HULALA HOME TVSBSD0455 User manual

NOTE:
ITEM NO. TVSBSD0455
This brochure contains IMPORTANT safty info. Please read and keep for
future reference.
1/20

MAINTAINANCE
AND WARNING
Keep furniture away from heat.
Do not clean furniture with harsh cleansers
or polish. Do not use detergents, Solvents,
abrasives, spray packs or leather cleaner. Use
non-color mild soap with warm water clean
spills(Mix 1:10 soap to water)
Do not place furniture under direct sunlight,
material will possibly fade over time.
Do not use on site dry Cleaning machine.
Children should not climb or jump on the
furniture.
Do not write on furniture without a padded
barrier to protect the surface.
Not for commercial use, For residential use
only.
Weight Limitation
80LBS
20

PARTS
LIST
20

Explosive View
20
7

HARDWARE
LIST
Be sure to check all packing material carefully for
small parts, which may have come loose inside the
carton during shipment.
20
SPARE
16
24
88
M6*25mm

6 20
ASSEMBLY
INSTRUCTIONS
E*6
V*2
E*6
V*2
12
62
4
Prepare the part #7.
1）Separate metal slider to
part V and W as the
picture show.
3）Please note, before tighten
the screw E , need to check
the distance between the end
of metal slider to the edge of
part 7 must 15mm.
2) Attach the metal slider V to the part 7.
align the U hole in the metal
slider V to the pre-drilled screw hole
in part 7, screw in screw E
and tighten by screwdriver N.
Prepare the part #5 and #6.
1）Separate metal slider to
part V and W as the
picture show.
3）Please note, before tighten
the screw E , need to check
the distance between the end
of metal slider to the edge of
part 5 and 6 must 15mm.
2) Attach the metal slider V to the part 5
and 6.align the U hole in the metal
slider V to the pre-drilled screw hole
in part 5 and 6, screw in screw E
and tighten by screwdriver N.

20
7
A*4
D*4
O*4
B*4
A
D
Prepare the part 5 and 6
(continue) align the hole
in the pre-drilled hole in
part 5 and 6, insert the
wooden dowel D by hand
and screw in cam bolt A
by screwdriver N.
Assemble the part 15 and
16. align the hole in part 16
to the screw hole in part 15,
screw in the screw K and
tighten by Allenkey P.
Attach the part 5, 6 to the part 3. Align the hole in part 3, insert the
nut B into the hole in part 3 as the picture show, then insert the
wooden dowel D and Cam bolt A into part 3, tighten the nut B by
screwdriver N. at last, use the part O to cover the nut B.
Be sure the groove in part 5 and 6 at the same side !

20
A*4
D*4
B*4
O*4
D
Prepare the part 8 and 9. align the hole in part 8 and 9, insert
the wooden dowel D by hand, screw in Cam bolt A and tighten
by screwdriver N as the picture show.
Attach the part 8,9 to the part 4. Align the hole in part 4, insert the
nut B into the hole in part 4 as the picture show, then insert the
wooden dowel D and Cam bolt A in part 8 and 9 into part 4,
tighten the nut B by screwdriver N. at last, use the part O to cover
the nut B.
Be sure the groove in part 8 and 9 at the same side !

9 20
8
A*8
D*8
B*4
O*4
AD
Prepare the part 1. Align the hole in part 1, insert the wooden
dowel D by hand, screw in Cam bolt A and tighten by screwdriver X
as the picture show.
Step 8 Attach the part 1 to the finished part in
step 6. Align the hole in part 8 and 9, insert the
nut B into the hole in part 8 and 9 as the picture
show, then insert the wooden dowel D and Cam
bolt A in part 1 into part 8 and 9, tighten the nut B
by screwdriver X. at last, use the part O to cover the nut B.

20
9
10
O*4
B*4
C*4
A*4
D*4
D*4
Install the part 10 and 11 into finished part in step 8.
1）Prepare the part 11. install the part Q into part 11 by hand.
2）Slide the part 10 and 11 into the groove in part 8, 9 and 1.
3）Insert the wooden dowel D into part 8 and 9 by hand as the
picture show.
Attach the part 5 and 6 to the finished
part in step 9.
1) Insert the nut B into part 5 and 6 as the
picture show.
2) Slide the part 10 and 11 into the groove
in part 3，5 and 6, at the same time, Align the
hole in part 3, insert the wooden dowel D
and Cam bolt A in part 1, 8 and 9 into
part 3, 5 and 6. tighten the nut B by
screwdriver N, at last use part O cover
the nut B.
1
3) Align the hole in part 3 to the hole in
part 8 and 9, screw in the screw C and
tighten by Allenkey P.
4) Assemble the wooden dowel D and Cam
bolt A into the part 3, 5 and 6. align the hole in the
part 3, 5 and 6, insert the wooden dowel D by hand,
screw in the cam bolt A by screwdriver N.

