Huawei UPS5000-H Series User manual

UPS5000-H-(400 kVA-800 kVA) Quick Guide (100 kVA Power Modules)
01 Installing Cabinets and Cables
Model Weight Dimensions (H x W x D)
UPS5000-H-400K-NT
< 800 kg 2000 mm x 800 mm x 1000 mmUPS5000-H-500K-NT
UPS5000-H-600K-NT
UPS5000-H-800K-NT < 1300 kg 2000 mm x 1600 mm x 1000 mm
Unpacking
Securing the Cabinet
A: mounting holes
on the channel steel
B: mounting holes
on the floor
unit: mm
Surge
protection
boxes
Control
module
Bypass
module
Power
modules
Battery input
Mains input Bypass
input UPS output
PE
Signal
cable route
(Perform this step only when the
mains input and bypass input use
different power sources.) Remove the
copper bars between the mains and
bypass input wiring terminals.
PE
Nut
Wiring
terminal
Spring
washer
Bolt
Flat
washer
Monitoring
Interface Card
Ambient
T/H Sensor
Dry Contact
Card
NC connection
NO connection
Issue: 03
Part Number: 31500FTV
Date: 2021-08-03
Item 400 kVA 500 kVA 600 kVA 800 kVA Remarks
Mains input
Mains input current (A)
743
929
1115
1486
Connection method:
Crimped DT terminal
Bolt Specifications:
L1/L2/L3/U/V/W/+/
-:
M16 x 55 mm
(120
N·m)
PE: M12 x 30 mm
(47
N·m
)
Equipotential ground
point: M6 x 12 mm (4.5
N·m
)
NOTE:
The currents listed in
the table are measured
at a rated voltage of
380 V.
Recommended cross
-sectional
area (mm
2)
L1/L2/L3/N
2 x (4 x 240)
3 x (4 x 185)
4 x (4 x 185)
4 x (4 x 240)
PE
240
Bypass input
Bypass input current (A)
608
760
912
1215
Recommended cross
-sectional
area (mm
2)
L1/L2/L3/N
2 x (4 x 240)
3 x (4 x 185)
4 x (4 x 185)
4 x (4 x 240)
PE
240
Output
Output current (A)
608
760
912
1215
Recommended cross
-sectional
area (mm
2)
U/V/W/N
2 x (4 x 240)
3 x (4 x 185)
4 x (4 x 185)
4 x (4 x 240)
PE
240
Battery input
(lead
-
acid battery)
Nominal battery discharge current (A)
887
1108
1330
1773
Maximum battery discharge current (A)
1062
1327
1593
2123
Recommended cross
-sectional
area (mm
2)
+/
-
2 x
(2 x 240)
3 x
(2 x 185)
4 x (2 x 185)
4 x (2 x 240)
PE
240
Battery input
(SmartLi
)
Nominal battery discharge current (A)
831
1039
1247
1662
Maximum battery discharge current (A)
1043
1304
1564
2086
Recommended cross
-sectional area (mm2)
For details, see the IEC
-60364-5-52 specifications and
SmartLi
User Manual.
Equipotential
ground point
Recommended cross
-sectional area (mm2)
16
1. Before installation, read the user manual carefully to get familiar with product information and safety precautions.
2. Use insulated tools when installing the equipment.
3. Only engineers certified by Huawei or its agent are allowed to install, commission, and maintain the UPS. Otherwise, personal injury or equipment damage
may occur, and the resulting UPS faults are beyond the warranty scope of Huawei.
4. This document describes the installation procedure for a single UPS. For details about how to install a parallel system, contact Huawei technical support.
•Cables of the same group,
for example, mains input
cables, must be routed
through the same cable hole.
•Different power sources are
used as an example.
•The number and color of
signal cables in the figure are
for reference only.
Ground bar
in the
equipment
room
1
Installing Cabinets and Cables（400–600 kVA）
Space planning
Installing Cables

01 02 全局信息
2
Installing Cabinets and Cables（800 kVA）
Space Planning Installing Cables
UPS5000-H-(400 kVA-800 kVA) Quick Guide (100 kVA Power Modules)
Unpacking
Securing the Cabinet
unit: mm
A: mounting holes on the channel steel
B: mounting holes on the floor
M12 bolt
Spring washer
Flat washer
Expansion sleeve
Expansion nut
Concrete floor
1. Check that there is no foreign matter in the cabinets.
2. (Remove the paper protective film from the sealing putty.) After routing cables and
verifying cable connections, seal the gap between cables and the cabinet using sealing putty.
3. After verifying the installation, reinstall all the covers.
4. Do not remove the dustproof cover before power-on to prevent dust from entering the UPS.
(Perform this step only when the mains input and bypass input use different power
sources.) Remove the copper bars between the mains and bypass input wiring terminals.
•Cables of the same group, for example, mains input
cables, must be routed through the same cable hole.
•Different power sources are used as an example.
•The number and color of signal cables in the figure
are for reference only.
Battery
input
Power
modules
Signal cable route
Surge protection
boxes
Bypass modules
Intelligent
detection
board
Control module
Ambient
T/H Sensor
Monitoring
Interface Card
Dry Contact
Card
NO connection NC connection
Dustproof
cover
Paper
protective
film
Sealing putty
Mains input
Bypass input
UPS output
02 Verifying the Installation
Equipotential
ground point

