Hubbardton Forge Shard Outdoor Sconce XL 302518 Programming manual

MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM 44708
ASSEMBLY & INSTALLATION INSTRUCTIONS
Shard Outdoor Sconce XL 302518
B423

MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM 44708
ASSEMBLY & INSTALLATION INSTRUCTIONS
Shard Outdoor Sconce XL 302518
B423
Component Parts
A. Fixture Assembly
B. Mounting Bracket
C. #8 Screws (4)
D. Rubber Washer (2)
E. Ground Screw
F. Cupped Washer
G. Caulking Lip
H. Plate Assembly
I. Plate Screws (2)
J. Glass
K. Set Screw (2)
2 OF 5

MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM 44708
ASSEMBLY & INSTALLATION INSTRUCTIONS
Shard Outdoor Sconce XL 302518
B423
1. Carefully unpack the xture (A) from the carton.
2. Plate assembly (H) is shipped installed. Remove plate by removing
the two plate screws (I) (Figure 1). Remove mounting bracket (B).
3. Using two machine screws (not provided) attach mounting bracket (B)
to the electrical box (Figure 2).
Note: A new electric box comes with screws. When replacing a fixture,
retain the existing screws for use with the new fixture.
4. Using the ground screw (E) and the cupped washer (F) found in kit
bag, secure a pigtail lead to the mounting bracket (B).
5. Hold the xture (A) close to the mounting bracket (B) and using suit-
able wire connectors (not provided), connect xture wires to supply
wire (white to white and black to black). Connect all ground wires
(bare copper or green to bare copper or green).
6. Apply a generous bead of a suitable caulking material (not provided)
to caulking lip (G) on the xture. Caulk should be applied around the
entire perimeter of the backplate (Figure 3).
7. Carefully tuck all wires behind xture and inside the mounting bracket
(B). Place xture rmly onto bracket and fasten with two #8 screws
(C) and rubber washers (D) on top.
Note: Be sure no wires are pinched between the wall and fixture.
8. Install the two #8 screws (C) in bottom of xture.
To Install Fixture (Figures 1, 2 & 3, following pages)
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH
AND PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance
with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Please Note: After installation extra hardware and accessories are possible; our kits are used on multiple products and options.
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON
SECURELY AND NO BARE WIRES ARE EXPOSED.
3 OF 5
H
I
A
(Figure 1)

MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM 44708
ASSEMBLY & INSTALLATION INSTRUCTIONS
Shard Outdoor Sconce XL 302518
B423
4 OF 5
MACHINE
SCREWS
D FE
C
B
C
(Figure 2)
A
G
(Figure 3)

MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM 44708
ASSEMBLY & INSTALLATION INSTRUCTIONS
Shard Outdoor Sconce XL 302518
B423
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you
purchased this product. We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of
this xture.
5 OF 5
To Complete Install (Figures 4 & 5)
1. Carefully slide glass (J) into plate assembly (H). The side
of the glass (J) with di󰀨erent colored pieces should be fac-
ing the set screws (K).
Note: It may be necessary to back out set screws (K)
before glass (J) can be dropped it. It is not necessary to
completely remove set screws (K).
2. Center glass (J) in plate assembly (H) and, using hex
wrench (provided), tighten both set screws (K) until snug
against glass (J). Be careful not to overtighten.
3. Hold plate assembly (H) with glass (J) installed up to xture
assembly (A). Install two plate screws (I) to secure plate
assembly (H).
Note: Set screws should be facing wall.
4. Restore electricity at main breaker.
J
K
H
(Figure 4)
(Figure 5)
H
I
J
A