HULALA HOME NSPZ0916 User manual

HULALA
H O M E
01/26
NOTE:
This brochure contains IMPORTANT safty info. Please read and keep for future
reference.
ITEM NO.NSPZ0916

MAINTAINANCE AND WARNING
1.Keep furniture away from heat sources.
2.Do not clean furniture with harsh cleaner or polishes.Do not use
detergents,solvents,abrasives,spray packs or leather cleaner.
Use non-color mild soa with warm water to clean spills(Mix 1:10
soap to water).
3.Do not place furniture under direct sunlight,material will possibly
fade over time.
4.Do not use on site dry cleaning machine.Children should not climb
or jump on the furniture.
5.Do not write on furniture that is not protectedby a padded barrier.
6.Not for commercial use,only for residential use.
Weight Limitation
100 LBS
02/26

EXPLOSIVE VIEW
2PERSONEN
03/26

PARTS LIST
x1
x2
x1
x1
x1
x1
x1
x1
04/26
x1x2x1x1
x1x1x2x1

PARTS LIST
x1x1x2x1
05/26
x1x1

HARDWARE LIST
TOOL LIST
x1 x1
06/26
x12
M4
HARDWARE SPARE LIST
#1 x1
x4 x2 x24 x2 x2
x1 x4 x4 x4 x2 x4
Ø5/32''*1-1/4”
Ø8*1-1/4”
Ø8*1” Ø3.5*15mm
Ø3.5*15mm
Ø3.5*35mm Ø3.5*16mm

ASSEMBLY INSTRUCTIONS
STEP-1
1.Insert part (D) into part (E),make sure all holes align .
2.Insert panel (F＆D&E) into panel (C),make sure all holes alignedand
then tighten it with allen key #13 as picture show.
07/26
x1
M4
#13
1:
D
E
#13
#13
D
E
D&F
E

ASSEMBLY INSTRUCTIONS
STEP-2
Insert panel (H＆G) into panel (C),make sure all holes aligned and
then tighten it with allen key #13 as picture show.
x1
08/26
M4
#13
#13

ASSEMBLY INSTRUCTIONS
STEP-3
1.Insert side panel (B) into the corresponding hole of preassembled
step 2，make sure all holes aligned and use allen key #13 to tighten it
as picture show.
09/26
x1
M4
#13
#13
#13
#13

ASSEMBLY INSTRUCTIONS
STEP-4
1.insert back panel (I) into the groove of preassembled step 3,make
sure all holes aligned and use screw#1 to attach them ，tighten
screw #1 with screwdriver#14.
10/26
#1 x12 #14 x1
#14
#1x12
#1
#1
#1
#1
#1
#1
#1
#1
#1 #1
#1 #1

ASSEMBLY INSTRUCTIONS
STEP-5
1.insert part (J) into the preassembled step 4,make sure all holes
aligned and use screw#2 to attach them ，tighten screw #2 with
screwdriver #14.
11/26
#2 x4 #14 x1
#2
#2
#2 #2
#14

ASSEMBLY INSTRUCTIONS
STEP-6
1.insert part #7 into the preassembled step 2,make sure all holes
aligned and use screw #3 to attach them ，tighten screw #3 with
screwdriver#14.
x2 x1
12/26
#3 #14
x1
#14
#3
#3
#3

ASSEMBLY INSTRUCTIONS
13/26
STEP-7
1.Insert top panel (A ) into the corresponding hole of preassembled
step 6 ，make sure all holes aligned and use allen key #13 to tighten it
as picture show.
#13
x1
M4
#13
#13

ASSEMBLY INSTRUCTIONS
14/26
STEP-8
Attention:
Before the next step, adjust the
feet of the locker to keep it
level.

ASSEMBLY INSTRUCTIONS
x4 x1
15/26
STEP-9
1.Connect part (L&M) to part N using screw #4 and tighten it with
screwdriver #14.Slide in the part (O) into the groove in part (L&M).
make sure they are also in groove in part (N).
#4 #14
1:
2:
L
M
N
L
M
O
#14
#4x4
L&M
N

ASSEMBLY INSTRUCTIONS
STEP-10
Connect the (K) connection (L&M) using screw #4 , and tighten it with
screwdriver #14.
Use screw #6 to attach the handle #5 to panel K, tighten
screws with screwdriver #14.
x4 x1
16/26
#4 #14
#14
#4
#4
#5
#6
#6
#5
#14
#6 x1 #5 x1

17/26
ASSEMBLY INSTRUCTIONS
STEP-11

ASSEMBLY INSTRUCTIONS
x4 x1
18/26
STEP-12
1.Connect part (P&Q) to part N using screw #4 and tighten it with
screwdriver #14.Slide in the part (R) into the groove in part (P&Q).
make sure they are also in groove in part (N).
#4 #14
1:
P
Q
N
P
&
Q
N
#4x4
#14
P
Q
N
R

ASSEMBLY INSTRUCTIONS
STEP-13
Connect the (K) to part (P&Q) using screw #4 , and tighten it with
screwdriver #14.
Use screw #6 to attach the handle #5 to panel K, tighten screws with
screwdriver #14.
x12 x1
19/26
#4 #14
#14
#4
#4
#6
#5
#14
#5
#6
#6 x1 #5 x1

ASSEMBLY INSTRUCTIONS
x4 x1
20/26
STEP-14
1.Connect part (T&U) to part V using screw #4 and tighten it with
screwdriver #14.Slide in the part (R) into the groove in part (T&U).
make sure they are also in groove in part (V).
#4 #14
#4x4
#14