Hubbardton Forge Erlenmeyer Dark Sky Programming manual

43654
ASSEMBLY & INSTALLATION INSTRUCTIONS
Erlenmeyer Dark Sky Outdoor Sconce 307716
B415
1 OF 4

43654
ASSEMBLY & INSTALLATION INSTRUCTIONS
Erlenmeyer Dark Sky Outdoor Sconce 307716
B415
A Fixture
B Mounting Bracket
C Anchors (4)
D #10 Scews (4)
E Ground Screw
F Cupped Washer
G Caulking Lip
H #8 Screws (4)
I Rubber Washer (2)
J Bulb (LED Version Included)
K Metal Shade
L Thumb Screw (3)
Component Parts
2 OF 4

43654
ASSEMBLY & INSTALLATION INSTRUCTIONS
Erlenmeyer Dark Sky Outdoor Sconce 307716
B415
A
C
D
B
E FI H
To Install Fixture (Figures 1 & 2)
CAUTION:FAILURETOINSTALLTHISFIXTUREPROPERLYMAYRESULTINSERIOUSPERSONALINJURYORDEATHAND
PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Please Note: After installation extra hardware and accessories are possible; our kits are used on multiple products.
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
3 OF 4
1. Carefully unpack the xture (A) from the carton.
2. Take o󰀨 rubber band and remove mounting bracket (B) from
xture (A).
3. Place the mounting bracket (B) over the electrical box being
sure to hold it level. Line up holes in mounting bracket with
holes in electrical box. With a pencil, mark the location of all
mounting holes in the mounting bracket on the wall behind.
Set bracket aside.
4. Drill 1/4" holes in the locations marked on the wall. Place the
tapered end of the anchors (C) into the holes and gently tap
them ush to the wall using a light weight hammer.
5. Thread the wires in the electrical box through the hole in
the mounting bracket (B) while moving the bracket into
position. Using (2) #8 machine screws (not provided), attach
the crossbar securely to the junction box.
Note: A new electric box comes with screws. When
replacing an existing xture, retain screws for use with the
new xture
6. Using #10 screws (D), screw the bracket securely to the
wall. Be careful not to over-tighten or strip the anchors (C).
7. Attach a pigtail lead to the mounting bracket (B) using the
ground screw (E) and cupped washer (F) found in kit bag.
8. Hold xture (A) close to wall. Using suitable wire connectors
(not provided), connect xture wires to supply wires (white
to white and black to black). Connect all ground wires (bare
copper or green to bare copper or green).
9. Apply a generous bead of a suitable caulking material (not
provided) to caulking lip (G) on the xture (Figure 2).
10. Place xture (A) over mounting bracket (B). Secure with #8
screws (H) and rubber washer (I) on top and #8 screws (H)
bottom of xture. Be sure no wires are pinched between
xture and wall.
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED
ON SECURELY, AND NO BARE WIRE IS EXPOSED.
(Figure 1)
G
(Figure 2)

43654
ASSEMBLY & INSTALLATION INSTRUCTIONS
Erlenmeyer Dark Sky Outdoor Sconce 307716
B415
1. Locate and unpack metal shade (K)
2. Install Bulb (J) - LED Version Included, into socket.
3. Loosen three thumb screws (L). It is not necessary to
remove them from the xture (A).
4. Raise metal shade (K) until groove is aligned with
thumb screws (L). Top of metal shade (K) should be
inside Top Cap as shown in Figure 3.
5. Tighten thumb screws (L) evenly until snug against
metal shade (K).
6. Restore electricity at main breaker.
To Install Metal Shade (Figure 3)
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you
purchased this product. We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this
xture.
4 OF 4
(Figure 3)
K
L
J
A
TOP CAP
GROOVE