Hunter Hunter Ceiling Fan User manual

www.HunterFan.com 1.888.830.1326
30 inches
7 feet
PAGE
2
What to Expect with
Your Installation Ceiling Plate
Ladder
PAGE
3
Tools Needed
Hanging the Fan
PAGE
9
Canopy
Table of Contents
PAGE
8
PAGE
18
Maintenance,
Operation & Cleaning Troubleshooting
?
?
?
PAGE
16
PAGE
5
Top Housing
PAGE
4
Wiring
PAGE
13
Light Kit
PAGE
12
Switch Housing
Blades
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or ofce for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
Remote Control
PAGE
15
PAGE
7
1
M3552-01 • 05/14/14 • © Hunter Fan Company
PAGE
11

www.HunterFan.com 1.888.830.1326
If you are installing multiple remote-controlled fans on
the same circuit breaker, you may need to perform a few
extra steps to prevent interference or faulty operation of
your remote controls.
Go to www.HunterFan.com/FAQs and click
“How do I properly install multiple remote-controlled fans?”
for more information.
M3552-01 • 05/14/14 • © Hunter Fan Company
1.888.830.13261.888.830.1326
What to Expect with Your Installation
Know your wiring
If you are unfamiliar
with wiring, use a
qualied electrician.
Assess location
30 inches
from blade tip
to nearest wall
or obstruction 7 feet
from bottom
edge of blade
to the oor
You may need a
friend to help you.
Check box to see
fan weight
Must be able to
secure the fan to
building structure or
fan-rated outlet box
2
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
CAUTIONS
w.1 - To reduce the risk of re, electrical shock, or personal
injury, mount fan directly from building structure and/or an
outlet box marked acceptable for fan support of 70 lbs (31.8 kg)
and use the mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or
servicing your fan, disconnect the power by turning off the
circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off
position, securely fasten a prominent warning device, such as a
tag, to the service panel.
w.3 - To reduce the risk of re, electrical shock, or motor damage,
use only Hunter Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade
brackets when installing the blade brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring,
use a qualied electrician.
c.2 - Use only Hunter replacement parts.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications.

www.HunterFan.com 1.888.830.1326
Tools Needed
Power Drill
(optional)
9/64” Drill Bit
(optional)
Ladder Screwdrivers
Wire Strippers
If mounting to a support structure, you will also need these tools.
3
M3552-01 • 05/14/14 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
4
M3552-01 • 05/14/14 • © Hunter Fan Company
1.888.830.1326
Ceiling Plate
Refer to warning w.1 on pg. 2
To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to the
outlet box associated with the wall switch location.
OFF
Turn Power
Use wood screws
(included) when securing
to support structure with
approved electrical outlet
box. Drill 9/64” pilot holes
in support structure to aid
in securing ceiling plate
with hardware found in
the hardware bag.
Use machine screws
(provided with outlet
box) when securing to
existing ceiling fan-rated
outlet box. Make sure
it is securely installed
and is acceptable for fan
support of 31.8 kg (70 lbs)
or less.
Make sure all four (4) bumpers are
still attached.
Bumper

www.HunterFan.com 1.888.830.1326
5
M3552-01 • 05/14/14 • © Hunter Fan Company
Top Housing
Rest the trim ring on the top
housing.
Trim Ring
Place the top housing onto the
motor housing so that the holes
in the top housing lineup with
the holes in the motor housing.
Top Housing
Thread the wires through the
top housing.
Place the canopy on the top
housing. Ensure all four screw
holes line up with the screw
holes in both the top housing
and the adapter.
Canopy
Adapter

www.HunterFan.com 1.888.830.1326
Install the top housing screws. Install the
grounding screw in the smaller screw
hole. These screws can be found in the
hardware bag.
Grounding
Screw
Top Housing
Screws
Top Housing (continued)
8” 3/8”
8”
3/8”
C
U
T
&
S
T
R
I
P
(not to scale)
The wires can be cut, but leave at
least 8” extending from the top of
the canopy.
6
M3552-01 • 05/14/14 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
7
M3552-01 • 05/14/14 • © Hunter Fan Company
Hanging the Fan
Raise the fan and align the slots in the
canopy with the hooks on the ceiling plate.
Note: Fan style may vary.
Place the slots over the ceiling plate
hooks to hang the fan.
Ceiling
Plate Hook
Ceiling
Plate
Hook
Note: To hang the fan, you must tilt the
canopy to an almost vertical position so that
the canopy slots sit on the ceiling plate hooks.

