Hunter ICC2 User manual

ICC2
MODULAR RESIDENTIAL AND COMMERCIAL
IRRIGATION CONTROLLER
Owner’s Manual
• I2C-800-PL: 8-station base model, expandable to 38 stations, plastic outdoor cabinet
• I2C-800-M: 8-station base model, expandable to 54 stations, gray metal outdoor cabinet
• I2C-800-SS: 8-station base model, expandable to 54 stations, stainless steel outdoor cabinet
• I2C-800-PP: 8-station base model, expandable to 54 stations, plastic pedestal
Date/TimeSystem O
Start Times
Run Times
Water Days
Solar Sync®
Manual
Seasonal Adjust

4hunter.direct/ICC2help
Specications
Specications
OPERATING SPECIFICATIONS
• Number of Stations: Modular design expandable from
8 to 38 (plastic), 8 to 54 (metal)
• Station Run Time: 1 minute up to 12 hours
• Start Times: 8 per program, 4 independent
programs (A, B, C, and D)
• Simultaneous Program Operation: 2
• Sensor Inputs: 1
• Pump/Master Valve Outputs: 1
• Watering Schedule: 7-day calendar, interval watering up
to a 31-day interval or true odd or even day programming
DIMENSIONS
PLASTIC CABINET
• Height: 12" (30.5 cm)
• Width: 13.7" (34.8 cm)
• Depth: 5" (12.7 cm)
METAL CABINET GRAY OR SS
• Height: 16" (40.6 cm)
• Width: 13" (33 cm)
• Depth: 5" (12.7 cm)
METAL PEDESTAL GRAY OR SS
• Height: 36" (91.4 cm)
• Width: 11.5" (29.2 cm)
• Depth: 5" (12.7 cm)
PLASTIC PEDESTAL
• Height: 39" (99.1 cm)
• Width: 24" (61 cm)
• Depth: 17" (43.2 cm)
ELECTRICAL SPECIFICATIONS
• Transformer Input: 120 VAC, 60 Hz
(230 VAC, 50/60 Hz international use)
• Transformer Output: 24 VAC, 1.4 A
• Station Output: 24 VAC, up to 0.56 A
• Pump/Master Valve Output: 24 VAC, up to 0.56 A
• Battery: 9-volt alkaline battery (not included) used only
for non-AC programming; non-volatile memory maintains
program information
• Front Panel Battery: Internal CR2032 lithium (included)
for real-time clock
APPROVALS
• CE, UL, cUL, FCC, RCM
• Plastic Cabinet: IP44, NEMA 3R
• Metal Cabinet (Gray or SS): IP44, NEMA 3R
• Metal Pedestal (Gray or SS): IP44, NEMA 3R
• Plastic Pedestal: IP24, NEMA 3R
DEFAULT SETTINGS
• All stations are set to zero run time. This controller has a
non-volatile memory that retains all entered program data
even during power outages, without the need for a battery.

Built on Innovation®5
Components
Date/TimeSystem O
Start Times
Run Times
Water Days
Solar Sync®
Manual
Seasonal Adjust
ICC2 Components
DISPLAY SCREENS
1. Station Running: Indicates when watering occurs.
2. Sprinkler O Days: Indicates watering will not occur on
selected day.
3. Program Indicators: Identies the program in use (A, B,
C, or D).
4. Water Days Symbol: Choose desired watering days.
5. Solar Sync Symbol: Indicates optional Hunter Solar Sync
sensor is in use.
6. Days of the Week: Monday–Sunday.
7. Season Adjust %: Indicates seasonal adjustment
percentage (increments of 5%).
8. Time Mode (AM/PM/24): Select AM, PM, or 24 HR
display.
9. Rain Sensor Active/Override: Indicates if sensor is set to
active or bypass.
10. Run Time Symbol: User can set each station run time from
1 minute to 12 hours.
11. Start Time Symbol: Schedule up to 8 start times per
program in 15-minute increments.
12. Odd/Even/Interval Days: Indicates if odd, even, or interval
watering days are selected.
CONTROL BUTTONS
+Plus Button: Increases selected ashing display.
- Minus Button: Decreases selected ashing display.
►Forward Arrow: Advances selected ashing display to the
next item; also use to start manual cycle.
◄Back Arrow: Returns selected ashing display to the
previous item.
PRG Program Button: Selects and programs (A, B, C, or D);
also used to start a test program.
RAIN SENSOR Sensor Bypass Switch: Use to bypass optional
Hunter “Clik-type” sensors.
Control Buttons
Sensor Bypass Switch











6hunter.direct/ICC2help
Components
Date/TimeSystem O
Start Times
Run Times
Water Days
Solar Sync®
Manual
Seasonal Adjust
CONTROL DIAL
1. Run: Normal dial position for automatic operation.
2. Date/Time: Set current date and time.
3. Start Times: Set 1 to 8 start times in each program.
4. Run Times: Set each station run time.
5. Water Days: Select individual, odd, even, or interval
watering days.
6. Pump: Turn pump or master valve on or o for each
station.
7. Seasonal Adjust: Change all run times in all programs by a
percentage (5% to 300%).
8. Solar Sync: Set up and adjust option for Hunter Solar
Sync sensor.
9. Manual: Immediately activate a one-time watering of a
single station.
10. System O: Used to stop all watering until the dial is
returned to the RUN position.
Date/TimeSystem O
Start Times
Run Times
Water Days
Solar Sync®
Manual
Seasonal Adjust

