HUANUO HATS3 User manual

Model: HATS3
English ---------------------- 01-07
Deutsch ---------------------- 08-14
Français ---------------------- 15-21
Español ---------------------- 22-28
Italiano ---------------------- 29-35
Thank you for choosing this product!We strive to provide you with the best
quality products and services in the industry. Should you have any issues,
please don't hesitate to contact at
[email protected] (US/CA/DE/UK/FR/IT/ES/AU)
Gas Spring Aluminum LCD Monitor Desk
Instruction Manual V3.0

Weight Restrictions
Check the VESA Pattern of Monitor before the Installation
8 KG
(17.6 LBS)
DO NOT exceed the maximum weight indicated. This
mounting system is intended for use only within the
maximum weights indicated. Use with products heavier
than the maximum weights indicated may result in failure of
the mount and its accessories, causing possible injury.
WARNING:
If your monitor weighs more, this mount is NOT compatible.
MAX:100mm/4in.
MAX:100mm/4in.
100 mm ≈ 4 in.
75 mm ≈ 2 7/8 in.
Minimum VESA Pattern: 75mm/3 in.(W) x 75mm/3 in.(H)
• Please read through these instructions completely before attempting installation.
If you do not understand the instructions or have any concerns or questions, please
contact customer service at [email protected].
• Check package contents against Supplied Parts and Hardware List to assure that
all components were received undamaged. Do not use damaged or defective parts.
If you require replacement parts, contact customer service at
[email protected].
• Not all parts and hardware included will be used.
• This product contains a high pressure gas spring, fire and percussion prohibited.
Also it is strictly prohibited to dismantle without professionals. Please return to the
manufacturer or hand over to professional agencies if the product is abandoned.
• Do not use this product for any purpose or in any configuration not explicitly
specified in this instruction. We hereby disclaim any liability for injury or damage
arising from incorrect assembly, incorrect mounting, or incorrect use of this
product.
01

mm
Bolt
6
SUPPLIED PARTS AND HARDWARE
TOOLS REQUIRED NOT INCLUDED
12
mm
Bolt
12
mm
Bolt
12
mm
Bolt
6
mm
Bolt
12
Boltmm 2
Cable Clip
O (x2)
Locating Ring
P (x1)
Base Plate
Washer
mm
12 6
Decorative Cap
6
Hole Cover
1/8 in (3mm）
Small Allen key
5/32 in (4mm)
Medium Allen key 13/64 in (5mm)
Large Allen key
02
mm
Set Screw (Spare) Note: The set screws [N] are spare screws which
can be used if the preassembled set screws on the
arms [W] and compression arms [U] are missing.

Tighten the pole to the
base using 1/8 in(3mm)
small allen key [K].
1/8 in.
(3mm)
13/64 in.
(5mm)
3.
2-2. Connect the pole
[Q] to the base [R]
Step
A
Adjust the base according
to the thickness of desktop
2-1.1.
2.
Secure the base assembly to the desktop
For desktop with
thickness within
0.79-3.15 in.
(20-80 mm)
03
You can use the
Allen key to tighten
up
Recommened Desktop
Thickness:
0.79-3.15 in.
(20-80 mm)
Q
K
R

You can use the
Allen key to
tighten up
(20-70 mm)
5/32 in.
(4mm)
5/32 in.
(4mm)
Detach the base [R] entirely
3. Keep the rubber pad [e] and 4pcs
preassembled bolts for next step when
detaching the base
5. Install the pole assembly with bolt [d]
and clip plate [a] 6. Secure the pole assembly to the
desktop
1.
Attach rubber pad [e] to bottom plate.
2. Connect the
pole [Q] to the
desktop foot [b]
B
4.
04
Install base plate [P] and rubber
pad [e] to desktop foot with 4pcs bolts
Recommened Desktop
Thickness:
0.79-2.76 in.
13/64 in.
(5mm)
13/64 in.
(5mm)
R
M
Q
a
c
d
b
e
Le
a
d
P
L

Step 3-1 Slide the locating ring [O],
supporting part [V], locating ring [O] and
monitor in sequence to the pole
Height
Adjustment
Insert the bolts through
the washer and then put
on the decorative covers
ss
Step 3 Secure the Arm Assembly to the Pole Assembly
Step 2
When attaching brackets to the flat screen, be careful not to over tighten screws
and be sure that screws do not bottom out in the mounting holes.
Too LongToo Short
Step 3-2 Slide the two extension arms
[W] to the supporting part [V] and tighten
them using Allen key
05
Tighten
Tighten
Loosen
Loosen 1/8 in.
(3mm)
1/8 in.
(3mm)
S
T
S
TG
B/D
A/C
O
V
OK
W
V
K
I
H
J

If the monitors are 24in. or smaller
Secure the monitors to the compression
arms [U]
Attach the two compression arms [U] to
the two extension arms [W] and tighten
them using Allen key [K]
Attach the other two extension arms [W]
to the preassembled extension arms,
then attach the compression arms [U] to
the extension arms [W] and tighten them
using Allen key [K]
Secure the monitors to the compression
arms [U]
in.
Insert the bolts
through the washers
and then put on the
decorative covers.
06
Insert the screws through
the washers and then put
on the decorative covers.
1/8 in.
(3mm)
1/8 in.
(3mm)
U
W
U
W
I
H
J
K
U
KU
I
H
J

Store the Allen keys
into the cable clip
Attach the cable clips
[F] to the pole
Step 5 Route the Cables
Step 4
Gas Spring Adjustment
07
To ensure the swivel
function, please don’t
over-fasten the bolt
Secure the line hooks [X] to the
compression arms [U] , then
route the cables into line hooks
[X] on the compression arms [U]
and the line hooks preassembled
on the extension arms [W]
13/64 in.
(5mm)
1/8 in.
(3mm)
M
MM
K
M
X
E
F
K
L
M