HydroHoist HydroPort EPIC User manual

1

1035264RevA

2

1035264RevA
AtHydroHoist;wetakeprideinbringingthemostadvanced,easiesttouse,andlowestmaintenanceboatlisys-
temstothemarket.Installaonoftheliissimpleduetoitslightweightdesignandeaseofoperaon.
Thefollowingpagescontainstep-by-stepinstruconsoftheinstallaonandoperaonprocesses.
TheHydroPortEPIC™plaormtakes4 man‐hours (2people/2hourseach/4hourstotal)toassembleonaverage.
Reviewallparts,hardware,andrequiredtoolsbeforebeginningassembly.Don’tforget:safetyfirst.
Ifyouhavequesons,contacttheTechnicalSupportTeamat1-800-825-3379.

Legend:
Requirescarefulconsideraon
WARNING:couldcauseharmordamagetotheli,vessel,anduser
INTRODUCTION
It is STRONGLY recommended that the installer read the manual before aempng an installaon. 
Please Note: The mounng hardware for the HydroPort EPIC is the same as the HP Extreme model.
Within this manual, you will see the model HP Extreme part referenced when assembling the HP Epic.

3

1035264RevA

PRE‐INSTALLATION CONSIDERATIONS
ThefollowingdeterminaonsmustbemadebeforeinstallingtheHydroPortEPIC:
 LocaonofHydroPort Assembly(remoteoron-site)
 Methodoftransportfromassemblytolaunchsite
 Equipmentrequiredtosafelybuild,transport,andlaunchtheHydroPort
 Contactpointsbetweenwheelsandthehull(considerhullchines)
Otheritemstoconsider:
 Isthedockbuiltsoundenoughtosupportmountaporttothefaceboard?
 HowwillyoutransporttheHydroPortfromthelaunchsitetotheinstalllocaon?
 VerifythelocaonyouplantoinstalltheHydroPortwillaccommodatetheoverallsizeoftheHydroPort.See
Chart 1.
 SeeChart 2 foralistoftherequiredtools.
 SeeChart3foralltorquerequirements.
All references to the LEFT or RIGHT are considered to be facing forward, as if driving the person‐
al watercraonto the HydroPort plaorm.
 LEFT is port side
 RIGHT is starboard side
 Parts are occasionally described as LEFT or RIGHT to idenfy their opposing construcon, not
locaon on the HydroPort.
Working through these consideraons is the first step in a successful build.
 No alteraons or modificaons may be made to HydroHoist® equipment without the express
wrien consent of HydroHoist®. It is the obligaon of the End User to inform all equipment opera‐
tors of the above condions. 
 It is the responsibility of the End User to ensure that:
 The HydroPort EPIC is operated in a safe manner
 Regular inspecon is performed on the HydroPort EPIC components
 Customer and user reads and understands all safety and warning labels




4

1035264RevA
Chart 1: General Specificaon of the HydroPort EPIC
 Chart2:RequiredTools
1/2”DriveRatchet
(minimum9”handlelengthforleverage)DriPinorotherholealigningtool
ElectricDrill/Impact5/32HexKey
1/2”DrillBitJ-HookConnecngKitTool(4154029)Note:only
neededifconnecngtoasecondHydroPort
3/8”DrillBitLargeHammer(3or4lb.shophammerisbest)
3/4”DeepWellSocketKnifeortoolforcung
9/16”DeepWellSocketMeasuringTape
3/4”Open-endorCombinaonWrenches(2)15/16”Open-endorCombinaonWrenches
9/16”Open-endorCombinaonWrenches15/16”DeepWellSocket
#2PhillipsScrewdriver15/16Sock&wrenchregardlessofdockbracket

BOLT SIZE FOOT POUNDS OF TORQUE
1/4-205FT.LBS.
5/16-189FT.LBS.
3/8-1616FT.LBS.
7/16-1426FT.LBS.
1/2-1335FT.LBS.
9/16-1247FT.LBS.
5/8-1176FT.LBS.
Chart 3: Torque Specificaons
HYDROPORT EPIC DIMENSIONS
ALL DIMENSIONS IN INCHES
WIDTH LENGTH HEIGHT WEIGHT
70 160-5/8 17 430 LBS

