Hwasung 054 Series User manual

Technical manual
(User Manual)
HMK-054 HMB-054 HMV-054
HMK-054
HMB-054
Control board +
Mechanism combination
Release 2
HMV-054
Vertical Type

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.1
CAUTION
Please do not disassemble / reorganize the product.
Please do not the remove the paper jam during power on.
Pleased do not exceed the standard power voltage.
Please do not wash off the product.
Please do not press / shock the product.
Please do not put the product at the moist (humid) condition.
Please contact us if there is any problem.
Please power off once remove the paper jam.
Please clear the air / open the disclosed place.
Please set the product without damage enviornment.
Please set the product at the stable place.
Pleaes keep the requires as necessary as general electrics.

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.2
CONTENTS
1.Printer features & External dimension 3
1-1) Name of each parts 3
1-2) Model number 5
1-3) Dimension 6
2. Operation 9
2-1) Setting a paper (Auto loading,Clam shell) 9
2-2) Removing the paper jam 11
2-3) Self test 11
2-4) HEX Dump 12
2-5) Update (Onboard) 13
2-6) Memory Switch 14
2-7) Rebooting the firmware 16
2-8) Dip Switch 19
2-9) Conntector (internal) 20
3. General Specification 22
3-1) Specification 22
3-2) FONT 22
3-3) Buffer (Internal) 22
3-4) Electrical Specification 22
3-5) Operation Environment 22
3-6) Storage environment 22
3-7) MCBF 22
3-8) Weight 22
4. Interface 23
4-1) RS-232C 23
4-2) USB 23
5. Command 24
6. USB 56
6-1)DLL interface 56
6-2)DLL Causion for Using 57
6-3) OCX Driver 58
6-4) OCX Notice 61

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.3
1. Printer features & External dimension
1-1) Name of each parts
1. Auto cutter
2. Paper guide
3. Head up lever
4. Neae end sensor
5. Paper shaft
6. Power connector
7. Interface connector
8. Power switch
9. Feed button
10. Power LED(Green)
11. Error LED (Red)
12. Dip swtich (Bottom)
1
2
3
4
5
6
7
8
9
10
11
12
(+)
(-)
Power connector (24V)
[HMK-054]

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.4
8
9
10
11
7
6
(+)
(-)
[HMB-054]
Power connector (24V)

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.5
1-2) Model Number
HM□-054
※Model
K : Kiosk type (KIOSK)
B : Control board + Mechanism combination
V : Vertucal Type
C : Control board Type

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.6
1-3) Dimension
[HMK-054]

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.7
[HMC-054]
61.5
67.5
58
64
Ø6
Ø2.7
Control board
[HMB-054]

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.8
[HMV-054]

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.9
1. Please press down the feed button.
Please make sure the remains which
the paper comes out.
2. Please insert the paper deeply as image (②),
then the autoloading will be starting.
You can see the paper cut, after it‟s feeding.
Please make sure if the paper direction is correct.
3. Please press the feed button to make sure if the paper
inserting is correct. (④)
2. Operation
2-1) Setting a paper : Auto Loading
[Paper direction]
②
④

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.10
1. Please print the paper out.
2. Please open up the head up lever as image (①).
3. Please insert the paper in, until the end of paper is
out of the paper guide. (③)
4. Please close up the head up lever. (④)
2-2) Setting a paper : Clamshell type
①
④
③

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.11
1. Please open up the head up lever.(①)
2. Please turn up the paper as image, and take out the
paper jamm. (②)
******************************
HMC-054 Control Board
Firmware :: R2.VerX .XX
Create : 20XX/XX/XX
******************************
Interface and Setting information
Interface : USB & RS-232C
Baud Rate : 19200
Data Bit : 8 Bit
Parity : None
Stop Bit : 1 or 2
Peripheral & Setting Information
USB Status : B
Auto Cutter :: BuiIt-in
2-3) Removing the paper jam
When you repair the cutter in the printer, before that, please firstly turn off the printer
2-3) Self-test
1. Please power on, once the feed button is being pressed down.
2. The following information will be printed.
Model
Firmware
Interface
Dip Switch
Sample printing
Please refer to the Dip switch info at 2-8).

