HUANUO HNCM12-1 User manual

Model: HNCM12-1
Thank you for choosing this HUANUO product! At HUANUO we strive to
provide you with the best quality products and services in the industry.
Should you have any issues, please don't hesitate to contact us at
Technical Support:
1-800-556-0533 Mon-Fri 8am - 8pm (CST)
Other Info:
[email protected] (US/CA)
V3.0
Monitor Desk Mount Instruction Manual

Tools Needed (Not Included)
Phillips Screwdriver
Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact
our Technical Support line at 1-800-556-0533 or customer service at sup-
[email protected].
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• The desk must be capable of supporting five times the weight of the monitor
and mount combined.
Check the VESA Pattern of Your Monitor before the Installation
IMPORTANT SAFETY INFORMATION
If your monitor VESA is greater than 200x200 mm/8x8 in or less than
VESA 75x75mm/3x3 in, this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
MAX: 200mm/8 in
MAX: 200mm/8 in
Minimum VESA pattern:
75mm/3 in (W)x75mm/3 in (H)
100 mm ≈ 4 in
75 mm ≈ 3 in
200 mm ≈ 7 7/8 in
010101
3/8 in (10mm)
Socket Wrench
Drill(Optional)
7/16 in (11mm) -
55/64 in (22mm)
Drill(Optional)

Washer
M10
D1 (x1)
Nut
M10
D2 (x1)
Bolt
M6X12MM
D3(x1)
13/64 in (5mm)
Large Allen Key
F1 (x1)
5/32 in (4mm）
Small Allen Key
F2 (x1)
Locking Plate
b (x1)
C-Clamp Brace
02 (x1)
C-Clamp
03 (x1)
Pole
01 (x1)
Bottom Pad
c (x1)
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware
Warning: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use dam-
aged or defective parts. lf you require replacement parts, please contact our Technical
Support line at 1-800-556-0533 or customer service at [email protected].
• Please note: Not all hardware included in this package will be used.
Supplied Parts and Hardware for Step 2
Decorative Cover
a (x1)
Monitor Connector
04 (x1)
Supplied Parts and Hardware for Step 3
Extender Bracket
06 (x4) Nut F5 (x4)
Bolt
F4 (x4)
Faceplate
05 (x1)
02
Bolt
M8X10MM
E1 (x2)
Bolt
M6X8MM
F3 (x2)
Washer
M6
E2 (x1)

Bolt
M4X12MM
A1(x4)
Bolt
M4X16MM
A2(x4)
F (x1)
Bolt
M6X15MM
Spacer
5mm
C2 (x8)
Supplied Hardware for Step 4
Supplied Hardware for Step 5
03
Bolt
M5X15MM
B1(x4)
Bolt
M6X15MM
B2(x4)
Washer
M6
C1 (x4)
Step 1 Install the Base
Option A：
C-Clamp Installation
02
01
Small
Allen Key
F2
F3
D3
Small
Allen Key
F2
b

04
03
02
E2
a
03
Large
Allen Key
E1
F1
DeskDesk DeskDesk
Tighten
Desk
Thickness
2 11/64 in (55mm) - 3 5/32 in (80mm)
Desk
Thickness
1 3/16 in (30mm) - 2 11/64 in (55mm)
Desk
Thickness
3/8 in (10mm) - 1 3/16 in (30mm)

05
b
Option B:
Grommet Installation
b
03a 03b
03b
If there is no grommet hole on your desk,
position the pole [01] on the mounting
surface and mark the hole. Drill a hole
using the drill bit in a diameter of
7/16 in - 55/64 in (11-22mm) at the
marked position through the mounting
surface.
01
Step 2 Secure Monitor Connector and Decorative Cover to Pole Assembly
F1
Large Allen Key
Tighten
04
a04
DeskDesk DeskDesk
a
03b
25/32 in - 3 5/32 in
(20-80mm)
7/16 in - 55/64 in
(11-22mm)
D1
D2

For VESA hole pattern:
8x8 in (200x200mm) For VESA hole pattern: 8x4 in (200x100mm)
Option B Need to Attach Extender Brackets [06] to Faceplate [05]
200 mm
200 mm
200 mm
100 mm
Phillips
Screwdriver
(Not Included)
Attach Faceplate（or Faceplate with Extender Bracekts）
to the Back of Monitor
F4
F5
3/8 in (10mm)
Socket Wrench
（not included)
05
06
06
Step 4
C2
(If Needed)
C1
A1/A2/B1/B2
C2
(If Needed)
C1
A1/A2
/B1/B2
Or
Step 3
Choose the Combination that Applies to Your VESA Hole
Pattern
100 mm
75 mm
100 mm
75 mm For VESA hole pattern:
3x3 in (75x75mm)
4x4 in (100x100mm)
Option A No Need to Attach Extender Brackets [06] to Faceplate [05]
UP

07
Step 5 Hang the Monitor to the Stand
Step 6 Adjust the Tilt Angle and Manage the Cables
F
F2
Small Allen Key
Warning:
To avoid tipping, please be careful not to extend the monitor too far
backward. When you adjust the angle of the monitor, please make
sure the monitor is balanced to avoid instability of the center of
gravity of the base.
HEAVY! You may need
assistance with this step.
DeskDesk
2X Cable tie
Tilt Adjustment
Tilt Adjustment
F1
T
Large Allen Key
1. If the monitors can stay at the
desired height by itself, no
adjustment needed.
2. The tilt angle of the monitor
will not be adjusted if the set
screw [T] is over-tightened. In
this case, you need to turn the
set screw [T] in anti-clockwise
direction to decrease torque until
the monitors can be hovered at
any position.
3. The monitors will drops
automatically if the set screw [T]
is over-loosen. In this case, you
need to turn the set screw [T] in
clockwise direction to increase
torque until the monitors can be
hovered at any position.