Huawei HG531s V1 User manual

1
HG531s V1 300Mbps Wireless ADSL2+ Router
Quick Start
1 Connecting Cables
If you have subscribed to digital subscriber line (DSL) broadband, you can connect
the HG531s V1 to a telephone port for Internet access.
Follow the steps in the following figure to connect devices properly.
When configuring the HG531s V1 for the first time, use an Ethernet cable to
connect the HG531s V1 to a computer.
1 Telephone wall jack 2 Splitter 3 Telephone
4 Power adapter 5 Desktop computer 6 Set-top Box
7 Laptop computer 8 Smart Phone 9 Pad
a LINE port b MODEM port c PHONE port
MODEM
PHONE
LINE
1
23
4
5
6
7
8
9
a
b
c

2
2 Powering On
To power on the HG531s V1, press its power button.
After the HG531s V1 is powered on, the HG531s V1 indicator turns on. The following
table lists how the indicators behave when the HG531s V1 is operating correctly. If
the indicators do not behave as expected, ensure that everything is plugged in
correctly.
Indicator Expected State Description
Power Steady green The HG531s V1 is powered on.
ADSL
Blinking green A DSL connection is being activated.
Steady green A digital subscriber line (DSL) connection has been
set up and activated.
Internet
Blinking green The HG531s V1 is connected to the Internet in
router mode, and data is being transmitted.
Steady green The HG531s V1 is connected to the Internet in
router mode, but no data is being transmitted.
Off
The HG531s V1 is in router mode, but not
connected to the Internet.
The HG531s V1 is in bridge mode.
WLAN
Blinking green The HG531s V1 has WLAN enabled, and data is
being transmitted.
Steady green The HG531s V1 has WLAN enabled, but is not
transmitting data.
WPS
Blinking green
The HG531s V1 is attempting to connect to a
wireless client over the WLAN using the WPS
function.
The WPS indicator blinks for 120 seconds or less.
Steady green
The HG531s V1 is connected to a wireless client,
such as a computer with a wireless network
adapter, over the WLAN using the Wi-Fi Protected
Setup (WPS) function.
The WPS indicator is steady on for 300 seconds.

3
3 Setting Dial-Up Connection Parameters
Configuring a Dial-Up Connection to Access the Internet
The HG531s V1 works in bridge mode by default. You need to install and configure a
dial-up connection on your computer, and perform it each startup.
Before setting dial-up connection parameters, verify that the HG531s V1 is correctly
connected to your computer and you have the dial-up connection account name and
password provided by your Internet service provider (ISP). This section
demonstrates how to set up a Point-to-Point Protocol over Ethernet (PPPoE)
connection on Windows.
On Windows 7
1. Choose Start > Control Panel > Network and Internet > Network and
Sharing Center.
2. Under Change your networking settings, click Set up a new connection or
network.
3. In the Set Up a Connection or Network window, select Connect to the
Internet and click Next.
4. Click Broadband (PPPoE).
5. In User name and Password, enter the dial-up connection account name and
password provided by your ISP. In Connection name, name the dial-up
connection. Select or deselect Allow other people to use this connection.
Then click Connect.
LAN1 ～
LAN4
Blinking green The LAN port is connected to an Ethernet device
with a network cable, and data is being transmitted.
Steady green
The LAN port is connected to an Ethernet device
(such as a computer) with a network cable, but no
data is being transmitted.
USB
Blinking green The HG531s V1 is connected to a USB device, and
data is being transmitted.
Steady green The HG531s V1 is connected to a USB device, but
no data is being transmitted.
Indicator Expected State Description

4
6. Return to the Network and Sharing Center page. Click Change adapter
settings. Right-click the icon for the dial-up connection you just set up and
choose Create Shortcut from the shortcut menu. In the displayed dialog box,
click Yes.
On Windows XP
1. Choose Start > Control Panel > Network and Internet Connections >
Network Connections.
2. Under Network Tasks, click Create a New Connection.
3. In the Network Connection Wizard dialog box, click Next.
4. Select Connect to the Internet and click Next.
5. Select Set up my connection manually and click Next.
6. Select Connect using a broadband connection that requires a user name
and password and click Next.
7. In ISP Name, name the dial-up connection. Click Next.
8. Select Anyone's use or My use only and click Next.
9. Enter the dial-up connection account name and password provided by your
ISP and click Next.
10. Select Add a shortcut to this connection to my desktop and click Finish.
After you successfully set up a PPPoE connection, a dial-up connection icon is
displayed on your computer desktop.
To connect to the Internet, double-click the dial-up connection icon. In the displayed
dialog box, click Connect.
Configuring a Wireless Account
Before you log in to the HG531s V1 web management page, ensure that the
computer used for the login is connected to the HG531s V1 and has been configured
to automatically obtain an IP address or assigned with a static IP address.
The HG531s V1 provides an intuitive web management page where you can view or
set the HG531s V1 parameters. After you log in to the web management page, you
will see a configuration wizard page used to configure the wireless account.
The default SSID and WLAN Key printed on the HG531s V1's rear panel
are unique and secure. If you do not want to change them, click Next.
For security reasons or to make the password easy to remember, you can change
the wireless network name and password as follows:
1. Open a browser. In the address box, enter 192.168.1.1. Press Enter.

