HYCON HY17S68 Series Instructions for use

© 2020 HYCON Technology Corp.
www.hycontek.com
APD-HY17PIDE006-V01_EN
HY17S68 Series
HY17S68-DK02 IDE
Hardware User’s Manual
.

HY17S68 Series
HY17S68-DK02 IDE
Hardware User’s Manual
© 2020 HYCON Technology Corp
www.hycontek.com
APD-HY17PIDE006-V01_EN
page2
Table of Contents
1. PACKAGE CONTENTS............................................................................................................................4
2. SAFETY PRECAUTIONS.........................................................................................................................5
3. SOFTWARE INSTALLATION REQUIREMENTS.....................................................................................6
3.1. IDE Software Installation Requirements...............................................................................................6
4. DESCRIPTION OF THE HARDWARE TOOL ..........................................................................................7
4.1. Schematic architecture description.......................................................................................................7
4.2. Description of control box .....................................................................................................................7
4.3. Description of In-Circuit Emulator(ICE) Board......................................................................................8
4.4. ICE board circuit diagram ...................................................................................................................10
4.5. Control box and ICE board hardware connection steps..................................................................... 11
5. REVISION RECORD...............................................................................................................................12
.

HY17S68 Series
HY17S68-DK02 IDE
Hardware User’s Manual
© 2020 HYCON Technology Corp
www.hycontek.com
APD-HY17PIDE006-V01_EN
page3
Attention:
1、HYCON Technology Corp. reserves the right to change the content of this datasheet
without further notice. For most up-to-date information, please constantly visit our
website: http://www.hycontek.com .
2、HYCON Technology Corp. is not responsible for problems caused by figures or
application circuits narrated herein whose related industrial properties belong to third
parties.
3、Specifications of any HYCON Technology Corp. products detailed or contained herein
stipulate the performance, characteristics, and functions of the specified products in the
independent state. We does not guarantee of the performance, characteristics, and
functions of the specified products as placed in the customer’s products or equipment.
Constant and sufficient verification and evaluation is highly advised.
4、Please note the operating conditions of input voltage, output voltage and load current
and ensure the IC internal power consumption does not exceed that of package
tolerance. HYCON Technology Corp. assumes no responsibility for equipment failures
that resulted from using products at values that exceed, even momentarily, rated values
listed in products specifications of HYCON products specified herein.
5、Notwithstanding this product has built-in ESD protection circuit, please do not exert
excessive static electricity to protection circuit.
6、Products specified or contained herein cannot be employed in applications which
require extremely high levels of reliability, such as device or equipment affecting the
human body, health/medical equipments, security systems, or any apparatus installed in
aircrafts and other vehicles.
7、Despite the fact that HYCON Technology Corp. endeavors to enhance product quality
as well as reliability in every possible way, failure or malfunction of semiconductor
products may happen. Hence, users are strongly recommended to comply with safety
design including redundancy and fire-precaution equipments to prevent any accidents
and fires that may follow.
8、Use of the information described herein for other purposes and/or reproduction or
copying without the permission of HYCON Technology Corp. is strictly prohibited.
.

HY17S68 Series
HY17S68-DK02 IDE
Hardware User’s Manual
© 2020 HYCON Technology Corp
www.hycontek.com
APD-HY17PIDE006-V01_EN
page4
1. Package Contents
HY17S68-DK02 is an integrated hardware development kit, including ICE
(In-Circuit Emulator) Board, Control Box, LCD Board and USB Cable. Integrated hardware
development kit helps to develop MCU application program of HY17P6x Series. Through
the NB/PC end connection for program compilation and debugging functions, the relevant
hardware equipment is as follows:
Model No.
Part Name
Description
Quantity
HY17S68-DK02
1. HY17S68-IM02
HY17S68-L216 ICE Board
1
2. HY17000-CM01
HY17S Control Box
1
3. HY10000-AM01
LCD Board
1
4. Cable line
USB Type A to Mini. B Cable
1
5. Interface line
6pin/2.54 (2.54mm pitch)
1
Table 1-1
.

