied. Should you have any
issues, please don't hesitate to contact us.
Technical Support:
1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info: [email protected] (US/CA)
[email protected](DE/UK/FR/IT/ES/NL/SE/AU)
Website:
www.huanuoav.com

Important Safty Information
Please carefully read all manual before use the product. If you do not under-
stand the manual or have any concerns or questions about the safety of the
use, please contact our Technical Support line at 1-800-556-0533 or cus-
tomer service at [email protected].
• Check package contents against Supplied Parts and Hardware List to assure
that all components were received undamaged. Do not use damaged or
defective parts. lf you require replacement parts, please contact our Technical
Support line at 1-800-556-0533 or customer service at
[email protected].
• Not all parts and hardware included will be used.
• This product is designed for use in wood stud, solid concrete, concrete
block and brick walls. - DO NOT install into drywall alone.
• For safe installation, the wall you are mounting to must be capable of
supporting minimum 4 times the weight of the total load (the mount, the
monitor and all accessories weight). If not, the surface must be reinforced to
meet this standard. The installer is responsible for verifying that the wall
structure/surface will safely support the total load.
• Do not use this product for any purpose or in any configuration not explicitly
specified in this instruction. We hereby disclaim any liability for injury or
damage arising from incorrect assembly, incorrect mounting, or incorrect use
of this product.
• This product contains a high pressure gas spring, fire and percussion
prohibited. Also it is strictly prohibited to dismantle without professionals.
Please return to the manufacturer or hand over to professional agencies if the
product is abandoned.
Check the VESA Pattern of Your TV before You Begin the Installation
100 mm ≈ 4 in.
200 mm ≈ 8 in.
75 mm ≈ 3 in.
Minimum VESA pattern: 75mm/3 in.(W)x75mm/3 in.(H)
MAX:200mm/8 in.
MAX:200mm/8 in.
If your TV VESA is greater than 200x200 mm/8x8 in. or less than VESA
75x75mm/3x3in., this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
01 02 03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33
34 35 36 37 38 39 40 41 42 43 44
45 46 47 48 49 50 51 52 53 54 55

Warning!
Do not adjust tension without monitor.
1. Ensure monitor has been attached to the mount.
2. Read your monitor box or manual to find out monitor net weight.
3. Ensure the net weight of monitor (including accessories) is between
6.6~26.4 Ibs (3-12 kg).
Clockwise to reduce
tension(carry less weight)
Counter-clockwise to increase
tension(carry more weight)
TENSION ADJUSTMENT SHOULD BE DONE ONLY
AFTER MOUNT INSTALLATION
Adjustment Sign
01 02 03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33
34 35 36 37 38 39 40 41 42 43 44
45 46 47 48 49 50 51 52 53 54 55

Arm Assembly [01]
M4x25mm
Bolt A (x4)
M5x25mm
Bolt B (x4) M6x25mm
Bolt C (x4)
Allen Key J (x1)
M5
M6x6mm
Bolt D (x4)
Sleeve G (x1)
10-12mm
Lag Screw H (x2)
Decorative Cover K (x2)
Monitor Bracket [02]
M6x60mm
Washer E (x2)
φ16xφ6.2xφ1.5
Spacer F (x4)
φ15xφ8.2x10
Wall Anchor I (x2)
10-50
Screwdriver
Tools Needed (Not lncluded)
Pencil
Drill
Stud Finder Level
Parts and Hardware List
5/32 in.(4mm)
Wood Drill
3/8 in.(10mm)
Concrete Drill
01 02 03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33
34 35 36 37 38 39 40 41 42 43 44
45 46 47 48 49 50 51 52 53 54 55

Position the arm assembly [01] at your desired height, level the arm assembly [01]
and mark the pilot hole locations
X X
√
3
1a-1
1a-2
1
Note： Do not use wall anchors for this step!
21
HE
JG
G
J
1a. Wood Stud Option
[01]
Drill 2 pilot holes using a 5/32 in. (4mm) diameter drill bit. Make sure the depth is not
less than 2 23/64 in. (60mm). Install the arm assembly [01] using lag screws [H] and
washers [E].
(Not Included) ø5/32 in. (4mm)
ø2 23/64 in. (60mm)
01 02 03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33
34 35 36 37 38 39 40 41 42 43 44
45 46 47 48 49 50 51 52 53 54 55