 

 



Built on Innovation®7
Components
WIRING COMPARTMENT
1. Facepack/Control Panel: Primary console for
programming the controller.
2. Power Module: Provides power to the controller and must
be in place for controller to operate; contains 24 VAC,
sensor, remote, and P/MV terminals.
3. SmartPort Connector: Enables use of Hunter ROAM and
ROAM-XL remotes.
4. Transformer: Pre-installed with 120 VAC, 230 VAC, neutral,
and ground wires (includes additional earth grounding lug
for supplemental lighting protection).
5. Battery Compartment: Without AC power, a 9-volt battery
(not included) allows programming, while a 3-volt CR2032
lithium battery (included) keeps real-time clock.
6. Ribbon Cable: Connects facepack to power module, and
transmits information from the control panel to the inner
controller assembly.
7. Station Output Modules: Plug-in station modules used to
expand controller capacity in increments of 4, 8, and 22
stations (ICM-400, ICM-800, and ICM-2200).
8. Door Lock: Pre-installed lock assembly with 751 key
(alternative 701, 702, or 703 key/lock assemblies also
available).
PLASTIC CABINET
METAL CABINET

















8hunter.direct/ICC2help
Mounting the Controller
Mounting the Controller
PLASTIC CABINET WALL MOUNTING
1. Remove door and control panel for easier access. Use the
enclosed hole template to mark and drill mounting holes.
Be sure to leave enough room to open the door. Install
screw anchors if attaching to drywall or masonry wall.
2. Secure a 1" (25 mm) screw into the wall, leaving ¼" (6 mm)
free of the wall. Slide the top center keyhole on the rear of
the controller over the screw and hang the cabinet on the
screw head.
-Drill four pilot holes for the remaining mounting screws.
-Secure the controller in place by installing screws in the
four remaining holes from inside the cabinet. Re-attach
the control panel and the door.
Wall Mounting
Wall Mounting, plastic box.2
Wall Mounting, plastic box.2

Built on Innovation®9
Mounting the Controller
METAL CABINET WALL MOUNTING
1. Remove door and control panel for easier access. Use the
enclosed hole template to mark and drill mounting holes.
Be sure to leave enough room to open the door. Install
screw anchors if attaching to drywall or masonry wall.
2. Secure a 1" (25 mm) screw into the wall, leaving ¼" (6 mm)
free of the wall. Slide the top center keyhole on the rear of
the controller over the screw and hang the cabinet on the
screw head.
-Drill four pilot holes for the remaining mounting screws.
-Secure the controller in place by installing screws in the
four remaining holes from inside the cabinet. Re-attach
the control panel and the door.
Wall Mounting
Wall Mounting, Metal box.3
Wall Mounting, Metal box.3

10 hunter.direct/ICC2help
Mounting the Controller
METAL PEDESTAL MOUNTING
1. ICC-PED or ICC-PED-SS
2. ICC Pedestal Door
3. Pedestal Mounting Template
4. Nut, #10-32 (qty: 2)
5. Screw, #10-32 x ⁄" (qty: 2)
6. Lock
7. Pedestal Mounting J-Bolt (qty: 4)
8. Nut, Hex ⁄" (qty: 8)
9. Washer, Flat ⁄" (qty: 8)
10. 2" Conduit Nipple
11. 2" Conduit Locknut
12. Hex Nut, Door Lock
13. ⁄" Conduit Coupler
14. ⁄" Conduit Nipple















Built on Innovation®11
Mounting the Controller
PREPARE THE CONCRETE
1. Prepare a form for a concrete pad, approximately
20" W x 16" D x 4" H (50 cm W x 40 cm D x 10 cm H) at grade
level. Slope the concrete downward away from the pedestal.
2. Install the J-bolts and wire sweeps (power supply, ground
wire, and irrigation control conduits) in the template and
position them in the opening.
3. Remove the pedestal door and attach the base of the
pedestal to the J-bolts in the concrete slab.
INSTALL CONTROLLER ON THE PEDESTAL
Before installing controller to pedestal, ensure all necessary
conduit plugs are removed from the bottom of the controller.
1. Secure the controller by inserting 2" conduit nipple up
through the top of the pedestal into the bottom of the
controller, and tighten the locknut on the threads.
2. Remove the wiring compartment cover from the front of
the transformer junction box, and secure the controller
with ⁄" conduit coupler and nipple.
3. Insert two #10-32 screws down through screw holes on
the bottom right side of the cabinet, and tighten with
corresponding nuts.

  

PLASTIC PEDESTAL MOUNTING
1. Mount the irrigation controller pedestal to the
concrete form.
2. Electrical supply conduit: Connect to power source;
J-box inside controller.
3. Ground wire conduit: Ground per ASIC guidelines.
4. Run irrigation control wire through conduit per local codes.
5. Pedestal base per plan: Ensure positive drainage away
from pedestal.
Note: Controller shall be hardwired to grounded 120 VAC or
230 VAC (international) power source.

12 hunter.direct/ICC2help
Connecting AC Power
Connecting AC Power
1. Turn o AC power at the source and verify it is o.
2. Disconnect the facepack ribbon cable, and remove the
facepack from the cabinet.
3. Remove the screw and wiring compartment cover from
the front of the transformer junction box.
Wiring Controller Power
Wiring Controller Power
Wiring Controller Power