Huawei SmartLogger2000 series User manual

HUAWEI TECHNOLOGIES CO., LTD.
SmartLogger2000
Quick Guide
Issue: 04
Part number: 31508122
Date: 2018-06-13

1
1Overview
1. The information in this document is subject to change without notice. Every effort has been made
in the preparation of this document to ensure accuracy of the contents. However, all statements,
information, and recommendations in this document do not constitute a warranty of any kind,
express or implied.
2. Before installing the device, carefully read the SmartLogger2000 User Manual to get familiar with
the product information and precautions. SmartLogger is short for SmartLogger2000 in the
following text.
3. Install and use the device according to this document and the user manual. Otherwise, the device
may be damaged. Use insulated tools when installing the device.
4. When the SmartLogger is applied in a non-Huawei smart array controller (smart array controller
for short), install it in the third-party cabinet. This section describes the installation and cable
connection operations using the SmartLogger in non-Huawei smart array controller scenario as
an example.
Copyright © Huawei Technologies Co., Ltd. 2018. All rights reserved.
Model Description
1.1
NOTICE
Model
Description
Model
Description
SmartLogger2000
-10
10: with a built
-
in 500 V
AC PLC central
coordinator (CCO)
SmartLogger2000
-10-C 10-C: with a built-in
800 V AC PLC
central coordinator
(CCO)
11-C: with no built-
in
PLC CCO
SmartLogger2000
-10-B 10-B: with a built-in
500 V AC PLC
central coordinator
(CCO)
11-B: with no PLC
CCO
S
martLogger2000-11-C
SmartLogger2000
-11-B
N/A
N/A
The SmartLogger with a built-in PLC CCO can work with the SUN2000 integrated with the PLC
station (STA) to implement PLC networking.
If the SmartLogger with no built-in PLC CCO needs to work with the SUN2000 integrated with the
PLC STA to implement PLC networking, an external PLC CCO needs to be connected.
The Bluetooth module embedded in the SmartLogger2000-10 supports only the Android app. The
Bluetooth modules embedded in other models of SmartLoggers support both the Android app
and the iOS app.
This document uses the SmartLogger2000-10-C as an example to describe typical scenarios and
cable connections.
NOTE

2
Port Description
1.2
SmartLogger2000-10-C/11-C
No.
Port (Silk Screen)
Function Description
1
RF1, RF2
Reserved
Reserved.
2
12V OUT
12 V DC output
Provides 12 V DC power supply with a maximum
current of 100 mA.
3
12V IN
12 V DC input
Connects to the power adapter.
4
USB
USB port
Connects a USB flash drive.
5
SFP1, SFP2
Ethernet optical port
Connects to an ATB or another cascaded
SmartLogger.
6
ETH1, ETH2
Ethernet electrical
port
Connects to an Ethernet LAN switch, router, POE or
PC device.
7
DO
Digital output (DO)
Relay output supports 12 V voltage and 0.5 A current.
8
COM1
–COM6
RS485
communications
Six RS485 ports that can be connected to devices
such as the SUN2000, box
-type transformer, power
meter, or EMI.
9
Default
Default key
Resets and restarts the Bluetooth module or resets
the SmartLogger IP address to the default IP address
(valid within 5 minutes). The default IP address is
192.168.0.10.
10
AC1, AC2
a
AC power cable
ports
SmartLogger2000
-10-C: Connects to three-
phase (A,
B, and C) inputs
, and is used for PLC with the
SUN2000 over AC power cables.
SmartLogger2000
-11-C: disabled
11
Shell
ground point
N/A
12
AI1
–AI7
Analog input
AI1 supports 0
–10 V input voltage (passiveb); AI2–
AI7
support 0
–20 mA and 4–
20 mA input current (passive).
13
PT1, PT2
Analog input

PT1 supports the connection to a three-wire or two-
wire PT100/PT1000 temperature sensor.

PT2 supports the connection to only a two-wire
PT100/PT1000 temperature sensor.
14
AO1
–AO4
Analog output (AO)
4
–20 mA and 0–20 mA output current
15
DI1
–DI8
Digital input (DI)
Connects to a dry contact input. GND1 and GND2 are
ground ports for DI signals.
Note a: When the
SmartLogger is applied in a non-smart array controller, connect the AC1 and AC2
ports to the SPD with the delivered cables. The residue voltage of the SPD should be less than 6 kV.
Note b: Passive means that the AI port can connect to a sensor that needs to be energized separately.

