HYCON HY16F3910 Series Instructions for use

© 2022 HYCON Technology Corp.
www.hycontek.com
APD-HY16F39IDE003-V02_EN
HY16F3910 Series
IDE Hardware User’s Manual
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page2
Table of Contents
1. PACKAGE CONTENTS............................................................................................................................ 4
2. SAFETY PRECAUTIONS ......................................................................................................................... 5
3. SOFTWARE INSTALLATION REQUIREMENTS..................................................................................... 6
3.1. IDE Software Installation Requirements ............................................................................................... 6
4. DESCRIPTION OF THE HARDWARE TOOL .......................................................................................... 7
4.1. Architecture desription .......................................................................................................................... 7
4.2. HY16F Mini Link Debug Tool Introduction............................................................................................. 7
4.3. Introduction to Target Board.................................................................................................................. 9
4.4. Target Board Circuit Diagram.............................................................................................................. 12
4.5. LCD Board Introduction ...................................................................................................................... 13
4.6. HY16F Mini Link Debug Tool and Target Board Hardware Connection Steps ................................... 16
5. HARDWARE CONNECTION INTRODUCTION ..................................................................................... 17
6. REVISIONS ............................................................................................................................................. 18
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page3
Attention:
1、HYCON Technology Corp. reserves the right to change the content of this datasheet
without further notice. For most up-to-date information, please constantly visit our
website: http://www.hycontek.com .
2、HYCON Technology Corp. is not responsible for problems caused by figures or
application circuits narrated herein whose related industrial properties belong to third
parties.
3、Specifications of any HYCON Technology Corp. products detailed or contained herein
stipulate the performance, characteristics, and functions of the specified products in the
independent state. We does not guarantee of the performance, characteristics, and
functions of the specified products as placed in the customer’s products or equipment.
Constant and sufficient verification and evaluation is highly advised.
4、Please note the operating conditions of input voltage, output voltage and load current
and ensure the IC internal power consumption does not exceed that of package
tolerance. HYCON Technology Corp. assumes no responsibility for equipment failures
that resulted from using products at values that exceed, even momentarily, rated values
listed in products specifications of HYCON products specified herein.
5、Notwithstanding this product has built-in ESD protection circuit, please do not exert
excessive static electricity to protection circuit.
6、Products specified or contained herein cannot be employed in applications which
require extremely high levels of reliability, such as device or equipment affecting the
human body, health/medical equipments, security systems, or any apparatus installed in
aircrafts and other vehicles.
7 、 Despite the fact that HYCON Technology Corp. endeavors to enhance product quality
as well as reliability in every possible way, failure or malfunction of semiconductor
products may happen. Hence, users are strongly recommended to comply with safety
design including redundancy and fire-precaution equipments to prevent any accidents
and fires that may follow.
8 、 Use of the information described herein for other purposes and/or reproduction or
copying without the permission of HYCON Technology Corp. is strictly prohibited .
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page4
1. Package Contents
HY16F3910-DK01 Hardware development kit includes HY16F3910-N088 Target Board
and HY16F Mini Link Debug Tool(refer to table 1-1).
Integrated Hardware development kit helps to develop MCU application program of
HY16F3910 Series. Program compiling, hardware debug, IC programming was
implemented through NB/PC end connection. This user’s manual mainly introduces the IDE
hardware development tool, the related hardware is equipped as shown below:
Model No. Part Name Description Quantity
HY16F3910-DK01
1.HY16F3910-IM01 HY16F3910-N088 Target Board 1
2.HY16000-CM04 HY16F Mini Link Debug Tool 1
3.HY10000-AM01 LCD Board
(3.0V, 4COM x 17SEG) 1
4.Cable line USB Type A to Mini B cable 1
5.EDM line 5pin to 5 pin (2.54mm pitch) 1
Table 1-1
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page5
2. Safety Precautions
Do not place heavy objects on the display panel, in order to avoid damage caused by
stress.
Place the application display boards at steady place, so as to avoid falling damage.
