Hubbardton Forge 36-5605 User manual

Installation Instructions A191
For Outdoor Semi-Flush 36-5605 & 36-5605F Page 1 of 2
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735 21174
To Install Fixture (Figure 1)
Component Parts
A Crossbar
B Ground Screw
C Threaded Stud (2)
D Canopy
E Barrel Knobs (2)
F Glass Retaining Ring (2)
Caution: Be sure power is off at the main breaker box prior to installation
1. Carefully unpack the fixture from the carton.
2. Thread studs (C) through appropriate holes in cross bar (A) to match
hole centers in canopy (D). Move ground screw (B) to another
available threaded hole if necessary.
3. Using two machine screws (not provided) fasten cross bar (A) to the
electric box using outer oval holes to orient fixture to desired hanging
position. Note: A new electric box comes with screws. When replacing
an existing fixture, retain the screws for use with the new fixture.
5. Using suitable wire connectors (not provided) connect fixture wires to supply
wires (white to white or ribbed and black to black or smooth). Connect all
ground wires to green ground screw (B). Caution: Make sure wire connectors
are twisted on securely, and no bare wire is exposed.
6. Slide fixture canopy (D) over threaded studs and push firmly to ceiling, making
sure that no wires are pinched between fixture canopy and ceiling. Fasten with
barrel knobs (E). Be sure studs (C) are fully seated in the barrel knobs (E).
7. Remove glass retaining ring (F) and save for later use.
8. Refer to instructions below to install glass & bulb.
To Install Outer Glass (Figure 2)
Component Parts
G Screws (3)
H Socket
I Outer Glass (larger diameter glass)
J Spider Assembly
1. Unthread screws (G) that are shipped installed in threaded bosses on underside
of fixture next to socket (H). Loosen screws until there are only a couple
threads engaged with the threaded bosses.
(continued)
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
(Figure 1)
(
Fi
g
ure
2
)

Installation Instructions A191
For Outdoor Semi-Flush 36-5605 & 36-5605F Page 2 of 2
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735 21174
2. Slip outer glass (I) over spider assembly (J).
3. Raise spider assembly (J) with outer glass (I) installed and slip over socket (H) aligning holes in the top of the
spider assembly (J) keyed ring goes over screws (G).
4. Turn spider assembly (J) counter clockwise until it stops. Tighten three screws (G) until snug against the spider
assembly. Be careful not to over tighten.
To Install Inner Glass (Figure 3)
Component Parts
F Glass Retaining Ring (2)
K Inner Glass
1. Slip inner glass (K) over socket.
2. Thread the first retaining ring (F) onto socket until it is against top of the inner
glass (K).
3. Thread the second retaining ring (F) onto socket until it is snug against the first
retaining ring. Do not over tighten.
4. Install light bulb. “F” version bulb is included.
5. Restore electricity at main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
(
Fi
g
ure
3
)