www.HunterFan.com 1.888.830.1326
Wiring
Turn the splices upward and push them carefully back through the ceiling plate into
the outlet box. Spread the wires apart, with the grounded wires on one side of the
outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
F
R
O
M
C
E
I
L
I
N
G
F
R
O
M
C
E
I
L
I
N
G
P
L
A
T
E
green/yellow stripe (grounding)
green
Using an orange
wire connector from
the hardware
bag, connect the
3 grounding wires
(green, green/
yellow stripe, or bare
copper) coming
from the ceiling and
ceiling plate.
F
R
O
M
R
E
C
E
I
V
E
R
black blue
yellow blue
Note: To connect the
wires, hold the bare
metal leads together and
place a wire connector
over them, then twist
clockwise until tight.
Using the orange
wire connectors
from the remote
control hardware
bag, connect the blue
wire from the receiver
to the blue wire (or
possibly black with
white stripe wire) from
the fan. Connect the
yellow wire from the
receiver to the black
wire from the fan.
F
R
O
M
F
A
N
F
R
O
M
R
E
C
E
I
V
E
R
Using the orange wire
connectors from
the hardware bag,
connect the black wire
(ungrounded) from
the ceiling to the black
wire from the receiver.
Connect the white
wire (grounded) from
the ceiling to both the
white wire from the
receiver and the white
wire from the fan.
F
R
O
M
C
E
I
L
I
N
G
black (ungrounded) white (grounded)
black white
F
R
O
M
F
A
N
white
8
M3552-01 • 05/14/14 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
9
M3552-01 • 05/14/14 • © Hunter Fan Company
Canopy
Hold the canopy up with the screw holes
aligned. Partially install two canopy
screws, found in the hardware bag, into
the holes opposite the ceiling plate hooks.
Partially install a canopy screw, found
in the hardware bag, between the
ceiling plate hooks. When all the holes
are properly aligned, securely tighten all
three canopy screws.
Screw
Holes
Canopy
Screw
Canopy
Screw
Swing the fan up to align the canopy
screw holes with the mounting holes on
the ceiling plate.
Ceiling
Plate Hooks
Note: The slots in the canopy must
remain engaged while swinging the
canopy for alignment.

www.HunterFan.com 1.888.830.1326
Using both hands, push the canopy trim ring
up to the top of the canopy. The canopy trim
ring will snap and lock into place.
Note: Should you need to remove the trim
ring, press rmly on opposite sides of the trim
ring. The tabs will ex out releasing the
canopy trim ring.
Canopy
Trim Ring
Canopy (continued)
10
M3552-01 • 05/14/14 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
M3552-01 • 05/14/14 • © Hunter Fan Company
Blades
11
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the nishes.
Attach each blade to a blade iron using four
blade washers, found in the hardware
bag, and four blade assembly screws, found
in the hardware bag.

www.HunterFan.com 1.888.830.1326
Switch Housing
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing xture falling.
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
Screw two housing assembly screws
from the hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Insert the third screw, found in
the hardware bag, into place and
then tighten all three screws.
12
M3552-01 • 05/14/14 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
13
M3552-01 • 05/14/14 • © Hunter Fan Company
Light Kit
Partially install two of the switch housing
screws found in the bag. Connect
the plugs from the upper and lower
switch housings. Make sure to line up the
colored markings on the connectors.
Align the keyhole slots in the light kit
housing with the switch housing screws.
Make sure all the wires from the fan and
the light kit are snug inside the center of
the light kit, not pinched in between the
upper switch housing and the light kit or
hanging out of the sides.
Turn the light kit counterclockwise until
the switch housing screws are rmly
situated in the narrow end of the keyhole
slots. Install the remaining screw into the
housing. Tighten all three screws securely.
Switch
Housing
Screw
Make sure the light kit is securely attached to the upper
switch housing. Failure to properly secure all three assembly
screws could result in the light xture falling.

