HW Group Poseidon 4002 User manual

Poseidon 4002
MANUAL

Poseidon 4002 –Manual
HW group
www.HW-group.com

Poseidon 4002 –Manual
HW group
www.HW-group.com
Poseidon 4002 MANUAL
INPUTS
Binary inputs 1–6
(for contacts)
POWER input
12VDC supply
(jack or terminals)
ETHERNET
10 or 100/10 Mbps
DIP switch
Configuration switches, default is
Off, Off.
OUTPUTS
Two 50V rated switch-
over relay contacts
POWER OUT
12V supply for sensors
SENSORS
S1 to S4 ports for connecting sensors up
to 30m away total for each port.
POWER OUT
12V supply, terminal block
GSM MODEM
RS-232 port for
connecting a modem
POWER OUT
12V for sensors and GSM
modem

Poseidon 4002 –Manual
HW group
www.HW-group.com
1-Wire sensors wiring
Recommended connections
Det Control
PowerEgg
- Power detector
- Power control
Remote reset
10m
°C
°C
°C
%RH
Temperatue probe 3m
Temperature probe
for Rack montage
Closed Door detector
Dry Contact input
Smoke detector
Water Leak detector
AirFlow detector
Temperature &
Humidity probe (Rack)
SMS
RS-232
GSM modem
I1 I6 O1 O2S1 S2 S3 S4

Poseidon 4002 –Manual
HW group
www.HW-group.com
First steps
1) Connecting the cables
Turn the unit upside down and write down its MAC address
that is printed on the label.
Set the switches: DIP1=Off, DIP2=Off.
Connect the unit to the Ethernet (with a patch cable to a
switch, cross-over cable to a PC), RJ-45 port.
Plug the power adapter into a mains outlet and connect it to
the Poseidon power jack.
The green POWER LED lights up.
If the Ethernet connection works properly, the LINK LED lights up after a short while, and then
flashes whenever data is transferred (activity indication).
2) Configuring the IP address –UDP Config
UDP Config –root directory of the supplied CD (Windows and Linux versions).
Download from www.HW-group.com Software > UDP Config.
Click the icon to launch UDP Config - automatically search connected devices.
Device search works in local network only.
Individual units are identified by MAC addresses (label at the bottom side of the unit).
Double-click a MAC address to open a basic device configuration dialog.
Poseidon 4002
Doubleclick

Poseidon 4002 –Manual
HW group
www.HW-group.com
First steps
Configure network parameters
IP address / HTTP port (80 by default)
Network mask
Gateway IP address for your network
Device name (optional)
Click the Apply Changes button to save the
settings.
You may also use the following utilities to configure the IP address:
UDP Config for Linux
RS-232 serial port (any terminal program, 9600 8N1, DIP1=ON, restart)
IMPORTANT:
To reset the device to factory defaults, toggle DIP1 several times within 5 seconds after
power-up.
No configuration changes can be stored while DIP2=On. To change the IP address, set
DIP2=Off.

Poseidon 4002 –Manual
HW group
www.HW-group.com
First steps
4) WWW interface of the device
To open the WWW interface of the device:
oEnter the IP address into a web browser
oClick the IP address in UDP Config
oClick the underlined IP address in UDP
SETUP
The WWW page displays current states of inputs and outputs.
Click the “Graphic Flash SETUP” link to open the graphical configuration interface (Flash
Setup).
Detailed configuration in
“Flash Setup”
Device name
Description of the
values.XML file
Device IP address
Description of SNMP
structures in the MIB /
OID list
Overview of
dry contact inputs
Outputs overview and
states
Overview of connected sensors, their
unique IDs and current readings
Firmware update

Poseidon 4002 –Manual
HW group
www.HW-group.com
Flash SETUP
To open the FLASH interface, FLASH support needs to be installed on your PC. If the computer is
connected to the Internet, the needed plug-in is downloaded automatically.
General: Overview of current readings
General Setup: IP address, DNS, security (username/password or IP range)
SNMP: SNMP / SNMP Trap configuration (ports and alarm recipients)
Email & SMS: Configuration and test
Log & Time: Time configuration, NTP server
Sensors: Device name, sensor names, status overview
Outputs: Control and mode configuration of outputs
System: Firmware upgrade
Refresh function in the main tab controls the update interval for displaying new sensor readings.
User-defined names
for sensors and inputs
Control of outputs (handle unlocking)
Alarm thresholds
Action when value
out of range
E-mail configuration and testing

Poseidon 4002 –Manual
HW group
www.HW-group.com
Email & SMS
Warning: Configuration changes must be confirmed by clicking the Apply Changes button.
Sends a test e-mail and
shows the connection log
Sends a test SMS and
shows the connection log
1) Correct Gateway IP address
2) DNS server in network settings
3) SMTP server and port
4) Authentication turned on, correct
username and password
5) Spam filter for your mailbox is
disabled
1) Supported GSM modem connected
with the supplied cable
2) SIM card inserted in the GSM
modem, deactivated PIN
3) GSM modem turned on
4) GSM SMS interface enabled,
modem status is “Ready”
5) Displayed SMS Center number
(retrieved from SIM)
To send e-mail, check:
To send SMS, check:

Poseidon 4002 –Manual
HW group
www.HW-group.com
Sensors
Warning: Configuration changes must be confirmed by clicking the Apply Changes button.
Enter sensor name, will be
shown in E-mail, SMS or
SNMP traps
Sends a SNMP trap if the “Safe
Range” for this sensor is exceeded
Scans connected sensors and
displays detected sensors
Sends a SMS if the “Safe Range”
for this sensor is exceeded
To avoid numerous false alerts
(by e-mail or SMS) whenever the reading
fluctuates around the threshold,
you can use:
1) Hysteresis Idle Range
Tolerance band around the
“Safe Range”. Prevents
multiple alarm alerts.
2) Delay [s]
Delays the information about
alarm beginning and alarm
end by a specified time. Can be
used for binary contacts, too.
Tip: For details, see the complete “Poseidon family” manual.