HUANUO HNTS3S User manual

HNTS3S/HNTS3B/HNTS3W
INSTRUCTION
MANUAL
Rev01(A)
(US/CA) 1-800-556-0533
(UK) 44-808-196-3874 [email protected]
www.huanuoav.com
WWW.
Desk Monitor Arm

IMPORTANT SAFETY INFORMATION
Weight Restrictions
18 lbs
(8 kg)
If your monitor weighs
more than the weight
above, the mount is
NOT compatible.
Monitor should not
exceed weight capacity.
WARNING
DO NOT exceed the maximum weight indicated. This mounting
system is intended for use only within the weight range listed.
Exceeding the maximum weight limit may result in failure of
the mount, causing potential damage and/or injury.
It is the responsibility of the installer to verify the total weight
of the monitor and any accessories attached.
• Please carefully read all instructions before attempting installation. If you do not understand the
instructions or have any questions or concerns, please contact our Technical Support at
1-800-556-0533 (US/CA) / 44-808-196-3874 (UK) or Customer Service at [email protected].
CAUTION: Avoid potential injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
• This product contains gas spring arms which are under high pressure. Do not puncture these arms or
expose the arms to fire or flame. If product is defective, please contact our Technical Support at
1-800-556-0533 (US/CA) / 44-808-196-3874 (UK) or Customer Service at [email protected].
• Do not use this product on desks made of particle board or other soft woods.
• The information contained in this manual does not cover all possible conditions or variables in
relation to the installation of this product.
Check the VESA Pattern of Your Monitor BeforeInstallation
If your monitor's VESA pattern is smaller than 75mm x 75mm / 3″ x 3″ or greater than
100mm x 100mm / 3.9″ x 3.9″, this mount is NOT COMPATIBLE. Please contact our
Technical Support at 1-800-556-0533 (US/CA) / 44-808-196-3874 (UK) or
Customer Service at [email protected] to find a compatible product.
Minimum: 75mm x 75mm / 3″ x 3″ (W x H)
Maximum: 100mm x 100mm / 3.9″ x 3.9″ (W x H)
Measure Your Monitor's VESA Pattern:
MAX: 100mm/3.9″
MAX: 100mm/3.9″
0202

Product Features
180°
360°360°360°
C-Clamp Mounting for table edge
0.39 - 3.15″ (10 - 80mm)
Grommet Mounting for grommet bolt
0.39 - 2.36″ (10 - 60mm)
26.18″
(665mm)
360°
03
+20°/ -20°
+85°/ -90°

04
DO NOT adjust tension without monitor attached.
1. Verify the weight of your monitor (including accessories) is less than
18 lbs (8 kg).
2. Monitor weight can be found in manual or on manufacturer's website.
3. Ensure monitor has been securely attached to the mount.
TENSION ADJUSTMENT SHOULD ONLY BE
PERFORMED AFTER MONITOR INSTALLATION
Attention
WARNING:
• Gas Spring Arm is under pressure and should be handled with care.
• Failure to follow the instructions may result in damage to the mount
and/or personal injury.

05
Supplied Parts and Hardware
Supplied Parts and Hardware for Step 1
Tools Needed (Not lncluded)
3/16″ (5mm)
Large Allen Key
J x 1
1/8″ (3mm)
Small Allen Key
H x 1
Base
R x 1
Pole
Q x 1 Base Plate
K x 1
5/32″ (4mm)
Medium Allen Key
I x 1
WARNING: This product contains small parts that may pose a choking hazard.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, please contact our Technical
Support at 1-800-556-0533 (US/CA) / 44-808-196-3874 (UK) or Customer Service at
[email protected].
• NOTE: Not all hardware included in this package will be used.
Tape Measure Drill (Optional) 7/16-7/8″ (11-22mm)
Drill Bit (Optional)
Supplied Parts and Hardware for Step 2
Arm Support
V x 1
Monitor Connector
T x 1 Extension Arm W x 4 Compression Arm U x 2
Cable Management Cover
X x 2
Decorative Cover
G x 6
Bolt
M5 x 6mm
E x 6
Set Screw (Spare)
M6 x 6mm
N x 2
NOTE: The set screws [N] are
spare screws which can be
used if the preassembled set
screws on the arms [W] and
compression arms [U] are
missing.
Phillips Screwdriver

06
Monitor Plate
S x 3
Bolt
M4 x 12mm
A x 13
Bolt
M6 x 8mm
L x 3
Bolt
M4 x 30mm
B x 13
Washer
10 x 4.3 x 1mm
C x 12
Spacer
10 x 5.2 x 13mm
D x 12
Hardware for Step 4
Supplied Parts and Hardware for Step 3
Hardware for Step 9
Cable Clip
F x 2
Q
H
1/8″ (3mm)
Option A：For Clamp Mounting
Step 1 Install the Base
Measure the thickness of the desk.
If the desk thickness is 0.98 - 3.15″ (25 - 80mm), skip this step and go to STEP A-1 and A-2.
If the desk thickness is 0.39 - 2.56″ (10 - 65mm), reinstall the C-Clamp as shown below.
A-1 Thread the pole [Q] into the
C-Clamp brace [R]. A-2 Tighten the knob against the desk to
mount the C-Clamp.
J
3/16″ (5mm)
R
J
3/16″ (5mm)

07
Option B：For Grommet Mounting
NOTE: If a hole is needed for grommet
installation, be sure to leave at least 2″
(50mm) from the edge of desktop and
mark where the hole will be drilled. Use
either a 7/16-7/8″ (11-22mm) drill bit
for this step.
7/16-7/8″
(11-22mm)
0.39-2.36″
(10-60mm)
2″ (50mm)
Drill
(Not Included)
7/16-7/8″
(11-22mm)
Drill Bit
(Not Included)
B-1 Detach the base [R] entirely. Keep the C-Clamp brace [a], locking plate [b] and
grommet bolt [c] for the use on PAGE 08.
a
Phillips
Screwdriver
(Not Included)
b
c
J
3/16″ (5mm)

08
3
B-2 Attach the base plate [K] to the bottom of base.
B-3 Thread the pole [Q] into the base.
B-4 Secure the pole assembly to the desktop by screwing grommet bolt [c] through
the desk and locking plate [b] and into the base.
d
K
I
5/32″ (4mm)
I
5/32″ (4mm)
d
c
b
Q
H
1/8″ (3mm)

09
The hanging tab
should face up.
Step 2 Secure the Arm Assembly to the Pole Assembly
2-2 Attach the two extension arms [W] onto the arm support [V].
2-1 Slightly loosen the set screw of arm support [V] and monitor connector [T]. Slide
them in sequence onto the pole at your desired height as shown. Reighten the set
screws to secure them.
W
V
T
V
T
V
G
G
G
H
1/8″ (3mm)
J
3/16″ (5mm)
J
3/16″ (5mm) J 3/16″ (5mm)
J
3/16″ (5mm)

10
2-3 Attach the cable management covers [X] to the compression arms [U].
2-4A If the monitors are 24″ or smaller, attach the compression arms [U] to the
extension arms [W].
2-4B If the monitors are larger than 24″, attach the other pair of extension arms [W]
between compression arms [U] and extension arms [W].
U
X
E
W
W
W
U
U
G
G
H
1/8″ (3mm)
H
1/8″ (3mm)