Do not use this product with the input voltage which is not meeting the electrical
specifications, , in order to avoid working abnormally or damage
Avoid application display boards being touched by liquid, dirt and avoid being exposed
to moisture during operation. This application should be kept in a dry environment, so
as not to affect the function and performance
Remove the power supply when not using it.
When following status occurred, please remove the power supply immediately, and
contact our engineer.
Power Supply line is worn or damaged.
Power source (battery) connected but no any light on while operating.
Component off.
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page6
3. Software Installation Requirements
3.1. IDE Software Installation Requirements
Minimum System Requirements of operating AndeSight RDS IDE:
(1) PC/NB hardware requirement:
IBM PC compatible X86 system CPU
4GB DDR Memory
8GB HD Hard Disk Drive Capacity
(2) Supported Products:
HY16F3910 Series
(3) Supported Hardware Model No.:
HY16F3910-DK01: HY16F3910 hardware development kit.
(4) Supported software version:
AndeSightV3.2.1RDS above
HYCON 32-bit MCU Device V0.34 above
(5) Supported Operating system:
Windows XP (32-Bit System), Windows 7(32/64-Bit System), Windows 8(32/64-Bit
System), Windows 10(32/64-Bit System).
(6) Apply the following interface modes:
USB Port with libusb-win32 device
HY16F Mini Link Debug Tool 's USB Port driver uses the Windows general USB
device driver.(Figure 3-1)
Figure 3-1
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page7
4. Description of the hardware tool
4.1. Architecture description
HY16F Mini Link Debug Tool(ICE) is a control device between the HY163910-N088 Target
Board and AndeSight RDS IDE software.
Program compiling, software debug, hardware debug, IC programming was implemented
through NB/PC end connection.
Figure 4-1
Note: EDM is Embedded Debug Module
4.2. HY16F Mini Link Debug Tool Introduction
HY16F Mini Link Debug Tool (model:HY16000-CM04) is universal for HY16F series
products (as shown in Figure 4-2), the following is the introduction of the HY16F Mini Link
Debug Tool:
EDM control
Port
USB Port
Power LED Error LED
Active LED
Figure 4-2
(1) Power LED
Function: Power LED (Green LED)
Description: When the USB Port is connected to a computer or an external 5V power
supply, the light indicates that the Control Box is powered.
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page8
(2) Active LED
Function: Active LED (Yellow LED)
Description: When entering Debug mode, the Active LED keeps flashing.
(3) Error LED
Function: Error LED (Red LED)
Description: When the USB Port is connected to a computer or an external 5V power
supply, but the EDM control port is not connected to Target Board, the
Error LED will light on.
(4) USB Port
Function: USB Port
Description: Mini B Cable connector
(5) EDM control Port
Function: EDM control communication interface port , used to connect with the EDM
interface of the Target Board to control the chip.
Description: The function is defined as follows
Name Description
RST RST Pin, connected to the RST pin of the HY16F3910.
VDD
VDD Pin, connected to the VDD5V pin of the HY16F3910.
Note: HY16F Mini Link Debug Tool fixed output 3.3V with 200mA
power supply.
ECK EDM Clock Pin, connected to the ECK pin of the HY16F3910.
EDIO EDM
Data Input / Output Pin, connected to the EDIO pin of the
HY16F3910.
VSS Ground Pin, connected to the VSS pin of the HY16F3910.
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page9
4.3. Introduction to Target Board
The Target Board (model: HY16F3910-IM01) is commonly used for HY16F3910 series
products (Figure 4-3) and demonstrate the function of HY16F3910.
The following describes the appearance and functions of the Target board:
J2
U1
J3
J5
J1
JP1
LOAD
CELL
Pin 1
Figure 4-3
(1) U1
Function: Target Board Chip, called HY16F3910 (Part No: HY16F3910-N088).
(2) J1
Function:SPIPWR Power Source Selection.
When J1’s pin1-2 are shorted together, the SPIPWR Powered by PWR.
Description:Pin are defined as follows
Name Pin Name
SPIPWR 1 2 PWR
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page10
(3) J2
Function: Target Board Chip’s LCD port.