5
2. Enter the login user name (user by default) and password (@User1234 by
default). Click Login.
3. On the Quick Configure Router: Wireless Network page, enter your desired
WLAN name and password in WLAN SSID and Key, and click Next.
4 Wireless Connection Setup
The wireless configuration software provided by Windows is used as an example to
describe how to set up a wireless connection.
Before setting wireless connection, find the SSID and WLAN Key printed on the label
on the HG531s V1's rear panel.
On Windows 7
1. Click in the lower right corner of your desktop.
2. From the wireless network list, select the WLAN provided by the HG531s V1.
Click Connect.
3. In the displayed dialog box, enter the WLAN password and click OK.
4. In the wireless network list, check the WLAN connection status. If the status is
Connected, the computer is wirelessly connected to the HG531s V1.
On Windows XP
1. Click in the lower right corner of your desktop.
2. From the wireless network list, select the WLAN provided by the HG531s V1.
Click Connect.
3. In the displayed dialog box, enter the WLAN password and click Connect.
4. In the wireless network list, check the WLAN connection status. If the status is
Connected, the computer is wirelessly connected to the HG531s V1.

6
5 Security Maintenance Guide
Changing the Web Management Page User Name and
Password
The correct user name and password are required to log in to the web management
page. Regular changes to the web management page user name and password can
effectively prevent unauthorized users from logging in and modifying important
parameters.
1. Log in to the web management page.
2. In the navigation tree, choose Maintenance > Account.
3. In New user name, enter your desired user name.
4. In Current password, enter the currently used password.
5. In New password, enter the new password you specified. In Confirm
password enter the new password again.
6. Click Submit.
When modify password successfully, this page will jump to the login
page, enter the new user name and password to log in.
If you forget the password , you can press and hold the Reset button for 6
seconds or more, then the user name and password of the Web
management page will back to factory value. This operation will make your
own configuration data lost, please perform this operation with caution.
Changing Your WLAN Name and Password
WLAN access requires the WLAN name and password. To improve your WLAN
security, regularly change your WLAN name and password.
1. Log in to the web management page.
2. In the navigation tree, choose Basic > WLAN.
3. On the displayed page, enable your WLAN.
4. On the Wireless Settings area, enter your desired WLAN name and
password in SSID and WPA pre-shared key, and click Submit.
96722586_01

7
6 Safety information
This section contains important information about the operation of your device. It also contains
information about how to use the device safely. Read this information carefully before using your
device.
Electronic device
Do not use your device if using the device is prohibited. Do not use the device if doing so causes
danger or interference with other electronic devices.
Interference with medical equipment
> Follow rules and regulations set forth by hospitals and health care facilities. Do not use your
device where prohibited.
> Some wireless devices may affect the performance of hearing aids or pacemakers. Consult
your service provider for more information.
> Pacemaker manufacturers recommend that a minimum distance of 15 cm be maintained
between a device and a pacemaker to prevent potential interference with the pacemaker. If
using a pacemaker, hold the device on the side opposite the pacemaker and do not carry the
device in your front pocket.
Areas with flammables and explosives
> Do not use the device where flammables or explosives are stored (in a gas station, oil depot,
or chemical plant, for example). Using your device in these environments increases the risk of
explosion or fire. In addition, follow the instructions indicated in text or symbols.
> Do not store or transport the device in containers with flammable liquids, gases, or explosives.
Operating environment
> Avoid dusty, damp, or dirty environments. Avoid magnetic fields. Using the device in these
environments may result in circuit malfunctions.
> Before connecting and disconnecting cables, stop using the device and disconnect it from the
power supply. Ensure that your hands are dry during operation.
> Place the device on a stable surface.
> Keep the device away from electronic appliances that generate strong magnetic or electric
fields, such as a microwave oven or refrigerator.
> During thunderstorms, power off your device and remove all cables connected to it to protect
against lightning strikes.
> Do not use your device during thunderstorms to protect your device against any danger
caused by lightning.
> Ideal operating temperatures are 0 °C to 40 °C. Extreme heat or cold may damage your
device or accessories.
> Keep the device and accessories in a well-ventilated and cool area away from direct sunlight.
Do not enclose or cover your device with towels or other objects. Do not place the device in a
container with poor heat dissipation, such as a box or bag.
> To protect your device or accessories from fire or electrical shock hazards, avoid rain and
moisture.

