HUANUO HNCM17 User manual

Model: HNCM17
Thank you for choosing this HUANUO product! At HUANUO we strive to
provide you with the best quality products and services in the industry.
Should you have any issues, please don't hesitate to contact us at
Technical Support:
(US/CA) 1-800-556-0533 Mon-Fri 8am - 8pm (CST)
(UK) 44-808-196-3874 Mon-Fri 2pm - 10pm (UTC)
Other Info:
[email protected] (US/CA)
[email protected] (DE/UK/FR/IT/ES/NL/SE/AU/PL)
V4.0(A)
Monitor Desk Mount Instruction Manual
English ------------------------------- 01-07
Deutsch ------------------------------- 08-14
Français ------------------------------- 15-21
Español ------------------------------- 22-28
Italiano ------------------------------- 29-35

01 02 03 04 05 06 07
IMPORTANT SAFETY INSTRUCTIONS
• Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact our
customer service at [email protected].
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We are not liable for damage or injury caused by
incorrect assembly or inappropriate use.
• The desk must be capable of supporting five times the weight of the monitor and
mount combined.
Check the VESA Pattern of Your Monitor beforethe Installation
If this desk mount is NOT compatible, please contact customer service
at [email protected] to find a compatible product.
If your monitor VESA is greater than 100x100 mm/4x4 in or less than
VESA 75x75mm/3x3in, this mount is NOT compatible.
75 mm ≈ 3 in
100 mm ≈ 4 in
Minimum VESA pattern:
75mm/3 in (W)x75mm/3 in (H)
MAX:100
mm/4 in.
MAX:100
mm/4 in
MAX:100
mm/4 in
Tools Need（Not Included）
Electric Drill
(Optional) 7/16 in (11mm) - 55/64 in (22mm) Drill Bit(Optional)
Phillips
Screwdriver
Weight Restrictions
DO NOT exceed the maximum weight indicated.This mounting
system is intended for use only within the maximum weights
indicated. Use with products heavier than the maximum weights
indicated may result in failure of the mount and its accessories,
causing possible damage and or injury.
WARNING
22.05 lbs.
(10 kg)
If your monitor weighs
more, this mount is NOT
compatible.
3/8 in (10mm)
Wrench

01 02 03 04 05 06 07
Large Allen Key
o (x1) Wire Clip
n1 (x1) Wire Clip n2 (x6)
Supplied Parts and Hardware for Step 2
VESA Plate
e (x3) M4x12mm Thumb Bolt
q (x8) M4 Spacer
s (x8)
M4x30mm Bolt
r (x8)
Laptop Tray
t (x1)
M4x10mm Bolt
u (x4) M4 Nut
v (x4)
Supplied Parts and Hardware for Step 3
Warning: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use damaged or
defective parts. lf you require replacement parts, contact customer service at
[email protected].
• Please note: Not all hardware included in this package will be used.
Supplied Parts and Hardware
Pole
a (x1) C Clamp Plate
b (x1) C Clamp Plate c (x1) M5x16mm Bolt
f (x3) M8x12mm Bolt
g (x2)
Medium Allen Key
o (x1) Small Allen Key o (x1) Bottom Pad w2 (x1)
Grommet Plate
m (x1)
Locking Plate
j (x1) Spring Washer l (x1)
M10 Washer
k (x1)
Supplied Parts and Hardware for Step 1
Bottom Pad
w1 (x1)
Swivel Arm
d (x1)

01 02 03 04 05 06 07
Step 1 Install the Pole to the Desktop
Option A: Desk Clamp Assembly
1A-1
1A-2
Nut
h (x3)
Supplied Hardware for Step 4
Supplied Hardware for Step 5
Medium Allen Key
o (x1)
c
b
g
o
Medium
Allen Key
OR b
a
c
f
w1
o
Small Allen Key
70mm
2 3/4 in 100mm
3 15/16 in
Desk

01 02 03 04 05 06 07
j
k
l
Phillips Screwdriver
Step 2 Install Swivel Arms to the Pole
Option B: Grommet Base Assembly
1. If the existing grommet hole comes with a plastic protector, remove it to ensure
a flat surface before installing the desk mount.
2. If there is no grommet hole on your desk, mark the pilot hole on your your
desired position. Drill a hole using the drill bit in a diameter of 7/16 in (11mm) -
55/64 in (22mm) at the marked position through the mounting surface.
Note:
a
f
m
w2
o
Small Allen Key
Install swivel arms (d) to the pole (a). Fasten the bolt with supplied Allen key (o).
Attach the wire clip (n1,n2) to the pole (a) and swivel arms (d).
d
o
n1
n2
d
UP
Phillips Screwdriver
(Not lncluded)
Applicable Desk
Thickness：70mm
a

01 02 03 04 05 06 07
Step 3 Attach the VESA Plate to the Laptop Tray or Monitor
For Laptop
For Monitor with Flat Back
For Monitor with Curved
or Recessed Back
q
r
s
e
t
u
v

01 02 03 04 05 06 07
Step 4 Secure the Monitor or Laptop Tray onto the Head of Swivel
Arm
h
4-1 Slide the monitor onto the head of
Swivel Arm (d) as shown in the above
diagram.
4-2 Secure the Nut (h). Make sure the nut
is installed before you rotate the monitor.
HEAVY! You may need
assistance with this step.
Step 5 Adjustment
1. Directly swivel your monitor to your desired
angle(if it is difficult to swivel the monitor, for
better to tilt Monitor you can slightly loosen
the nuts using the Allen key).
2. Tighten the nuts to hold the monitor in
place.
Swivel Adjustment
T
o
Medium
Allen Key
Tilt Adjustment
1. Directly tilt your Monitor to your desired
angle(if it is difficult to tilt the Monitor, for
better to tilt monitor you can slightly loosen
the nuts [T] using the Allen key).
2. Tighten the nuts [T] to hold the monitor in
place.
o
Medium
Allen Key
Note: Please refer the proce-
dures 4-1 and 4-2 to install
the laptop tray [t] with VESA
plate [e] onto the head of
swivel arm Wrench
3/8 in. (10mm)
(Not Included)
d

01 02 03 04 05 06 07
Step 6 Manage the Wires and Store the Allen Keys on Wire Clip
If the monitor is lower, remove the nut [h] and turn the bolt counter-clockwise with
supplied Allen key [o] to raise the monitor. Install the nut [h] after the adjustment.
Slightly Adjust the Height of each Monitor
h
Use the Allen key [o] to slightly
adjust the height of each monitor
and re-tighten the nut [h] after
finishing height adjustment.
Individual monitor height adjust-
ment helps monitors to be
perfectly aligned.
②
①ｏ
Small Allen Key
Remove the nut [h]
Warning:
To avoid tipping, please be
careful not to extend the arms
too far forward or backward.
When you adjust the angle of
the arms, please make sure
two arms are balanced to
avoid instability of the center
of gravity of the base.