Hubbardton Forge Elton 303050 User manual

HUBBARDTONFORGE.COM
-, -   
154 RT. 30 SOUTH • CASTLETON, VERMONT 05735
All designs and images ©1989-2013 Hubbardton Forge®. All rights reserved. 30801
Installation Instructions
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product.
We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this xture.
Please Note: This fixture is designed to be mounted on a standard wall
surface and may not be suitable for all applications. If installing in a non-
wood frame application, we recommend consulting a qualified builder
or electrician.
To Mount Fixture to Wall (Figures 1 & 2)
Component Parts
A Fixture Assembly
B Mounting Bracket
C Anchors (4)
D #10 Screws (4)
E #8 Screws (4)
F Ground Screw
G Cupped Washer
H Rubber Washers (2)
I Caulking Lip
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX
PRIOR TO INSTALLATION.
1. Carefully unpack the xture from the carton.
2. Using two machine screws (not provided), fasten the
mounting bracket (B) to the electrical box.
Note: A new electrical box comes with screws. When replacing a
xture, retain the existing screws for use with the new xture.
3. If mounting bracket (B) can’t be mounted to the electrical
box, follow steps 4 through 6 to attach mounting bracket to
the wall using anchors (C).
4. Center the mounting bracket (B) over the electrical box
being sure to hold it plumb and level. With a pencil, mark
the location of all mounting holes in the mounting bracket on
the wall behind.
5. Put the mounting bracket (B) down and drill 1/4" holes in the
locations marked on the wall. For holes using anchors (C),
place the tapered end of the anchors (C) into the holes and
gently tap them ush to the wall using a light weight hammer.
cupped washer (G) to the electrical box and connect
all ground wires (bare copper or green to bare copper or
green).
B320
Elton Outdoor Sconce 303050, 303053 & 303055 Page 1 of 3
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND
PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
(Figure 1)
(Continued)
(Figure 2)
I
G
C
F
B
H
D
A
E

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product.
We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this xture.
HUBBARDTONFORGE.COM
-, -   
154 RT. 30 SOUTH • CASTLETON, VERMONT 05735
All designs and images ©1989-2013 Hubbardton Forge®. All rights reserved. 30801
Installation Instructions
To Mount Fixture to Wall (Figures 1 & 2)
(Continued)
6. Thread the wires in the electrical box through the center
hole in the mounting bracket (B) while moving the bracket
into position. Using the #10 screws (D), screw the bracket
securely to the wall. Be careful not to over-tighten or strip
the anchors.
7. Hold the fixture assembly (A) close to the mounting bracket
and using suitable wire connectors (not provided), connect
fixture wires to supply wires (white to white and black to
black). Run a pigtail lead from the crossbar ground screw
(F) and cupped washer (G) to the electrical box and connect
all ground wires (bare copper or green to bare copper or
green).
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON
SECURELY, AND NO BARE WIRES ARE EXPOSED.
8. Apply a generous bead of a suitable caulking material to
caulking lip (I) on fixture. (Figure 2)
9. Carefully tuck all wires behind the fixture assembly (A) and
inside the mounting bracket and place the fixture firmly onto
bracket (B) and fasten with #8 screws (E) and rubber
washers (H) on top.
10. Install two remaining #8 screws (E) in bottom of fixture
attaching to mounting bracket (B).
To Install Glass (Figures 3 & 4)
Component Parts
A Fixture Assembly
J Glass Panel (4)
K Glass Clip (4)
L Glass Shelf (4)
M Bulb (not provided)
1. There are two sizes of glass (J) for this xture. The two taller
panels go in the front of the xture and the two shorter
panels go in the back of the xture. The at end of the glass
will go towards the top of the xture. Tapered end towards
bottom.
See Figure 3 for orientation.
2. Install bulb (M) into xture. (bulb not provided)
B320
Elton Outdoor Sconce 303050, 303053 & 303055 Page 2 of 3
(Figure 3)
(Continued)
FIXTURE FRONT
TALL GLASS PANELS
SHORT GLASS
PANELS
FIXTURE BACK

HUBBARDTONFORGE.COM
-, -   
154 RT. 30 SOUTH • CASTLETON, VERMONT 05735
All designs and images ©1989-2013 Hubbardton Forge®. All rights reserved. 30801
Installation Instructions
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product.
We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this xture.
To Install Glass (Figures 3 & 4)
(Continued)
3. Starting with one of the tall glass panels (J), twist the glass
and slide it up into the xture (A) past the bulb (M).
4. Push glass (J) up past the glass clip (K).
Note: For proper glass t, glass clips (K) may need to be adjusted.
5. Slide the glass (J) down until it sits on the glass shelf (L).
This will secure glass panel (J).
6. Repeat with other glass panels (J).
7. Restore electricity at main breaker.
B320
Elton Outdoor Sconce 303050, 303053 & 303055 Page 3 of 3
(Figure 4)
M
K
L
J
A