No. Port (Silk Screen) Function Description
1
RF1, RF2
Reserved
Reserved.
2
12V OUT
12 V DC output
Provides 12 V DC power supply with a maximum
current of 100 mA.
3
12V IN
12 V DC input
Connects to the power adapter.
4
USB
USB port
Connects a USB flash drive.
5
SFP1, SFP2
Ethernet optical port
Connects to an ATB or another cascaded
SmartLogger.
6
ETH1, ETH2
Ethernet electrical
port
Connects to an Ethernet LAN switch, router, POE or
PC device.
7
DO
Digital output (DO)
Relay output supports 12 V voltage and 0.5 A current.
8
COM1
–COM6
RS485
communications
Six RS485 ports that can be connected to devices
such as the SUN2000, box
-type transformer, power
meter, or EMI.
9
Default
Default key
Resets and restarts the Bluetooth module or resets
the SmartLogger IP address to the default IP address
(valid within 5 minutes). The default IP address is
192.168.0.10.
10
AC1, AC2
AC power cable
ports

SmartLogger2000-10/10-
B: Connects to the A/B/C
three-phase input, and used for PLC with the
SUN2000 over AC power cables.

SmartLogger2000-11-B: disabled
11
Shell
ground point
N/A
12
AI1
–AI8
Analog input

SmartLogger2000-10: AI1–AI4: 4–20 mA and 0–
20
mA input current (passivea); AI5–AI8: 4–
20 mA and
0–20 mA input current (activeb)

SmartLogger2000-10-B/11-B: AI1: 0–10 V input
voltage (passive); AI2–AI4: 4–20 mA and 0–
20 mA
input current (passive); AI5–AI8: 4–20 mA and 0–
20 mA input current (active)
13
AO1
–AO6
Analog output (AO)
4
–20 mA and 0–20 mA output current
14
DI1
–DI8
Digital input (DI)
Connects to a dry contact input. GND1 and GND2
are ground ports for DI signals.
Note a: Passive means that the AI port can connect to a sensor that needs to be energized separately.
Note b: Active means that the AI port can connect to a sensor that need not be energized separately.
3
SmartLogger2000-10/10-B/11-B

4
2Typical Cable Connection Scenarios
Smart Array Controller Scenario
2.1
This document describes the application scenario where the SmartLogger is inside the smart
array controller SmartACU2000B-D-2PID/2PLC.
The tables under figures list only the components to be configured by the customer in the
corresponding scenario.
NOTE
NOTICE
1. Prepare the single-phase AC power cable for the smart array controller by yourself.
Recommended: a two-core outdoor armor copper cable with an operating voltage to the ground
greater than or equal to 300 V and a cross-sectional area of 4 mm2for each core wire
2. Prepare the power cable from the miniature circuit breaker (MCB) to the station-service power
source by yourself. Recommended: a two-core outdoor armor copper cable with an operating
voltage to the ground greater than or equal to 300 V and a cross-sectional area of 4 mm2for each
core wire
3. Prepare the three-phase AC power cable for the smart array controller by yourself. Recommended:
a four-core (L1, L2, L3, and functional earthing) outdoor armor copper cable with a cross-sectional
area of 10 mm2for each core wire. When the rated AC voltage on the low-voltage side of the box-
type transformer is less than or equal to 500 V, the operating voltage between the three-phase AC
power cable and the ground should be greater than or equal to 600 V. When the rated AC voltage
on the low-voltage side of the box-type transformer is greater than 500 V and less than or equal to
800 V, the operating voltage between the three-phase AC power cable and the ground should be
greater than or equal to 1000 V.
4. Prepare the power cable from the busbar to the Three-phase power switch by yourself.
Recommended: a four-core (L1, L2, L3, and functional earthing) outdoor armor copper cable with a
cross-sectional area of 10 mm2for each core wire. When the rated AC voltage on the low-voltage
side of the box-type transformer is less than or equal to 500 V, the operating voltage to the ground
should be greater than or equal to 600 V. When the rated AC voltage on the low-voltage side of
the box-type transformer is greater than 500 V and less than or equal to 800 V, the operating
voltage to the ground should be greater than or equal to 1000 V.