HY17S68 Series
HY17S68-DK02 IDE
Hardware User’s Manual
© 2020 HYCON Technology Corp
www.hycontek.com
APD-HY17PIDE006-V01_EN
page5
2. Safety Precautions
Do not place heavy objects on the display panel, in order to avoid damage caused by
stress.
Place the application display boards at steady place, so as to avoid falling damage.
Do not use this product with the input voltage which is not meeting the electrical
specifications, in order to avoid working abnormally or damage.
Avoid application display boards being touched by liquid, dirt and avoid being exposed
to moisture during operation. This application should be kept in a dry environment, so
as not to affect the function and performance.
Remove the power supply when not using it.
When following status occurred, please remove the power supply immediately, and
contact our engineer.
Power Supply line is worn or damaged.
Power source (battery) connected but no any light on while operating.
Component off.
.

HY17S68 Series
HY17S68-DK02 IDE
Hardware User’s Manual
© 2020 HYCON Technology Corp
www.hycontek.com
APD-HY17PIDE006-V01_EN
page6
3. Software Installation Requirements
3.1. IDE Software Installation Requirements
Minimum System Requirements of operating HY17S68 IDE hardware development tool:
(1) PC/NB hardware requirement
IBM PC compatible X86 system CPU
512 MB Memory (1GB recommended)
1GB Hard disk
(2) Supported product model
HY17P60 and HY17P68 series products
(3) Hardware support models
HY17S68-DK02: HY17S68 IDE hardware development tool
(HY17000-CM01 supports firmware version above W15P02.0)
(4) Software supported version
HY17P IDE V1.2 version above：HY17P Series Assembly Language IDE software
H08 CIDE V1.2 version above：HYCON 8-bit MCU C Language IDE software
(5) Operating system requirements
Windows XP, Windows Vista, Windows 7, Windows 8, Windows 10
(6) Applicable interface mode
USB Port with HID-compliant device
HY17S68-DK02's USB Port driver uses the Windows standard HID driver
(Figure 3-1), so user can use it without installing a separate driver.
Figure 3-1
.

HY17S68 Series
HY17S68-DK02 IDE
Hardware User’s Manual
© 2020 HYCON Technology Corp
www.hycontek.com
APD-HY17PIDE006-V01_EN
page7
4. Description of the hardware tool
4.1. Schematic architecture description
HY17000-CM01 (control box) is the connecting device between HY17S68-IM02 ICE
Board and HY17P Series IDE software.
Connect with HY17S68-IM02 ICE board through Interface line (6Pin/2.54mm).
Connect with HY17P Series IDE software through USB line, the connection diagram is
as follows:
Figure 4-1
4.2. Description of control box
The control box (model: HY17000-CM01) is universal for HY17P series products (as shown
in Figure 4-2). The following is the introduction of the control box:
HY17P
HY17000-CM01
Power LED
USB Port
Debug Port
Figure 4-2
(1) Power LED
Function：POWER LED
Item
Name
Description
L1
Power LED
Green light, when the USB Port is connected to a computer
or a 5V power supply through a USB cable, when the
green light is on, it means that the control box is normally
powered.
.

HY17S68 Series
HY17S68-DK02 IDE
Hardware User’s Manual
© 2020 HYCON Technology Corp
www.hycontek.com
APD-HY17PIDE006-V01_EN
page8
(2) Debug Port
Function: IDE communication interface port, used to connect with the Debug interface
of the ICE Board to control the chip.
The function is defined as follows:
Item
Name
Description
1
VSS
Power ground
2
SCK
SCK Pin of Control Box and ICE board
3
VDD
Power output 4.5V
4
CS
CS Pin of Control Box and ICE board
5
SDI
SDI Pin of Control Box and ICE board
6
SDO
SDO Pin of Control Box and ICE board
(3) USB Port
Function：USB Port
Description: Mini B Cable connector
4.3. Description of In-Circuit Emulator(ICE) Board
The ICE board (model: HY17S68-IM02) is commonly used for HY17P6x series
products (see Figure 4-3). This ICE board is mainly used for IDE hardware tools, which can
be used to emulate chips and develop debugging. The following describes the appearance
and functions of the ICE board:
Figure 4-3
(1) Buzzer Output
Function: can make the buzzer sound
(2) J1: ICE Connecter
.