5

1035264RevA
Chart 4: PARTS LIST—EPIC
EPIC HYDROPORT
Part Description Expected Quantity
HPT-02-0008 BODY—HP EPIC, HH BLUE (BODY ONLY) 1
HPRT-07-0009 AXLE-HP EPIC 12
4154004 5 X 2 WHEEL, HP EPIC 12
HDW-02-0001 SPACER-WHEEL-HP EPIC 34
4154006 AXLE RETAINER, HP EPIC 24
4154008 BOW STOP-HP EPIC 1
4154023 SCREW—1/4-20 X 2”-LG Ø TRUSS HD HPE 4
300124 INSERT— HEX—1/4-20 X .72 12
4154009 CAP PLUG-MOORING-HP EPIC 6
4150008 SCREW—1/4IN.—20 X .75 316 SS PAN HEAD 6
400167 SPINWELD #81 BLUE 6
FIXED DOCK MOORING KIT 4154032
Part Description Expected Quantity
4154044 BRACKET-FIXED DOCK MOORING - REINFORECED 2
3151200 BACK PLATE - REINFORCEMENT - GALV 2
4154126 KIT - BAG HP EXTREME HARDWARE FIXED FEMALE MOORING PLUG 1
4154084 MOORING PLUG 5/8—II FEMALE BRASS PLUG HP EXTREME 2
4154031 KIT—MOORING KIT HPE 1
FLOATING DOCK MOORING KIT 4154025
Part Description Expected Quantity
4154025 KIT - HARDWARE HP EPIC FLOATING DOCK 1
4154143 HARDWARE KIT- HP EPIC FLOATING 5/8" GALV FEMALE MOORING PLUG 1
4154084 MOORING PLUG 5/8 II FEMALE BRASS PLUG HP EXTREME 2
4154080 FLOATING MOORING, HP EPIC WELDED CORNERS AND STRESS RELIEVE 2
4154047 PLATE - MOORING HINGE HP EXTREME FLOATING MOORING 2
2000000 LITERATURE - REGISTRATION CARD 1
Chart 5: PARTS LIST—HYDROPORT EPIC FIXED DOCK BRACKET
Chart 6: PARTS LIST—HYDROPORT EPIC FLOATING DOCK BRACKET

6

1035264RevA
Chart 7: PARTS LIST—HYDROPORT EPIC CONNECTING KIT
KIT—CONNECTING FOR HP EXTREME OR EPIC
Part Description Expected Quantity
4154028 KIT - CONNECTING HP EXTREME 1
4154015 BOTTOM PLUG CONNNECTION THREADED, HP EXTREME 2
4154016 TOP PLUG THREADED, HP EXTREME 2
2099610 BOX - HP2 (16" X 8" X 6 1/2") DRY BIX WAXED 1
4154033 KIT BAG - HP EXTREME CONNECTION HARDWARE 1
HDW-06-0002 SPACER TUBE— 1/2” DIA. ALUMINUM PIPE 2
HPT-13-0011 CARD—DIRECTIONS TO ONLINE HYDROPORT MANUAL 1

7

1035264RevA
STEP 1: BOW STOP INSTALLATION
1.InserttheBowStopintotheEPICbody.
2.InsertScrews4154023throughtheBowStopinthefourlocaons,shownbelow.
3.Tightenthefourscrews.
Part # Hardware Required Quanty
4154023SCREW—1/4-20X2”-LGØTRUSSHD 4
Part # Parts Required (Per Port) Quanty
BODYBODY-EPIC(BODYONLY)1
4154008BOWSTOP-HPEPIC1
4154023
BOWSTOP
FULLYASSEMBLED

8

1035264RevA
STEP 2: WHEEL ASSEMBLY
1.SlidetheAxleRetainer(4154006)ononeendoftheAxleHPT-07-0009.
2.SlideoneSpacer(HDW-02-0001)ontotheAxle(HPT-07-0009)andthroughtheWheel(4154004).
3.AddtwomoreSpacers(HDW-02-0001)ontotheAxle(HPT-07-0009).
4.InsertAxleRetainer(4154006)ontotheAxle(HPT-07-0009)tocompleteassembly.
Part # Parts Required (Per Port) Quanty
41540045X2WHEEL-HPEPIC12
HPT-07-0009AXLE-HPEPIC12
4154006AXLERETAINER,HPEPIC24
Part # Hardware Required Quanty
HDW-02-0001SPACER-WHEEL-HPEPIC36