5
Optical Fiber

6
Location Component Recommended Model or
Specifications Component Source Quantity
Smart array
controller
LAN switch (optional) UT-H605 or ES1000 Can be purchased
from Huawei 1
Fitting bag
for optical
ring
switching
Low-
speed
optical
module
FTLF1323P1BTR-HW Can be
purchased
from Huawei
2
Optical
jumper
PLCLC5S-ST3P302-HW, LC-
LC-S2-L2,
3ECA1031LCLC002-01-F, or
LP-LP-2S-P-SM-002
8
Box-type
transformer
MCB Rated current: 32 A, number of
poles: 2 Prepared by the customer 1
Three-
phase
power
switch
Knife
fuse
switch
(solution
1)
When the rated AC voltage
on the low-voltage side of
the box-type transformer is
less than or equal to 500 V,
the rated voltage should be
greater than or equal to 500
V. When the rated AC
voltage on the low-voltage
side of the box-type
transformer is greater than
500 V and less than or
equal to 800 V, the rated
voltage should be greater
than or equal to 800 V.
Rated current of the fuse:
32 A; rated current of the
knife fuse switch box ≥ 32 A;
number of poles: 3 (3 fuses
for each knife fuse switch
box)
Prepared by
the customer
Scenario with a
double-column
transformer: 1
Scenario with a
dual-split
transformer: 2
MCCB
(solution
2)
When the rated AC voltage
on the low-voltage side of
the box-type transformer is
less than or equal to 500 V,
the rated voltage should be
greater than or equal to 500
V. When the rated AC
voltage on the low-voltage
side of the box-type
transformer is greater than
500 V and less than or
equal to 800 V, the rated
voltage should be greater
than or equal to 800 V.
Let-through energy ≤ 1.26 x
106A2s
Rated current: 32 A;
number of poles: 3
Prepared by
the customer

7
4G LTE

8
Location Component Recommended Model or
Specifications Component Source Quantity
Smart array
controller
LAN switch (optional) UT-H605 or ES1000 Can be purchased
from Huawei 1
Fitting
bags for
the POE
module
and
customer-
premises
equipment
(CPE)
POE
module N/A Can be
purchased
from Huawei 1
Outside the
smart array
controller
and box-
type
transformer
CPE N/A Can be purchased
from Huawei 1
Box-type
transformer
MCB Rated current: 32 A, number of
poles: 2 Prepared by the customer 1
Three-
phase
power
switch
Knife
fuse
switch
(solution
1)
When the rated AC voltage
on the low-voltage side of
the box-type transformer is
less than or equal to 500 V,
the rated voltage should be
greater than or equal to 500
V. When the rated AC
voltage on the low-voltage
side of the box-type
transformer is greater than
500 V and less than or
equal to 800 V, the rated
voltage should be greater
than or equal to 800 V.
Rated current of the fuse:
32 A; rated current of the
knife fuse switch box ≥ 32 A;
number of poles: 3 (3 fuses
for each knife fuse switch
box)
Prepared by
the customer
Scenario with
a double-
column
transformer: 1
Scenario with
a dual-split
transformer: 2
MCCB
(solution
2)
When the rated AC voltage
on the low-voltage side of
the box-type transformer is
less than or equal to 500 V,
the rated voltage should be
greater than or equal to 500
V. When the rated AC
voltage on the low-voltage
side of the box-type
transformer is greater than
500 V and less than or
equal to 800 V, the rated
voltage should be greater
than or equal to 800 V.
Let-through energy ≤ 1.26 x
106A2s
Rated current: 32 A; number
of poles: 3
Prepared by
the customer

Non-Smart Array Controller Scenario
2.2
NOTICE
Optical Fiber
9
1. If the SmartLogger communicates with a SUN2000 over an AC power cable, an MCB and a knife
switch need to be installed to prevent device damage in the case of short circuits.
2. If the SmartLogger communicates with the SUN2000 over an AC power cable, prepare the cable
from the knife fuse switch to the MCB and the cable from the busbar to the knife fuse switch by
yourself. Recommended: a three-core outdoor armor cable with a cross-sectional area of 10 mm2
for each core wire. When the rated AC voltage on the low-voltage side of the box-type transformer
is less than or equal to 500 V, the operating voltage between the AC power cable and the ground
should be greater than or equal to 600 V. When the rated AC voltage on the low-voltage side of
the box-type transformer is greater than 500 V and less than or equal to 800 V, the operating
voltage between the AC power cable and the ground should be greater than or equal to 1000 V.
3. The SmartLogger can connect to the SUN2000 through an RS485 communications cable or AC
power cable. If RS485 is used, there is no need to connect an AC power cable between the
SmartLogger and the MCB in the scenario without a smart array controller.
4. The power cable delivered with the SmartLogger is 1 meter long, the power adapter cable is 1.5
meters long, the network cable is 2.2 meters long, and the AC power cable is 1.5 meters long.
Reserve the installation positions for components based on the cable lengths.