Hubbardton Forge Double Ursa 302507 Programming manual

45136
ASSEMBLY & INSTALLATION INSTRUCTIONS
Double Ursa 302507
B427
1 OF 8
302643

45136
ASSEMBLY & INSTALLATION INSTRUCTIONS
Double Ursa 302507
B427
A. Fixture
B. Mounting Bracket
C. Lower Decorative Plate
D. Upper Decorative Plate
E. #8 Screws (4)
F. Ground Screw
G. Cupped Washer
H. Rubber Washer (2)
I. Caulking Lip
J. Upper Spacer Assembly
K. Lower Spacer Assembly
L. Thumbscrew
M. Adjustment screw
N. Glass (2)
O. Set screw
P. Bottom Bracket
Q. Bottom Rod
R. Upper Rod
S. #10 Screws (4)
T. Upper Decorative Plate Screws (2)
U. Lower Decorative Plate Screws (2)
Component Parts
2 OF 8

45136
ASSEMBLY & INSTALLATION INSTRUCTIONS
Double Ursa 302507
B427
To Install Fixture (Figures 1 & 2)
CAUTION:FAILURETOINSTALLTHISFIXTUREPROPERLYMAYRESULTINSERIOUSPERSONALINJURYORDEATHAND
PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Please Note: After installation extra hardware and accessories are possible; our kits are used on multiple products.
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
3 OF 8
1. Carefully unpack the xture (A) from the carton.
2. The xture is wrapped in plastic wrap. Remove plastic wrap and foam block.
3. Locate the mounting bracket (B), found in the kit bag.Thread the wires in the electrical box through the hole
in the mounting bracket (B) while moving the bracket into position. Using (2) #8 machine screws (not pro-
vided), attach the bracket securely to the junction box. Make sure bracket is level. (Figure 2)
Note: A new electric box comes with screws. When replacing an existing xture, retain screws for use with
the new xture
4. Attach a pigtail lead to the mounting bracket (B) using the ground screw (F) and cupped washer (G) found
in kit bag.
5. Orient xture (A) such that the glass shield is facing upward.
6. Hold xture (A) close to wall. Using suitable wire connectors (not provided), connect xture wires to supply
wires (white to white and black to black). Connect all ground wires (bare copper or green to bare copper or
green).
7. Apply a generous bead of a suitable caulking material (not provided) to caulking lip (I) on the xture (Figure
3).
8. Place xture (A) over mounting bracket (B). Secure with #8 screw (E) and rubber washers (H) on top and
#8 screws (E) in bottom of xture. Be sure no wires are pinched between xture and wall.
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY, AND NO BARE WIRE IS
EXPOSED.

45136
ASSEMBLY & INSTALLATION INSTRUCTIONS
Double Ursa 302507
B427
(Figure 1)
(Figure 2)
GLASS SHIELD
G
I
FE HA
4 OF 8
MACHINE
SCREWS
B

45136
ASSEMBLY & INSTALLATION INSTRUCTIONS
Double Ursa 302507
B427
1. Using diagram in Figure 4, place marks on the wall to locate the upper and lower spacer assemblies (J & K).
Note: Measurements are from the edge of the mounting can of the xture to the centerline of the spacer.
2. Remove thumbscrew (L) from upper spacer (J) and set aside for use later.
To Install Upper and Lower Spacers. (Figure 3)
Note: Upper spacer (J) has a round hole and
Lower spacer (K) has a square hole.
3. Hold appropriate spacer level on the wall and
using two #10 screws (S) fasten the spacer to
the wall. Repeat for the other spacer.
(Figure 3)
5 OF 8
J
L
A
NOT TO SCALE
NOT TO SCALE
S
S

45136
ASSEMBLY & INSTALLATION INSTRUCTIONS
Double Ursa 302507
B427
To Install Lower Glass/Decorative Assembly (Figure 4)
1. Carefully slide glass (N) into lower decorative as-
sembly (C) until it settles into bottom bracket (P).
It may be necessary to loosen the set screw (O) to
allow glass to drop into the bottom bracket (P).
Note: Be sure not to drop glass (N) into bottom
bracket as glass could chip from the force.
2. Using hex wrench (provided), tighten set screw (O)
in bottom bracket (P) until snug against glass (N).
Be sure not to overtighten.
3. Place lower decorative assembly (C) and glass (N)
up into xture assembly (A) while aligning bot-
tom rod (Q) with lower spacer assembly (K) install
screws (U).
4. If adjustment is needed to hold lower decorative
assembly parallel with wall, loosen adjustment
screw (M), move lower decorative assembly to
desired position and retighten screw.
Note: It is not necessary to completely remove
adjustment screw (M) from lower spacer assembly
(K).
6 OF 8
A
U
K
Q
P
N
C
M
(Figure 4)
O

45136
ASSEMBLY & INSTALLATION INSTRUCTIONS
Double Ursa 302507
B427
1. Remove screws (T) from side brackets on xture (A).
2. Carefully slide glass (N) into upper decorative assembly (D).
3. Locate upper rod (R). Insert round end through the decorative assembly (D) until U-shaped piece is aligned with
glass (N). Rotate glass holder 90 degrees so that the u shaped piece ts around the glass (N).
4. While holding the decorative assembly (D), glass (N) and upper rod (R) together, place on top of xture so that legs
on the upper decorative assembly (D) slide behind the xture and align with the side brackets. Make sure that the
square block on the top of the assembly (D) ts over the upper spacer assembly (J).
5. Slowly let the glass (N) slide down until it sets on the glass shield on the top of the xture (A).
Note: Be sure not to drop glass (N) onto glass shield. Both glass pieces could break.
6. Attach upper decorative assembly (D) to xture using 2 screws (T).
7. Adjust upper rod (R) to hold glass (N) vertical. Put thumb screw (L) through square block on the back of assembly
(D), thread into upper spacer assembly (J) and tighten against the upper rod (R).
8. Restore electricity at main breaker.
To Install Upper Glass/Decorative Assembly (Figure 5 & 6)
7 OF 8

45136
ASSEMBLY & INSTALLATION INSTRUCTIONS
Double Ursa 302507
B427
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you
purchased this product. We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this
xture.
8 OF 8
BRACKET
J
LN D
R
N
D
T
GLASS SHIELD
(Figure 6)
(Figure 5)
LEG
BLOCK