Description: Pin are defined as follows
Name Pin Name
COM0 1 2 COM1
COM2 3 4 COM3
SEG0 5 6 SEG1
SEG2 7 8 SEG3
SEG4 9 10 SEG5
SEG6 11 12 SEG7
SEG8 13 14 SEG9
SEG10 15 16 SEG11
SEG12 17 18 SEG13
SEG14 19 20 SEG15
SEG16 21 22 SEG17
SEG18 23 24 SEG19
SEG20 25 26 SEG21
SEG22 27 28 SEG23
SEG24 29 30 SEG25
SEG26 31 32 SEG27
SEG28 33 34 SEG29
SEG30 35 36 SEG31
SEG32 37 38 SEG33
SEG34 39 40 SEG35
SEG36 41 42 SEG37
SEG38 43 44 SEG39
SEG40 45 46 SEG41
SEG42 47 48 SEG43
(4) J3
Function: Target Board Chip’s Current measurement.
It can be used to measure chip current by ammeter.
Description: Pin are defined as follows
Name Pin Name
VDD5V 1 2 PWR
Note: When J3 pin is not used to measurement, keep the J3 pin shorted together.
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page11
(5) J5
Function: Target Board Chip’s EDM Port and connected to the HY16F Mini Link Debug
Tool for Debug.
Description: Pin are defined as follows
Pin Name Description
1 RST1 RST Pin, connected to the RST pin of the HY16F Mini Link
Debug Tool.
2 PWR PWR Pin, connected to the VDD pin of the HY16F Mini Link
Debug Tool.
3 ECK1 ECK1 Pin,
connected to the ECK pin of the HY16F Mini Link
Debug Tool.
4 EDIO1 EDIO1 Pin, connected to the EDIO pin of the HY16F Mini
Link Debug Tool.
5 VSS VSS Pin, connected to the VSS pin of the HY16F Mini Link
Debug Tool.
(6) JP1
Function: Target Board Chip’s SPI Port.
When J1’s pin1-2 are shorted together, the SPIPWR Powered by PWR;
If PWR is 3V, then SPIPWR is 3V.
Description: Pin are defined as follows
Name Pin Name
SPIPWR 1 2 SPIPWR
MOSI 3 4 MOSI
SCK 5 6 SCK
MISO 7 8 MISO
CS 9 10 CS
VSS 11 12 VSS
(7) LOAD CELL
Function: Target Board Chip’s ADC Bridge Sensor Connector and it can measure
circuit. The ADC Bridge Sensor is composed of AIO0, AIO1, AIO2 and AIO3.
Description: Pin are defined as follows
Pin Name
1 S+
2 S-
3 E-
4 E+
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page12
4.4. Target Board Circuit Diagram
Note:
This Target Board circuit diagram is is placed in the Andes IDE software directory installed
below: " \Andestech\AndeSight_RDS_v321\doc\Hycon\ICESchematic\ “.
HY16F3910 Demo Board
V02A20016
PT1.7
26
PT2.3
1
PT2.2
2
PT2.1
3
PT2.0
4
VDD15
5
VLCD
6
VDD5V
7
VSS
8
VSSA
9
VDDA
10
AIO0
11
AIO1
12
SDRV1
13
AIO2
14
AIO3
15
SDRV2
16
PT3.7
17
PT3.6
18
PT3.5
19
PT3.4
20
PT3.3
21
PT3.2
22
RST
23
PT3.1
24
PT3.0
25
PT1.2
31
PT1.6
27
PT1.5
28
PT1.4
29
PT1.3
30
PT1.1
32
PT1.0
33
NC
34
PT10.7/SEG41
35
PT10.6/SEG40
36
PT10.5/SEG39
37
PT10.4/SEG38
38
PT10.3/SEG37
39
PT10.2/SEG36
40
PT10.1/SEG35
41
PT10.0/SEG34
42
PT9.7/SEG33
43
PT9.6/SEG32
44
