Huffy Table-Top Basketball Game User manual

107/03 P/N 211737A
© COPYRIGHT 2000 by HUFFY SPORTS
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-333 061
Internet Address: http://www.huffysports.com
REQUIRED TOOLS AND MATERIALS:
• Phillips Head Screwdriver
Table-Top Basketball Game
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Read and understand
operator's manual before
using this unit.
Failure to follow operating
instructions could result
in injury or damage to
property.
NOT SUITABLE FOR CHILDREN
UNDER THREE YEARS OF AGE
DUE TO SMALL PARTS/CHOKING
HAZARD.
WARNING

2
P/N 211737A 07/03
IMPORTANT!
Remove all contents from boxes.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY,
PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper
and complete assembly, use and supervision is essential for proper operation and to reduce the risk of
accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and
operated properly.
• Seat the pole sections properly (if applicable). Failure to do so could allow the pole
sections to seperate during play and/or during transport of the system.
• Climate, corrosion or misuse could result in system failure.
• If technical assistance is required, contact Huffy Sports.
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this unit.

07/03 P/N 211737A
3
Get to know the basic parts of your basketball system.....
SUPPORT
TUBE
TARP
MINI BASKETBALLS
SUPPORT
TUBES
BACKBOARD
RIM
NETTING

4
P/N 211737A 07/03
PARTS LIST AND IDENTIFIER
Item Qty Part No Description
1 2 202250 Support Pipe, Curved
2 2 202251 Support Pipe, Curved
3 3 202252 Threaded Stabelizer Pipe, Straight
4 4 202253 Support Pipe, White, Plastic
5 2 202254 Support Pipe, Straight
6 1 202255 Upper U-Pipe
7 1 202256 Lower U-Pipe, Angled Connectors
8 1 202257 Net
9 1 202258 Rim
10 1 202259 Tarp
Item Qty Part No Description
11 1 202260 Rim Bracket
12 2 202261 Adapter, White, Plastic
13 2 202262 Washer
14 2 202263 Shim Bracket, Threaded
15 2 202264 Wing Nut, Plastic
16 2 202265 Screw, 1-3/4"
17 6 202266 Screw, 1-3/8"
18 4 202267 Screw, 1/2"
19 1 202268 Backboard
20 2 202269 Mini Basketball
21 2 202298 Board Bracket with Hook
Item #12 (2)
Item #11 (1)
Item #7 (1)
Item #6 (1)
Item #1 (2) Item #2 (2)
Item #3 (3)
Item #5 (2)
Item #4 (4)
Item #8 (1)
Item #10 (1)
HARDWARE ID (ACTUAL SIZE)
Item #9 (1)
Item #19 (1)
Item #20 (2)
Item #17 (6) Item #18 (4)
Item #16 (2)
Item #13 (2)
Item #14 (2)
Item #15 (2)
Item #21 (1)

07/03 P/N 211737A
5
TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION
(actual size)
Phillips-Head Screwdriver
SECTION A: ASSEMBLE THE STAND AND TARP
2.
1. Attach lower U-pipe (7) to curved
support pipes (1).
1
17
17
1
7
10
1
7
3
Slide sleeve of the tarp (10) over
stabelizer pipe (3) and secure by
connecting stablizer pipe (3) to lower
U-pipe with screws (17).
Item #17 (6)
3

6
P/N 211737A 07/03
3.
4.
Slide curved support pipe (2) over curved support pipe (1)
NOTE: Locking pins on curved support pipe (2) MUST be
facing inward (toward eachother).
2
Connect threaded stablelizer pipe (3) using screws (17).
2
2
3
10
17
17
10
1
1
1
1

07/03 P/N 211737A
7
5. Attach straight bars (5) by snapping them over the pins of curved support pipes (2).
6. Connect threaded stablelizer pipe (3) using screws (17).
5
5
2
10
17
17 5
5
2
3

8
P/N 211737A 07/03
7. Slide upper U-pipe (6) over straight pipes (5).
NOTE: Locking pins on pipe (5) MUST snap into holes of upper U-pipe (6). See FIG. A.
8. Connect white, plastic pipes (4) together with plastic adapter (12).
NOTE: Keep pins of each pipe aligned.
FIG A.
6
5
6
5
4
4
4
4
12
12

07/03 P/N 211737A
9
9. Slide white pipe assembly through sleeve of tarp (10) and snap it into opening on lower
U-pipe (7). See FIG. A.
NOTE: Locking pins on pipe (4) MUST snap into holes of U-pipe (7).
4
412
10 FIG A.
7
10. Snap white pipe assembly into opening in upper U-pipe (6).
NOTE: Locking pins on white pipe (4) MUST snap into holes of upper U-pipe (6).
10
6
4
4
10
7

10
P/N 211737A 07/03
1
OUTSIDE VIEW
2
34
11. Install net (8) to rim (9).
12. Position rim bracket (11) inside
welded bracket extending from ring
of the rim (9).
19
9
11
98
Item #8 (1)
Item #9 (1)
TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION
(actual size)
Phillips-Head Screwdriver
SECTION B: ASSEMBLE THE BOARD AND RIM
Item #18 (4)
Item #16 (2)
Item #13 (2) Item #15 (2)