1b-1
1b-2
1
X X
√
2
Position the arm assembly [01] at your desired height, level the arm
assembly [01] and mark the pilot hole locations.
H
[01]
E
JG
I
G
J
1b. Solid Concrete or Concrete Block Option
Never drill into
the mortar
between blocks.
Drill 2 pilot holes using a 3/8 in.(10mm) diameter drill bit. Make sure the depth is not
less than 2 9/16 in.(65mm). Install the arm assembly [01] using lag screws [H],washers
[E] and anchors [I]
Note：Be sure the anchors [I] are seated
flush with the concrete surface.
(Not Included) ø3/8 in.(10mm)
2 9/16 in.(65mm)
01 02 03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33
34 35 36 37 38 39 40 41 42 43 44
45 46 47 48 49 50 51 52 53 54 55

[01]
2. Attach the Decorative Covers [K] to Arm Assembly [01]
K
M5M4 M6
Only one bolt size fits your monitor.
3. Secure the Monitor Brackets [02] to Monitor
Select Monitor Bolts
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the Monitor.
-Too long will damage the Monitor.
Note: If necessary, the spacers can be used. If the installation fails
after trying various methods, please contact customer service at
[email protected]
A B C
Too Short Too Long Correct Correct
01 02 03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33
34 35 36 37 38 39 40 41 42 43 44
45 46 47 48 49 50 51 52 53 54 55

Secure two pcs bolts into the top
VESA holes on the back of the monitor
manually.
4x4 in.(100x100mm)
A/B/C
The tension is preset at 8.8-11lb
(4-5kg). After hanging the monitor to the
mount, please release the monitor slowly
to prevent it from falling suddenly.
Option A： No Need to Attach Monitor Brackets [02] to Monitor
Please keep about 0.2 in.( 5mm)
spacing left for the two bolts.
Hang the monitor with two bolts
onto the arm assembly [01]
Secure the monitor to arm assembly
[01] by screwing the other 2 pcs bolts.
3A-2
3A-3
3A-4
3A-1
3x3 in.(75x75mm)
3 in. (75mm)x3 in. (75mm)
4 in.(100mm)x4 in.(100mm)
Screwdriver
Screwdriver
0.2 in.(5mm) spacing left
01 02 03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33
34 35 36 37 38 39 40 41 42 43 44
45 46 47 48 49 50 51 52 53 54 55

Hang the monitor with monitor
brackets [02] onto the arm assembly
[01]
3B-1
3B-2
The tension is preset at 8.8-11lb
(4-5kg). After hanging the monitor to the
mount, please release the monitor slowly
to prevent it from falling suddenly.
Option B：Need to Attach Monitor Brackets [02] to Monitor
0.1in. (2.5mm) spacing left
D
3B-3
Secure the monitor to arm assembly [01]
by tighting all the four pcs bolts [D].
3B-4
Thread 2 pcs bolts [D] to the holes in the
middle of the upper monitor bracket [02].
Please keep about 0.1 in. (2.5mm)
spacing left for the bolts.
8in.(200mm)x4 in.(100mm)
8 in.(200mm)x8 in.(200mm)
Secure monitor brackets [02] to
monitor using 4 pcs bolts(A/B/C)
manually. If necessary, the spacers
[F] can be used.
D
[02]
F
4 in.(100mm)
8 in.(200mm)
Screwdriver
Screwdriver
01 02 03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33
34 35 36 37 38 39 40 41 42 43 44
45 46 47 48 49 50 51 52 53 54 55

Be sure to keep the arm in
horizontal position during
adjustment. Or else, it would
be difficult to adjust the
mount or damage the mount.
1. If the monitor can stay at the desired
height by itself, no adjustment needed.
2. If the monitor rises up, press the arm to
keep it in horizontal position and then use
the 5mm Alley key [J] to turn the bolt
clockwise(“-” direction) to reduce tension
of the arm only until the monitor can stay
at the desired height by itself.
3. If the monitor falls down, lift the arm to
keep it in horizontal position and then use
the 5mm Alley key [J] to turn the bolt
counter-clockwise(“+” direction) to
increase tension of the arm only until the
monitor can stay at the desired height by
itself.
4. Adjust Gas Spring Tension
(1 rotation ≈ 1 lb)
(5mm)
J
01 02 03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33
34 35 36 37 38 39 40 41 42 43 44
45 46 47 48 49 50 51 52 53 54 55