HUANUO HNCM2 User manual

Installation Instruction
V2.0
HNCM2 [email protected]

1
UNPACKING INSTRUCTIONS
Carefully open the carton, remove contents and lay out on cardboard or other protective
surface to avoid damage.
Check package contents against the Supplied Parts List in the next page to assure that
all components were received undamaged. Do not use damaged or defective parts.
Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
Install and operate this device with care. Please read this instruction before installation,
and carefully follow all instructions contained herein. Use proper safety equipment during
installation.
Please call a qualified installation contractor for help if you don't understand these
directions or have any doubts about the safety of the installation.
Do not use this product for any purpose or in any configuration not explicitly specified in this
instruction. We hereby disclaims any and all liability for injury or damage arising from
incorrect assembly, incorrect mounting, or incorrect use of this product.
!
!
!
!
!

2
Supplied Parts List
Not Included Phillips Screwdriver
Swivel Arms
d (x2)
Pole
a (x1)
“C” Clamp
b (x1)
“C” Clamp Brace
c (x1)
Nut
h (x2)
VESA Plate
e (x2)
M5x14 Bolt
f (x3)
M8x12 Bolt
g (x2)
Spring Washer
l (x1)
M10 Bolt
i (x1)
Support Plate
j (x1)
M10 Washer
k (x1)
Allen Key
o (x1)
Grommet Base Plate
m (x1)
Wire Clip
n1 (x1)
Wire Clip
n2 (x4)
M4 Spacer
s (x8)
Wrench
p (x1)
M4x12 Thumb Bolt
q (x8)
M4x30 Bolt
r (x8)
Laptop Tray
t (x1)
M4x10 Bolt
u (x4)
M4 Nut
v (x4)

3
Step 1 Install the Pole to the Desktop
Option B: Grommet Base Assembly a
Figure 3
m
f
Figure 4
j
i
p
k
l
Option A：Desk Clamp Assembly a
Figure 1
f
c
Figure 2
g
o
b
Plastic Knob
1.Use 3 pieces M5x14 bolts(f) to install the C Clamp
brace(c) to the Pole. Use the Allen Key(o) to tighten
the bolts. See Figure 1.
2.According to the thickness of the desktop, Use 2
pieces M8x12 bolts(g) to install the C clamp(b) to C
clamp brace (c). Use Allen Key(o) to tighten the bolts
and then tighten the C clamp to the desktop by
adjusting the plastic knob. See Figure 2.
Existing Grommet Hole Installation
If the existing grommet hole comes with a plastic
protector, remove it to ensure a flat surface
before installing the desk mount
1.Use 3 pieces M5x14 bolts(f) to install Grommet
Base Plate(m) to the Pole(a). Use the Allen Key
to tighten the bolts. See Figure 3.
2.Position the Pole(a) on the mounting surface
and under the desktop comes the Support Plate
(j), M10 Washer(k), Spring Washer (l). Use the
provided Wrench(p) to fasten the M10 Bolt. See
Figure 4.
o
o

j
i
p
k
l
4
Step 1 Install the Pole to the Desktop
Step 2 Install Arm to the Pole
Option B: Grommet Base Assembly a
Figure 5
Figure 6
m
f
Existing Grommet Hole Installation
1. Position the Pole(a) on the mounting surface
and mark the center hole. Drill a 3/8" (10mm)
diameter hole at the marked position through the
mounting surface.
2.Use 3 pieces M5x14 Bolts(f) to install the
Grommet Base Plate(m) to the Pole(a). Use the
Allen Key(o) to tighten the bolts. See Figure 5.
3.Position the Pole(a) on the mounting surface
and under the desktop comes the Support Plate
(j), M10 Washer(k), Spring Washer (l). Use the
provided Wrench(p) to fasten the M10 Bolt. See
Figure 6.
Install Swivel Arms(d) to the Pole(a). Fasten the
bolt with supplied Allen Key(o). Attach the Wire
Clip(n1,n2) to the Pole(a) and Swivel Arms(d). d
o
n1
n2
d
o

5
Step 3 Attach the VESA Plate to the Laptop Tray or Monitor
Step 4 Slide the Monitor onto the Head of Swivel Arm
h
s
r
t
u
v
q
For Laptop For Monitor with Flat Back For Monitor with Curved
or Recessed Back
Slide the monitor onto the head of Swivel
Arm(d) as shown in the above diagram.
Install the security Nut(h). Make sure the
security nut is installed before you rotate the
monitor.

6
Step 5 Make the Necessary Adjustments
Step 6 Manage the Wires and Store the Allen Keys on Wire Clip
o
o
Fix the tilt angle
Tighten the bolt with the supplied Allen Key(o) to
fix the tilt angle.
Use the supplied Allen Key(o) to make the
necessary adjustments.

7
Step 7 All Done
413mm(16.3inch)
78mm(3.1inch)
93mm(3.7inch)
0-100mm(0-4inch)
425mm(16.7inch)
355mm(14inch)
300mm(11.9inch)
75-100mm(3-4inch)
75-100mm(3-4inch)
Thank you for choosing our product! We strive to provide the best quality and
services for our customers. Would you kindly share your experience on Amazon if
you are satisfied? Should you have any issues, please don't hesitate to contact us.
Telephone：[phone]
Mon-Fri 10am - 6pm (PST) (USA)
Email：[email protected]
(US/CA/DE/UK/FR/IT/ES/JP/AU)