03 Power-On Commissioning
Powering On the UPS
3.1
Turn on the upstream bypass and mains input switches.
After the UPS is powered on, initialization begins. The monitoring display unit (MDU)
displays the Huawei logo and an initialization progress bar.
1. Before powering on the UPS5000, ensure that the check items in the UPS5000 Startup
Service Report and the post-installation check items are verified.
2. Measure the voltage and frequency of the UPS upstream input switch. The line voltage
range is 138–485 V AC, and the frequency range is 40–70 Hz.
Initial Startup
3.2
•If the UPS is powered on for the first time, you need to obtain the startup password from the
•Service Expert app. Skip this step if the UPS is not powered on for the first time.
•• The Service Expert app can be downloaded from Google Play Store and can run on Android.
1. Obtain the startup password.
2. Set the language, time, date, network parameters, and system parameters on the Settings
Wizard screen.
Starting the Inverter
3.3
3. After you perform the settings, the Bypass mode and No battery alarms are reported by the
MDU and do not need to be cleared. If there is any other alarm, you need to rectify the fault.
4. If the system has connected to the remote EPO switch, you need to choose Monitoring > UPS
System > Running Parameter > System Settings on the WebUI and set EPO detection to
Enable.
5. View the system running status diagram on the MDU to check that the UPS is working in
bypass mode.
Powering On Loads
3.4
04 Shutting Down the UPS
UPS5000-H-(400 kVA-800 kVA) Quick Guide (100 kVA Power Modules)
Set all battery parameters according to the actual situation: Assume that the battery
specifications are 150 Ah/12 V, 40 batteries are connected in series, and two battery strings
are connected to the UPS in parallel. Set Single battery voltage(V) to 12, Single battery
capacity(Ah) to 150, Battery in a battery string to 40, and Number of battery strings to 2.
Download and install the Service Expert app.
After login, tap Power-on password
activation on the screen. A message is
displayed, indicating whether to start the UPS.
Tap OK.
Insert the WiFi module into the USB port on
the MDU. Enable the mobile phone WLAN,
search for the UPS_WIFI signal, and connect to
the WiFi signal. The password is Changeme.
Set the Site and Device Type as required, and
connect the device. Set IP to 192.168.0.10, Port
to 443, Username to admin, Password to
Changeme, and click Login.
Enter Bar code and Verification code
obtained from the LCD on the Offline
Activation screen. Tap Generate PWD to
generate a startup password.
Set Site and Device Type as required,
and tap Offline Activation.
Enter the generated password in the
password text box on the LCD to start
the UPS.
Use the app to
start the UPS
online?
Yes
No, start
the UPS
offline
On the app home screen, tap StartUp to access the Set Startup screen.
System User LCD Preset
Password
WebUI Preset
Password
admin (system administrator)
000001 Changeme
operator (common user) 000001 Changeme
1. On the main menu, choose Common Functions and tap Inv. ON.
2. In the displayed login window, enter the user name and password, and tap .
3. In the displayed dialog box, tap Yes to start the inverter.
To ensure system security,
change the LCD and
WebUI passwords after
the first login.
1. After the inverter starts, the UPS works in normal mode. The Bypass mode alarm disappears
from the MDU.
2. After confirming that the battery strings are properly connected, turn on the battery string
input circuit breaker. If there are multiple battery strings, turn on the circuit breaker for each
battery string and then turn on the general circuit breaker between battery strings and the
UPS. The No battery alarm disappears from the MDU.
3. Turn on the UPS downstream output switch to supply power to the loads.
After you shut down the inverter, the UPS transfers to bypass mode if the bypass is normal;
the UPS supplies no power if the bypass is abnormal. Before shutting down the UPS, ensure
that all loads have been shut down.
Powering Off a Single UPS
4.2
Shutting Down the Inverter to Transfer the UPS to Bypass Mode
4.1
(Optional) Setting Parameters for the BCB Box
3.5
1. On the main menu of the LCD, choose Common Functions and tap Inv. OFF.
2. In the displayed login window, enter the user name and password, and tap .
3. In the displayed dialog box, tap Yes to shut down the inverter.
If a BCB box is configured, set MUE05A connection to Enable in System Info > Settings > Dry
Contacts Set, and then set BCB connection [OL] and Battery breaker [STA] to Enable.
Turn off the downstream output switch.
Turn off the upstream mains and bypass input switches.
Turn off the battery string circuit breaker of each power unit. If there are multiple
battery strings, turn off the general circuit breaker between battery strings
and the UPS and then turn off the circuit breaker for each battery string.
Scan here for more documents:
You can also log in to Huawei technical support website:
https://support.huawei.com/enterprise
https://support.huawei.com
Support
Support-E WeChat
Copyright © Huawei Technologies Co., Ltd. 2021. All rights reserved.
3