HY17S68 Series
HY17S68-DK02 IDE
Hardware User’s Manual
© 2020 HYCON Technology Corp
www.hycontek.com
APD-HY17PIDE006-V01_EN
page9
Function: connect with the control box (HY17000-CM01) to emulate the operation of
the chip.
(3) D1: Power LED
Function: Connect to the control box (HY17000-CM01), when power is supplied, D1 on
the ICE board will be on constantly
(4) LCD display(4COM*17SEG)
Function: Mainly control the use of LCD display.
(5) Reset Key
Function: Reset ICE to use.
(6) J3:VDD Jumper
Function: Provide HY17S68 power supply (4.5V)
(7) IC: HY17S68
Function: Emulation chip, used to emulate the use of HY17P6x series chips
(8) VSS Test point
Function: Use for grounding test
.

HY17S68 Series
HY17S68-DK02 IDE
Hardware User’s Manual
© 2020 HYCON Technology Corp
www.hycontek.com
APD-HY17PIDE006-V01_EN
page10
4.4. ICE board circuit diagram
1 1
2 2
3 3
4 4
5 5
6 6
D D
C C
B B
A A
Title
Number RevisionSize
C
Date: 2020/7/22 Sheet of
File: D:\PCB\..\A20014 V02.schdoc Drawn By:
HY17S68-IM02: HY17S68-L216_ICE Board
V02A20014
_VCC_ram
_VSS_ram
_SDI
_SDO
_SCK _SCS
R1
47K
R2
47K
R3
47K
VDD_bat
12 34 56 78 910 1112
J1
ICE
_SDI
_SDO
_SCK
_SCS
_VCC_ram
_VSS_ram
_ADR14
_ADR11 _ADR13 _ADR10
_ADR9 _ADR8
_DA7 _DA6 _DA5 _DA4 _DA3
_RD
_WE
VDD_bat
Program/SBM Memory
A5
5A6 4A7 3A8 25
A9 24
A10 21 A11 23
A12
2A13 26
A14
1
I/O0
11 I/O1 12 I/O2 13 I/O3 15
I/O4 16 I/O5 17 I/O6 18 I/O7 19
CE 20
A0
10
OE 22
A1
9A2 8A3 7A4 6
WE 27
GND
14
VCC 28
U1
62256
_VSS_ram
_ADR12
_ADR7 _ADR6 _ADR5 _ADR4 _ADR3 _ADR2 _ADR1 _ADR0
_DA2 _DA1 _DA0
_VSS_ram
* ICE Memory NET
VDD_bat
_CS
C1
0.1uF
VSS
28 PB0 29 PB1 30 PB2 31 PB3 32
PB5
34 PB6 35 PB7 36
OP1O
39 OP1N 40 RLU 41
RLD
45 PA0 46 PA1 47 PA2 48 PA3 49 PA4 50 PA5 51 PA6 52
PA7
57 PA8
58
FTP
74 FTN
75 AGND
76 REFO
77 VDDA
78 RST/VPP
79 VGG
80 CA
81 CB
82 VDD
83 VLCD
84 COM0/PSCK
85 COM1/PSDI
86 COM2/PSDO
87 COM3
88 SEG2/PT6.4
89 SEG3/PT6.5
90
SEG4/PT6.6
103 SEG5/PT6.7
104 SEG6/PT7.0
105 SEG7/PT7.1
106
SEG8/PT7.2 111 SEG9/PT7.3 112
SEG10/PT7.4 113 SEG11/PT7.5 114 SEG12/PT7.6 115 SEG13/PT7.7 116 SEG14/PT8.0 117
PB4
33
ICE_ADR13
25 ICE_ADR14 26
ICE_ADR10
22 ICE_ADR11 23 ICE_ADR12 24
ICE_ADR9
21
ICE_ADR6
18 ICE_ADR7 19 ICE_ADR8 20
ICE_DA5
4ICE_DA6 5ICE_DA7 6
ICE_ADR0
9ICE_ADR1
10
ICE_ADR2
14 ICE_ADR3 15 ICE_ADR4 16 ICE_ADR5 17
ICE_CS
7ICE_CS0 8
ICE_DA4
3
NC2
11 NC3 12 NC4 13