8
> Keep the device away from sources of heat and fire, such as a heater, microwave oven,
stove, water heater, radiator, or candle.
> Do not place any object, such as a candle or a water container, on the device. If any foreign
object or liquid enters the device, immediately stop using it, power it off, and remove all cables
connected to it. Then, contact an authorized service center.
> Observe local laws and regulations, and respect the privacy and legal rights of others.
> Do not block device openings. Reserve a minimum of 10 cm around the device to dissipate
heat.
> Stop using your device or applications for a while if the device is overheated. If skin is
exposed to an overheated device for an extended period, low temperature burn symptoms,
such as red spots and darker pigmentation, may occur.
> Do not touch the device's antenna. Otherwise, communication quality may be reduced.
> Do not allow children or pets to bite or suck the device or accessories. Doing so may result in
damage or explosion.
> The device should be installed and operated with a minimum distance of 20 cm between the
radiator and your body.
> Keep the device in a place with good reception. The distance between the device and other
metal materials (such as metal brackets or metal doors and windows) should be greater than
25 cm and the distance between the device should be greater than 30 cm.
> If you connect a USB device to the HG531s V1, verify that the input voltage and current of the
USB device does not exceed 5V/0.65A. Otherwise, the HG531s V1 may malfunction.
Child's safety
> Comply with all precautions with regard to child's safety. Letting children play with the device
or its accessories may be dangerous. The device includes detachable parts that may present
a choking hazard. Keep away from children.
Accessories
> Using an unapproved or incompatible power adapter, charger or battery may cause fire,
explosion or other hazards.
> Choose only accessories approved for use with this model by the device manufacturer. The
use of any other types of accessories may void the warranty, may violate local regulations
and laws, and may be dangerous. Please contact your retailer for information about the
availability of approved accessories in your area.
Power adapter safety
> The power plug is intended to serve as a disconnect device.
> For pluggable devices, the socket-outlet shall be installed near the devices and shall be easily
accessible.
> Unplug the power adapter from electrical outlets and the device when not in use.
> Do not drop or cause an impact to the power adapter. If it is damaged, take it to an authorized
service center for inspection.
> If the power cable is damaged (for example, the cord is exposed or broken), or the plug
loosens, stop using it at once. Continued use may lead to electric shocks, short circuits, or
fire.

9
> Do not touch the power cord with wet hands or pull the power cord to disconnect the power
adapter.
> Do not touch the device or the power adapter with wet hands. Doing so may lead to short
circuits, malfunctions, or electric shocks.
> If your power adapter has been exposed to water, other liquids, or excessive moisture, take it
to an authorized service center for inspection.
> Ensure that the power adapter meets the requirements of Clause 2.5 in IEC60950-1/
EN60950-1 and has been tested and approved according to national or local standards.
Cleaning and maintenance
> During storage, transportation, and operation of the device, keep it dry and protect it from
collision.
> Keep the device and accessories dry. Do not attempt to dry it with an external heat source,
such as a microwave oven or hair dryer.
> Do not expose your device or accessories to extreme heat or cold. These environments may
interfere with proper function and may lead to fire or explosion.
> Avoid collision, which may lead to device malfunctions, overheating, fire, or explosion.
> If the device is not going to be used for an extended period of time, power it off, and remove all
cables connected to it.
> If anything unusual occurs (for example, if the device emits smoke or any unusual sound or
smell), immediately stop using it, power it off, remove all cables connected to it, and contact
an authorized service center.
> Do not trample, pull, or excessively bend any cable. Doing so may damage the cable, causing
the device to malfunction.
> Before you clean or maintain the device, stop using it, stop all applications, and disconnect all
cables connected to it.
> Do not use any chemical detergent, powder, or other chemical agents (such as alcohol and
benzene) to clean the device or accessories. These substances may cause damage to parts
or present a fire hazard. Use a clean, soft, and dry cloth to clean the device and accessories.
> Do not place magnetic stripe cards, such as credit cards and phone cards, near the device for
extended periods of time. Otherwise the magnetic stripe cards may be damaged.
> Do not dismantle or remanufacture the device and its accessories. This voids the warranty
and releases the manufacturer from liability for damage. In case of damage, contact an
authorized service center for assistance or repair.
Disposal and recycling information
This symbol (with or without a solid bar) on the device, batteries (if included), and/or
the packaging, indicates that the device and its electrical accessories (for example, a headset,
adapter, or cable) and batteries should not be disposed of as household garbage. These items
should not be disposed of as unsorted municipal waste and should be taken to a certified collection
point for recycling or proper disposal.