11 20
11
12
7
AD
O*4 B*4
Attach the part 7 to the finished part in step 10. insert the nut B into part 7,
align the wooden dowel D and cam bolt A into part 7, tighten the nut B by
screwdriver N. then cover the nut by part O.
Slide the part 17 into the groove in part 3, 5, 6 and 7. then insert the
wooden dowel D into part 7 as the picture show.
6
D*4

12 20
13
14
7
C*8
J*12
Attach the part to the finished part in step 12. Align the hole in the part 2
to the hole in part 5, 6 and 7, insert the wooden dowel in part 5,6 and 7,
screw in the screw C and tighten by Allenkey P.
Attach the part 16 to the part 12, then attach the part 12 and 13 to the part 2.
1) Align the hole in part 12, screw in the screw I and tighten by Allenkey P.
PLS NOTE DO NOT FULLY TIGHTEN!
2) ) Align the hole in part 12 and 13 to the hole in part 2, then
screw in the screw j and tighten by Allenkey P.
PLS NOTE DO NOT FULLY TIGHTEN!

13 20
15
16
U
U*2
U*2 U
E
Install the part U. align the hole in part U to the hole in part 12, 13,
screw in the screwE and tighten by screwdriver N.
DO NOT FULLY TIGHTEN!
Assemble the part 14 to the part 12 and 13.
Align the hole in the part 14 to the hole in part U, screw in the
screw E and tighten by screwdriver N.
Check all screw I, J, E are in the right position, then Fully
tighten the screw I, J and E in sequence.

17
14 20
24
28
Assemble the part F and part hook of anti-collapse R as the picture show.
1） Insert the part F into the space between the part 5,6,10,11 and 17. screw in screw E
and tighten by screwdriver N.
2）Align the hole in part R to the part 1, screw in and tighten the screw E by screwdriver N.
5

15/20
18
Install the door.
1) Insert the wheel in part N into the groove in part 2 in 30° angle as the picture show
2) Push the part 18 towards the cabinet,
3) Move the door to the corner, push out the tongue of the part N to hole in part 1 to fix
the door.as the picture show
3
1
3

19
16/20
20
M
M*4
M
Prepare the drawers(1).
Align the hole in part 19, screw in and tighten the cam bolt A by screwdriver X.
Align the hole in the part 19 to the hole in part H, screw in and tighten the screw G by
screwdriver X.
Attach the part 20 and 21 to the part 22. Align the hole in part 20 and 21 to the hole in
part 22, screw in and tighten the screw M by screwdriver X.
Prepare the drawers(2)
Slide in the part 23 into the groove in part 20, 21 and 22.
Attach the part 19 to the finished part in above step. Insert the nut B into the hole in
part 20 and 21 as the picture show, then insert the cam bolt A, tighten nut B by
screwdriver X. last cover the nut by part O.

21
17/20
22
W*2
E*4
x18
Prepare the drawers(3).
Attach the metal slider part W to
the part 20 and 21 as the picture
show.
1) Find the right direction of metal
slider W. Metal slider W has two ends,
one is open , another is close .Make sure
the close end to the part 19 while install !
2) Align the U hole in metal part W to the hole in part 20
and 21, screw in and tighten the screw E by screwdriver X
3) The metal slider W can be adjusted up and down after
loose screw E while it is needed.
Put the drawer into cabinet
1) Align the metal slider W to the metal slider V, then push the drawer
into cabinet as the picture show.
2) You can adjust the space between drawer and cabinet according to
the way in step 21 3).

Use the adjustable nail to keep the cabinet level in case the
cabinet is wabbling.
Now your cabinet is ready to use.
23
18/20

19
Install the anti-collapse device.
1. Mark the position on the wall, this should be same as the position of R
where are on the back of panel 1; Drilled and insert the expandable screw
T by hammer;
2.Assemble the part R on the wall. Align the hole in the part R to the
expandable screw T, screw in and tighten by screwdriver;
3.let the plastic belt S go through the both R and pull to tighten.
M
M
T
T
24
20

Are you having
with assembly? Missing
send email with your order
For return, Please check the return policy
the retailer or MarketPlace you bought
Appreciated your purchasing from us.
Pop up your life by our furniture
20/20
We strive to offer high-quality products, and we also try our
best to satisfy each and every customer that orders from us
with product or service as needed. We provide 30 days
warranty starting from the time you receive the item. Each
customer must provide a record of their order such as the
order number, or item receipt for any items that are out of
the warranty period you may also still receive replacement
parts by purchasing them with our company if they are
available.