NC8
44 NC6 42 NC7 43
VSS_ICE
27
NC10
54 NC9 53
NC12
56 NC11
55
NC14
62 NC13
61
NC16
64 NC15
63
NC18
66 NC17
65
NC20
68 NC19
67
NC22
70 NC21
69
NC24
72 NC23
71
NC37
107 NC38
108
PB8
37 PB9 38
PA9
59 PA10
60
PA11
73
NC39 109 NC40 110
SEG15/PT8.1 122 SEG16/PT8.2 123 SEG17/PT8.3 124 SEG18/PT8.4 125 SEG19/PT8.5 126 SEG20/PT8.6 127 SEG21/PT8.7 128 SEG22/PT9.0 129 SEG23/PT9.1 130 SEG24/PT9.2 131 SEG25/PT9.3 132 SEG26/PT9.4 133 SEG27/PT9.5 134 SEG28/PT9.6 135 SEG29/PT9.7 136
SEG30/PT10.0 137 SEG31/PT10.1 138 SEG32/PT10.2 139
SEG38/PT11.0 145
SEG39/PT11.1 146
SEG40/PT11.2 147
SEG41/PT11.3 148
PT1.0/INT1.0/SDI 149
NC45 150 NC46 151
NC47 152
PT1.2/INT1.2/LVDIN 154
PT1.3/INT1.3/RC 155
PT1.4/INT1.4/TX 156
PT1.5/INT1.5/SDO/TBI1 157
PT1.6/INT1.6/SCK 158
PT1.7/INT1.7/BZ 159
NC51 160
PT1.1/INT1.1/SCE/TBI0 153
PT2.1/XTI/INT2.1 165
PT2.2/INT2.2/SCL 166
PT2.3/INT2.3/SDA 167
PT2.4/INT2.4 168
PT2.5/INT2.5 179
PT2.6/INT2.6 180
PT2.7/INT2.7/TBI2 181
PT3.0 182
PT3.1 183
PT3.2 184
PT3.3 185
PT3.5/PWM1 187
PT3.6/CNT 188
PT3.7/CMP 189
PT4.0 190
PT4.1 191
PT4.2 192
PT3.4/PWM0 186
PT4.3 193
PT4.4 194
ICE_VCC 195
ICE_SDI 198
ICE_SDO 197
ICE_SCK 199
ICE_RD 200
ICE_WE 196
ICE_DA0 211
ICE_DA1 212
ICE_DA2 213
ICE_DA3 214
SEG33/PT10.3 140 SEG34/PT10.4 141 SEG35/PT10.5 142 SEG36/PT10.6 143
SEG37/PT10.7 144
NC0
1NC1 2
NC72 215
NC73 216
NC25
91 NC26
92 NC27
93 NC28
94 NC29
95 NC30
96 NC31
97 NC32
98 NC33
99 NC34
100 NC35
101 NC36
102
NC41 118 NC42 119 NC43 120 NC44 121 NC48 161 NC49 162
NC50 163
PT2.0/XTO/INT2.0 164
NC52 169
NC53 170
NC54 171
NC55 172
NC56 173
NC57 174
NC58 175
NC59 176
NC60 177
NC61 178
NC62 201
NC63 202
NC64 203
NC65 204
NC66 205
NC67 206
NC68 207
NC69 208
NC70 209
NC71 210
U2
HY17S68_L216
_ADR14 _ADR12
_ADR7 _ADR6 _ADR5 _ADR4 _ADR3 _ADR2 _ADR9 _ADR8
_ADR10 _ADR11 _ADR13
_DA7 _DA6 _DA5 _DA4
_WE
_RD
_DA3
_DA2
_DA1
_DA0
_ADR1 _ADR0
_SCK
_SDI
_SDO
VSS
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44
J4
LCD
COM0 COM1 COM2 COM3
SEG
2SEG
3
SEG
4SEG
5
SEG
6SEG
7
SEG
8SEG
9
SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 SEG34 SEG35 SEG36 SEG37 SEG38 SEG39 SEG40 SEG41
VDD_bat
VDD
1
2
J3
Current test
SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32
SEG
8
SEG
9
SEG10 SEG34 SEG36 SEG38 SEG40 SEG35 SEG37 SEG39 SEG41 SEG33
COM0
COM1
COM2
COM3
SEG
2
SEG
3
SEG
4
SEG
5
SEG
6
SEG
7
SC
K
SDI