10
For more detailed information about device or battery recycling, contact your local city office,
household waste disposal service, or retail store.
Disposal of the device and batteries (if included) is subject to WEEE Directive Recast (Directive
2012/19/EU) and Battery Directive (Directive 2006/66/EC). The purpose of separating WEEE and
batteries from other waste is to minimize the potential environmental impacts and human health
risk of any hazardous substances that may be present.
Reduction of hazardous substances
This device is compliant with the REACH Regulation [Regulation (EC) No 1907/2006] and RoHS
Directive Recast (Directive 2011/65/EU). Batteries (if included) are compliant with the Battery
Directive (Directive 2006/66/EC). For up-to-date information about REACH and RoHS compliance,
please visit the web site www.huaweidevice.com/certification.
EU regulatory conformance
Statement
Hereby, Huawei Technologies Co., Ltd. declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
For the declaration of conformity, visit the web site www.huaweidevice.com/certification.
The following marking is included in the product:
This device may be operated in all member states of the EU.
Observe national and local regulations where the device is used.
This device may be restricted for use, depending on the local network.
Restrictions in the 2.4 GHz band:
Norway: This subsection does not apply for the geographical area within a radius of 20 km from the
centre of Ny-Ålesund.
FCC Regulatory Compliance
FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
0979

11
--Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
--Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Caution: Any changes or modifications to this device not expressly approved by Huawei
Technologies Co., Ltd. for compliance could void the user's authority to operate the equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. This equipment should be installed and operated with a minimum distance
of 20 centimeters between the radiator and your body.
FCC-PART 68
> This equipment complies with Part 68 of the FCC rules and the requirements adopted by the
ACTA. On the back of this equipment is a label that contains, among other information, a
product identifier in the format
US: HAUDL01BHG531V1
> It uses the following USOC jacks: RJ45, RJ11.
> The REN is used to determine the number of devices that may be connected to a telephone
line. Excessive RENs on a telephone line may result in the devices not ringing in response to
an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To
be certain of the number of devices that may be connected to a line, as determined by the
total RENs, contact the local telephone company. For products approved after July 23, 2001,
the REN for this product is Customer Information 3 July 2003 part of the product identifier that
has the format US:HAUDL01BHG531V1. The digits represented by 01 are the REN without a
decimal point (e.g., 03 is a REN of 0.3)."
> A plug and jack used to connect this equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA.
> A compliant telephone cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. See installation instructions for
details. If this equipment, the 300Mbps Wireless ADSL2+ Router , causes harm to the
telephone network, the telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice isn’t practical, the telephone
company will notify the customer as soon as possible. Also, you will be advised of your right to
file a complaint with the FCC if you believe it is necessary.
> The telephone company may make changes in its facilities, equipment, operations or
procedures that could affect the operation of the equipment. If this happens the telephone
company will provide advance notice in order for you to make necessary modifications to
maintain uninterrupted service.
> If trouble is experienced with this equipment, 300Mbps Wireless ADSL2+ Router, for repair or
warranty information. please contact: Futurewei Technologies, Inc. Phone: [phone]
> If the equipment is causing harm to the telephone network, the telephone company may
request that you disconnect the equipment until the problem is resolved.
> If your home has specially wired alarm equipment connected to the telephone line, ensure the
installation of this device. does not disable your alarm equipment. If you have questions about
what will disable alarm equipment, consult your telephone company or qualified installer.
> Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.

12
Electrical Safety Advisory
Telephone companies report that electrical surges, typically lightning transients, are very
destructive to customer terminal equipment connected to AC power sources. This has been
identified as a major nationwide problem.
Therefore it is advised that this equipment be connected to AC power through the use of a surge
arrestor or similar protection device.
Warnings: This is a Class B product. In a domestic environment this product may cause radio
interference, in which case the user may be required to take adequate measures. Adequate
measures include increasing the physical distance between this product and other electrical
devices.
7 Obtaining More Information
Thanks for purchasing the HG531s V1 300Mbps Wireless ADSL2+ Router
(HG531s V1 for short).
This quick start guide will show you how to connect your HG531s V1 to a network and
access the Internet. The figures in this guide are for reference only. The appearance
and display features may vary slightly depending on the actual product version.
For more information, visit http://consumer.huawei.com/en/.
Please visit http://consumer.huawei.com/en/support/hotline for recently updated
hotline and email address in your country or region.
8 Legal Notice
Copyright © Huawei Technologies Co., Ltd. 2014. All
rights reserved.
THIS DOCUMENT IS FOR INFORMATION PURPOSE ONLY, AND DOES NOT
CONSTITUTE ANY KIND OF WARRANTIES.
Privacy Policy
To better understand how we protect your personal information, please see the
privacy policy at http://consumer.huawei.com/privacy-policy.