Hubbardton Forge 302620 Programming manual

MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM 42403
ASSEMBLY & INSTALLATION INSTRUCTIONS
Refraction Outdoor Sconces 302620 & 302623
B403
1 OF 6
302620
Instructions cover both
302620 and 302623.
Component quantities may vary.
302623

MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM 42403
ASSEMBLY & INSTALLATION INSTRUCTIONS
Refraction Outdoor Sconces 302620 & 302623
B403
Component Parts
A Fixture
B Front Tube
C Thumb Screw (4)
D Rubber Washer (6)
E Mounting Bracket
F Ground Screw
G Cupped Washer
H Caulking Lip
I #8 Screws (4)
J Glass (2)
K Anchor (4)
L Flat Head Screw (2)
M Set Screw (2)
N Socket (2)
O Bulb (2 - Included)
2 OF 6

MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM 42403
ASSEMBLY & INSTALLATION INSTRUCTIONS
Refraction Outdoor Sconces 302620 & 302623
B403
1. Carefully unpack the xture (A) from the carton.
2. Remove mounting bracket (E) from xture and set aside.
3. Remove lower set of thumb screws (C) and rubber washers (D). Loosen top set of thumb screws and rubber washers
but do not remove completely.
4. Slide front tube (B) upward and detach from xture (A). Set aside front tube (B) for later use (Figure 1).
See Figures 2 & 3 on next page for following instructions.
5. Using two machine screws (not provided) attach mounting bracket (E) to the electrical box.
Note: A new electric box comes with screws. When replacing a fixture, retain the existing screws for use with the new
fixture.
6. Using the green ground screw (F) and the cupped washer (G) in kit bag, secure a pigtail lead to the mounting
bracket (E).
To Attach to Wall (Figures 1 - 3)
CAUTION:FAILURE TO INSTALLTHIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONALINJURY OR DEATH AND
PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Please Note: After installation extra hardware and accessories are possible; our kits are used on multiple products.
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED
ON SECURELY, AND NO BARE WIRES ARE EXPOSED.
D
C
B
A
E
(Figure 1)
3 OF 6
7. Hold the xture (A) close to the mounting bracket (E) and
using suitable wire connectors (not provided), connect
xture wires to supply wire (white to white and black to
black). Connect all ground wires (bare copper or green to
bare copper or green).
8. Apply a generous bead of a suitable caulking material
(not provided) to caulking lip (H) on the xture. Caulk
should be applied around the entire perimeter of the
backplate (Figure 3).
9. Carefully tuck all wires behind xture and inside the
mounting bracket (E). Place xture rmly onto bracket
and fasten with two #8 screws (I) and rubber washers (D)
on top.
Be sure Triangle plate is pointing upwards as seen in
Figure 2.
Note: Be sure no wires are pinched between wall and
fixture.
10. Install the two remaining #8 screws (I) in bottom of
xture.

MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM 42403
ASSEMBLY & INSTALLATION INSTRUCTIONS
Refraction Outdoor Sconces 302620 & 302623
B403
D
I
Triangle
Plate
A
MACHINE
SCREWS
GF
E
(Figure 2)
(Figure 3)
H
4 OF 6

MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM 42403
ASSEMBLY & INSTALLATION INSTRUCTIONS
Refraction Outdoor Sconces 302620 & 302623
B403
TEXTURED
SURFACE
M
L
K
J
B
(Figure 4)
To Prepare Glass for Installation (Figure 4 )
1. Unpack glass (J).
2. Place glass (J) on a clean surface. Press anchors (K) into
holes in glass from each side until anchor is ush with side
of glass.
3. Locate front tube assembly (B). Place glass into front tube
with textured surface oriented as shown in Figure 4.
Note: It may be necessary to loosen set screw (M) to allow
glass to pass into tube.
4. Align anchors (K) in glass with holes in front tube (B).
Thread flat head screws (L) into anchors evenly to secure
glass to tube.
5. Using hex wrench provided, snug set screw (M) against
glass. Be careful not to overtighen and break glass.
6. For 302623 - Repeat steps for second piece of glass.
7. Follow steps on next page to complete installation.
5 OF 6

MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM 42403
ASSEMBLY & INSTALLATION INSTRUCTIONS
Refraction Outdoor Sconces 302620 & 302623
B403
ALIGNMENT
STUD
SLOT
N
C
B
O
A
D
(Figure 5)
B
A
BACK VIEW
C
D
HOLE FOR
ALIGNMENT
STUD
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you
purchased this product. We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of
this xture.
To Complete Installation (Figure 5)
1. Install bulbs (O) (included) into sockets (N).
2. Orient front tube (B) assembly so that installed thumb
screws and washers are towards the top.
3. Front tube (B) assembly can only be installed one way.
The hole in front tube (B) will need to line up with the
alignment stud on the xture (A).
4. Tilt front tube (B), slip over bulbs (O) and slide thumb
screws (C) and rubber washers (D) down into slots on top
of xture (A).
Note: Be sure rubber washers (D) are on the backside of
the fixture as seen in Figure 5 - back view.
5. Align bottom holes in fixture with tube (B) and install
remaining thumb screws (C) and rubber washers (D) to
secure front tube assembly.
Note: Make sure all thumb screws are as tight as
possible.
6. Restore electricity at main breaker.
6 OF 6
Caution: Be careful not to hit bulbs with front tube.