www.HunterFan.com 1.888.830.1326
Light Kit (continued)
CONGRATULATIONS!
YOU’RE DONE!
See next page for fan
operation instructions.
Position the notches in the outer
rim of the globe so they line
up with the tabs on the inside
surface of the light xture rim.
Install a light bulb in each socket.
When necessary, replace with
bulbs of the same wattage.
Bulb
Notch
Tab
Carefully lift the globe up inside
the light xture as far as it will go.
Rotate the globe in a clockwise
direction until it is held tightly in
place by the three tabs.
M3552-01 • 05/14/14 • © Hunter Fan Company
14

www.HunterFan.com 1.888.830.1326
Remote Control
Note: The remote must be paired before the
fan will operate.
Within 3 minutes of restoring power to the
fan, press both the Fan Off button and the High
button for at least 4 seconds. Your fan will turn on
low to indicate successful syncing. If it does not,
turn off power to your fan, wait 1 minute then try
again. If using the transmitter with multiple fans,
repeat this process for each fan.
Fan Off
High
To access the battery compartment, remove
the small Phillips head screw that secures the
battery door to the transmitter assembly. The
battery should be installed with the positive
(+) side up. Replace with a CR2032 battery
when necessary.
Phillips
Head
Screw
Battery
Door
ON
Turn Power
If you are installing multiple remote-controlled fans on
the same circuit breaker, you may need to perform a few
extra steps to prevent interference or faulty operation of
your remote controls.
Go to www.HunterFan.com/FAQs and click
“How do I properly install multiple remote-controlled fans?”
for more information.
15
M3552-01 • 05/14/14 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Rocker- Style
Plate
Switch Cover Plate
Removed
Tabs
To install the transmitter cradle, remove the
two screws holding the switch cover plate. Do
not remove the cover plate. Orient the cradle
by lining up the two mounting holes with
those on the cover plate. Insert and tighten
the screws. Do not over tighten.
Note: For rocker-style cover plates, break off
the tabs by pushing outward.
To turn on fan, press a fan speed button. Speeds
range from off (0) to high (3). Quickly press the
Light button to turn the lights off and on.
Medium
Speed
Light
High
Speed
Fan
Off
Low
Speed
To switch the direction of air ow, move the
reverse switch to the opposite position.
Reverse
Switch
Maintenance, Operation & Cleaning (continued)
16
M3552-01 • 05/14/14 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Maintenance, Operation & Cleaning (continued)
Cleaning the fan - Use soft
brushes or cloths to prevent
scratching. Cleaning products
may damage the nishes.
ON
Turn Power
Safe-Exit
• Press the Fan Off button for at least three seconds to
initiate the Safe-Exit Mode.
• The lights will ash for visual conrmation.
• The lights will stay on 50% brightness for 15 seconds and
then begin to dim. After a total of 30 seconds, the lights
will be completely off.
The Safe-Exit Program gives you about thirty seconds
of light when you turn the lights off to exit the room
before the lights go out.To use Safe-Exit:
Note: For CFL lighting, the lights will stay on 100%
brightness for 30 seconds. After a total of 30 seconds, the
lights will be completely off.
17
M3552-01 • 05/14/14 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Troubleshooting
Lights dim when turned on or
do not turn on at all.
• Make sure the wattage of the
light bulbs installed matches
the specications on the light
sockets.
Fan doesn’t work
• Make sure power switch is on.
• Push the motor reversing switch
rmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 8.
• Check the plug connection in
the switch housing.
Excessive wobbling
• Make sure the blades are
securely attached to the
blade irons according to the
blade assembly instructions
provided.
• Use the provided balancing
kit and instructions to
balance the fan.
Remote control of fan is erratic
• Make sure the battery is
installed correctly.
• Install a fresh battery.
Transmitter only works when
held at close range
• Change battery.
Noisy operation
• Check to see if any of the blades
are cracked. If so, replace all of
the blades.
If you have multiple remotes or
multiple remote-controlled fans
installed on the same circuit
breaker and you are experiencing
interference or faulty operation of
your remote controls, please go to
www.HunterFan.com/FAQs
and click “How do I properly install
multiple remote-controlled fans?”
for information on how to correct
this issue.
18
M3552-01 • 05/14/14 • © Hunter Fan Company