PT9.5/SEG31 45
PT9.4/SEG30 46 PT9.3/SEG29 47 PT9.2/SEG28 48 PT9.1/SEG27 49 PT9.0/SEG26 50 PT8.7/SEG25 51 PT8.6/SEG24 52 PT8.5/SEG23 53 PT8.4/SEG22 54
PT8.3/SEG21 55
PT8.2/SEG20 56 PT8.1/SEG19 57 PT8.0/SEG18 58 PT7.7/SEG17 59 PT7.6/SEG16 60 PT7.5/SEG15 61 PT7.4/SEG14 62 PT7.3/SEG13 63 PT7.2/SEG12 64
PT7.1/SEG11 65
PT7.0/SEG10 66 PT6.7/SEG9 67
PT6.6/SEG8 68
PT6.5/SEG7 69
PT6.4/SEG6 70
PT6.3/SEG5 71
PT6.2/SEG4 72
PT6.1/SEG3 73
PT6.0/SEG2 74
PT13.7/SEG43/COM7 75
PT13.6/SEG42/COM6 76
PT13.5/SEG1/COM5 77
PT13.4/SEG0/COM4 78
PT13.3/COM3 79
PT13.2/COM2 80
PT13.1/COM1 81
PT13.0/COM0 82
NC 83
PT2.7 84
PT2.6 85
PT2.5 86
PT2.4 87
NC 88
U1 HY16F3910_QFN88
Y1 32768Hz
LS_XOUT LS_XIN
R1 10M
C1 C3
VSS
Keep crystal from other circuit
Y2 16MHz
HS_XIN
R2 1M
HS_XOUT
C2 C4
VSS
Keep crystal from other circuit
LS_XOUT
LS_XIN
HS_XIN
HS_XOUT
PT24
PT25
PT26
PT27
PT20 PT21 PT22 PT23
C12 10uF
VDD5V
VSS
C6 0.1uF
VDD15
VSS
VDD15 VDD5V
NC1
NC2
NC3
VSS VSSA VDDA
C15 10n
VSS
RST
R10 NC/4.7k
VDD5V
VSS
S1 RST
1
2
J3 Current
VDD5V
VSS
1 2 3 4 5 6 7 8 9 10 11 12
JP1 SPI
J1 SPIPWR
PWR
PWR
VSS
C8 1uF
VLCD
VSS
C10 0.1uF
VSSA
C9 1uF
VSSA
VDDA REFO
REFO
PT30
PT31
PT32 PT33 PT34 PT35 PT36 PT37
RST
RST
R14 0
EDIO
R13 1k
R12 1k
PWR
ECK
R17 0R
R15 0R
1
2 3 4 5
J5 EDM
RST1 PWR ECK1 EDIO1
VSS
PT20 PT21 PT22 PT23
EDIO
ECK
PT10
PT11
PT12
PT13
PT14
PT15
PT16
PT17
CS SCK MISO MOSI
C5 1nF
AIO2 AIO3
AIO0 AIO1 AIO2 AIO3 VLCD
C11 1nF
AIO0 AIO1
C13 1nF
VSS
C7 1nF
VSS
Near Chip
S3 KEY0 S2 KEY1
INT0 INT1 R11
100k R16 100k
PWR
INT0
INT1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
J2 Header 24X2
COM0 COM1 COM2 COM3 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 SEG34 SEG35 SEG36 SEG37 SEG38 SEG39 SEG40 SEG41 SEG42 SEG43
COM0
COM1
COM2
COM3
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31
SEG32
SEG33
SEG34
SEG35
SEG36
SEG37
SEG38
SEG39
SEG40
SEG41 SEG42
SEG43
PT130
PT131
PT132
PT133
PT134
PT135
PT136
PT137
PT60
PT61
PT62
PT63
PT64
PT65
PT66
PT67
PT70 PT71 PT72 PT73 PT74 PT75 PT76 PT77 PT80 PT81 PT82 PT83 PT84 PT85 PT86 PT87 PT90 PT91 PT92 PT93 PT94 PT95
PT96
PT97
PT100
PT101
PT102
PT103
PT104
PT105
PT106
PT107
SDRV1 SDRV2
Bridge Sensor Measure ment
R5 0R
C14 NC/0.1uF
AIO1 AIO0
AIO2
R7 0R
R6 0R
AIO3
+E
4
+S 1
-E 3
-S
2
1
LOADCELL_1
R8 0R
V+ V-
V- V+
R4 0R
SDRV1
R9 0R
SDRV2
CS SCK MISO MOSI
SEG0 SEG1
PWR
VSS
1 2 3 4
J4 Hea der 4
1 2 3 4
J6 Hea der 4
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page13
4.5. LCD Board Introduction
The LCD panel (model:HY10000-AM01) on HY16F3910-N088 Target Board is HYCON
self-owned mold, it’s symbol and pin diagram is shown in below graph.