SDA
SCL
PSDO
PSDI
PSC
K
PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PB8 PB9
PA0 PA1 PA2 PA3 PA4 PA5 PA6
PA7
PA8
PA9
PA10
RC
TX
SDO
C5
0.1uF
R8
NC/100k
C12
0.47uF
VSS
SW1
RS
T
VDD
RS
T
VLCD
VGG
RS
T
REF
O
FTN
FTP
VDDA
AGND
VDD
VPP
C6
1uF
C7
1uF C8
1uF
VSSA
VSS
VSSVSS
C11
1uF
C10
1uF
C9
0.1uF
AGND ACOM
VSSA
C4
27nF
PA11
PT10 PT11 PT12 PT13 PT14 PT15 PT16 PT17
PT20
PT21
PT22
PT23
PT24
PT25
PT26
PT27
PT30
PT31
PT32
PT33
BUZZER
1
NC/BUZZER
VSS
XOUT
XIN
LVDIN
CS
PT34
PT35
PT36
PT37
PT40
PT41
PT42
PT43
PT44
OP1O
OP1N
VDD_bat
_CS
_SCS
R6 0R
VSSA
OP1N
R9
NC
R7
NC
OP1O
Internal OPA1
ACOM
RLU
RLD
CA
CB
R5 0R
_VCC_ram
_VSS_ram
VSSA
PT17
VSS
Y1
NC/4.9152MHz
R4
NC/1M
C2
NC/15pF C3
NC/15pF
XOUTXIN
PA7 PA8 PA9
PA10
VLCD
VGG
RST
REFO
FTN
FTP
VDDA
AGND
VDD PA11
CA
CB
PT10 PT11 PT12 PT13 PT14 PT15 PT16 PT17 PT20 PT21 PT22 PT23 PT24 PT25 PT26 PT27
PT30 PT31 PT32 PT33 PT34 PT35 PT36 PT37 PT40 PT41 PT42 PT43 PT44 PB0
PB1 PB2 PB3 PB4 PB5 PB6 PB7 PB8 PB9
OP1O
OP1N
RLU
VS
S
PA0 PA1 PA2 PA3 PA4 PA5 PA6
RLD
VSS HY17S68
LQFP216
* ICE Debug Port
* Current Test Port * Buzzer Output Option * Power In LED
_VCC_ram
_VSS_ram R10
270K
D1
Green 1
2 3 4
JP1
VSS
VSS
Figure 4-4
Note：The ICE board circuit diagram is placed in the IDE software folder,
"A20014 V02_HY17S68-IM02_HY17S68-L216 ICE Board.pdf"
The Assembly IDE folder path is: "HYCON\HY17P IDE\ICESchematic"
The H08 CIDE folder path is: "HYCON\H08 CIDE\ICESchematic\HY17P"
.

HY17S68 Series
HY17S68-DK02 IDE
Hardware User’s Manual
© 2020 HYCON Technology Corp
www.hycontek.com
APD-HY17PIDE006-V01_EN
page11
4.5. Control box and ICE board hardware connection steps
(1) Confirm that J3 (VDD Jumper) of the ICE board is short-circuited together.
(2) The Interface lines are respectively connected to the Debug port of the control box
and the ICE Connector (J1) of the ICE board.
(3) Use USB Cable to connect to the USB Port of the control box and the USB Port of
the computer (the Power LED will be on at this time).
(4) After Step1~3 (as shown in Figure 4-5), it means that the hardware of the control
box and the ICE board are properly connected.
Figure 4-5
.

HY17S68 Series
HY17S68-DK02 IDE
Hardware User’s Manual
© 2020 HYCON Technology Corp
www.hycontek.com
APD-HY17PIDE006-V01_EN
page12
5. Revision Record
Version
Page
Date
Summary
V01
All
2020/07/30
First version
.