①

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.12
2-4) HEX Dump
1. Please switch 7 *up at the dip switch, and power on. *up : on
It prints all data in hex character (16 antilogarithm), after [Hex Dump Mode] prints out.
2. It could know the printer status.
3. It will be useful for the application development.
It prints out if it receive Nine digits.
If it receives less than Nine digits, it will be printed if you press down feed button.
Control code ( 1F16 below) prints out as “.”.
8016 more prints out as “^”.
[Sample]
Hexadecimal ASCII
[HEX DUMP MODE]
41 42 43 44 45 46 47 47 49
30 31 32 33 34 35 36 37 38 0123 4 567
FF ^.i
1B
69
A B C D E F G H

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.13
2-5) Update (on Board)
By using flash memory ,it‟s able to simply update on the PC.
Please conduct the updates, after refering the following steps.
1) Please power off and on.
2) Please check if the PC is connected with printer.
* If use the USB Interface, the time will be saved to update.
3) Please conduct the given update program.
The update will be started after ERROR LED is off for 4 seconds.
* Please do not power off / switch off Dip switch until the update ends.
4) The update will be end, once the update complete appears on the screen.
※If the ERROR LED is appeared as on and off continuously, it could be error.
Please repeat these steps again, and check the interface cable, and the connections.
5) You can use the updated printer after update, it will be reset automatically then power off & on.

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.14
2-6) Memory Switch
Setting memory switch: Functions are set by internal non-volatile memory.
※For Setting, please use utility program for setting memory switch provided by us.
※Setting value will not be ereased even after power off, until next change.
Memory SW
Set Value
Description
SW1
Reserved
SW2
Reserved
SW3
Reserved
SW4
Standard
Code Page
For setting default value, select one of the code
page by country
SW5
Base Font
For setting default value in 2 bite code, select one
of Korean(24x24), Korean(16x16),
Japanese(24x24) or Chinese(24x24).
For setting default value in 1 bite code, select one
of ASCII(12x24) or ASCII(8x16,9x16).
SW6
Reserved
SW7
Reserved
SW8
Reserved
SW9
Reserved
SW10
Reserved
Code Page
Menu
Font Manu
Unuse
Atfer setting, please click
this button.

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.15
2) Verifying Memory Switch Modification
* After making a modification in memory switch, please verify the changes using self-test.
The printer will start the self-test process when you turn on the power while pressing down on
the FEED button, and press the FEED button one more time to indicate the details of memory
switch.
[Memory Switch information]
================================
Code Page = PC437(U.S)
2Byte Font = Korean(24x24)
1Byte Font = ASCII(12x24)
Mem1:FFh
Mem2:FFh,FFh
Mem3:FFh,FFh
Mem4:00h
Mem5:00h
Mem6:FFh
Mem7:FFh
Mem8:FFh
Mem9:FFh
Mem10:FFh
(Sample of verifying memory switch through self-test)

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.16
2-7) Rebooting Firmware
* If the firmware is damaged or cannot be booted due to the update error, you may use the
methods below to recover..
1) Check for the jumper which is beside Dip Switch on the bottom of printer
2) By using Pin Header(2.5mm), connect the JP2 pins together to short the circuit.
.
(Tool or Conductor Tools)
3) Connect the cable to printer, then turn on the power of printer.
4) Using the provided Booting Program and setting the interface port.
Then, Select board -> at91sam4e16-ek and click “Connect “
(RS-232 and USBport Possible only, However, the cable is only one to connect)
(If using the USB port, Save the time to set up)
5) After rebooting, Please remove JP2(Jumper Pins)
* If you skip this step, the printer would not reboot even after the firmware recovery because it
would delete the data.
Connect

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.17
6) Click the “ Icon “ in the Send file Name then atfer open the firmware file for Target model,
Then, Click “Send File Button”
* Notice : Do not revise the Parameter value.
7) Atfer the file is complete to transfer, Click “Yes “
①
②

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.18
8) Click “Excute” button, atfer checking for stting up “Boot from Flash(GPNVM1) in Scripts.
9) To re-operate printer, Tune off and on

Title
Revision.
Page
054 SERIES RELEASE2
R2.Ver2.0
P.19
2-8) Dip Switch
1)SW1 :
SW1
Realtime command Valid/Invalid
ON
DLE Command valid
OFF
DLE Command invalid
2)SW2,3 :
SW2
SW3
Baud Rate(BPS)
OFF
OFF
9600
ON
OFF
19200
ON
ON
38400
OFF
ON
115200
3)SW4 :
SW4
Jam Sensor
ON
Jam Sensor valid
OFF
Jam Sensor invalid
4)SW5,6 :
SW5
SW6
Parity
OFF
-
None
ON
OFF
Even
ON
ON
Odd
5)SW7 :
SW7
Print mode
ON
Hex Dump
OFF
Normal
6)SW8 :
SW8
Factory Mode
ON
Factory Mode
OFF
Standard Mode