It’s panel specification is as follows:
(1) Operating Voltage: 3.0V
(2) Visible Angle: 60 degree
(3) Operating Frequency: 60Hz
(4) Bias:1/3 bias
(5) Waveform:1/4 duty
(6) Pin: 90 degree
Top side of HY10000-AM01 Bottom side of HY10000-AM01
J1 pin assignment
J2 pin assignment
Pin No. 1 2 3 4 5 6 7 8 9 10 11
Pin Name COM0 COM1 COM2 COM3 SEG0 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6
Pin No. 12 13 14 15 16 17 18 19 20 21
Pin Name SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16
Pin Name COM0 COM2 SEG0 SEG2 SEG4 SEG6 SEG8 SEG10 SEG12 SEG14 SEG16
Pin No. 1 3 5 7 9 11 13 15 17 19 21
Pin No. 2 4 6 8 10 12 14 16 18 20 22
Pin Name COM1 COM3 SEG1 SEG3 SEG5 SEG7 SEG9 SEG11 SEG13 SEG15 -
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Techno ogy Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page14
HY10000-AM01: LCD Logi al Table
SEG0 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16
COM0 1A 1E 2A 2E 3A 3E 4A 4E 5A 5E 6A 6E S1 S5 S10 S9 S18
COM1 1B 1F 2B 2F 3B 3F 4B 4F 5B 5F 6B 6F S2 S6 S11 S14 S19
COM2 1C 1G 2C 2G 3C 3G 4C 4G 5C 5G 6C 6G S3 S7 S12 S15 S20
COM3 1D 1H 2D 2H 3D 3H 4D 4H 5D 5H 6D S17 S4 S8 S13 S16 S21
HY10000-AM01: LCD LCD Dimensions
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Techno ogy Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page15
HY10000-AM01: LCD COM/SEG Layout
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page16
4.6. HY16F Mini Link Debug Tool and Target Board Hardware Connection Steps
Step1: Make sure that Target Board’s J3 pin are shorted together.
Step2: Connect the HY16F Mini Link Debug Tool EDM control Port and Target Board’s
EDM Port with the 5-wire EDM line.
Step3: Use the USB Cable to connect to the HY16F Mini Link Debug Tool USB Port and
the computer's USB port (Power LED wi ight on; The LCD pane start counting).
Step4: After Step 1~3 (as shown in Figure 4-5), the hardware connection is completed.
Step2
J5
Step3
Power LED
LCD
Step1
Figure 4-5
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page17
5. Hardware Connection Introduction
For driver install, please refer to HY16F Series, IDE Software User’s Manual.
AICE USB driver program will install automatically when the software is installed.
For correct AICE connection status, libusb-win32 devices of AICE (which is HY16F Mini
Link Debug Tool ) will show up under PC device administrator.
EDM connection test:
(1) Connect the HY16F Mini Link Debug Tool to the Target Board .
(2) Open the AndeSight IDE software.(Please refer to installation HY16F series IDE
software installation steps)
(2.1) In the Target Manager: Local Targets window
(2.2) Select HY16F3910 by right-clicking(Select Connect Target via AICE)
(2.3) Successful connection appears HY16F3910 ICE-ICE:9904
(2.4-2.5) From the Console window, can see the version information of the Mini
Link:Andes AICE-MINI v1.0.1
1.
2.
3.
4.
5.
.

HY16F3910
IDE Hardware User’s Manual
© 2022 HYCON Technology Corp
www.hycontek.com
APD-HY16F39IDE003-V02_EN
page18
6. Revisions
The following describes the major changes made to the document, excluding the font and
punctuation changes.
Version Page Date Revision Summary
V02 ALL 2022/05/17 First edition
.