4154006(X2)4154004
HPT‐07‐0009HDW‐02‐0001(X3)
4154006(X2)4154004
HPT‐07‐0009
HDW‐02‐0001(x2)
Port Wheel Assembly ( Standard install 4 sets)
Port Rear Entry Wheel Assembly ( Standard install 2 sets)

9

1035264RevA
STEP 2: WHEEL PLACEMENT— Port Entry
1.Snapthewheelassembly(ACC-01-0002)intotheEPICbody(PHT-01-0008)axlecavies.ManyAxlelocaons
areprovidedtocustomfittheEPICbodytoyourcra.Thewheelplacementisshippedwithallwheelassem-
bliesplacedontheinsidetrack.

Duetothedifferencesbetweeneachmodelandmanufactureofhullsitmaytakesometrialanderrorto
determinelocaonofeachwheelsetforproperloadingofyourvessel.Addionalaxlesetsareavailable
forpurchaseifmorewheelsarerequired.
Thesingleaxilspacersshouldbeontheeithersideofthewheeltoavoidwheelcomingincontactwith
theport.

10

1035264RevA
STEP 3: PLUG MOORING CAVITIES
1.PlacetheCapPlugintothemooringcavityintheEPICbody.
2.InsertscrewsthroughtheCapPlugintothethreadedinsertintheEPICbody.
3.TightenScrewsunlsnug.
IMPORTANT: DO NOT OVERTIGHTEN THE SCREWS. THE SCREWS ONLY NEED TO BE TIGHTENED ENOUGH TO
RETAIN THE CAP PLUG.
Part # Parts Required (Per Port) Quanty
BODYBODY-EPIC(BODYONLY)1
4154009CAPPLUG-MOORING-HPEXTREME6
Part # Hardware Required Quanty
4150008SCREW-1/4IN.-20X.75316SSPANHEAD6
PLUGASSEMBLYCOMPLETE
4150008(X6)
HPT‐02‐0008(X1)
4154009 (X6)

11

1035264RevA
STEP 4: ATTACH TO THE DOCK ‐FLOATING DOCK APPLICATION
1.PlacetheLockWasherandtheWasheronbothBolts.(4151927,2090707,2090212)
2.InserttheMooringPlug(4154084)intothemooringcavityintheEPIC.
3.HooktheMooringBracket(4154080)intothemooringcavityontheundersideoftheEPICbody.
3.PivotthebracketuptotheEPICbody.Mayneedtouseahammertotapthebracketintoplace.
4.InserttheBoltandWashers(see1.)intotheMooringPlugandghtenunltheBracketissnugagainsttheEPIC
body.
Part # Hardware Required Quanty
4151927BOLT-5/8-11X1.52
2090707LOCKWASHER—5/8GALV2
2090212WASHER-FLT-5/8”GALV2
4154143HPEXTREMEHARDWAREBAGFLOAT-
ING 1
Part # Parts Required (Per Port) Quanty
4154025KIT—HARDWAREHPEXTREMEFLOATINGDOCK1
4154084MOORINGPLUG5/8-11FEMALEBRASSPLUGHPEPIC2
4154080FLOATINGMOORING,HPEXTREMEWELDEDCORNERSANDSTRESS
RELIEVE2
IMPORTANT: Do not exceed the maximum torque required of 72 ‐lbs.
ASSEMBLYCOMPLETE
BOLTASSEMBLY
COMPLETE
4151927(X2)
2090707(X2)
2090212(X2)
4154080(X2)
4154084(X2)
REMINDER: TIGHT IS TIGHT AND TOO TIGHT IS BROKEN!

12

1035264RevA

STEP 5: ATTACH TO THE FLOATING DOCK
1.Drillfour3/8”holesintodockfaceandaachtheExtendedHingeMooringPlate(4154047).SeeBelow.
2.WhenusingtheHDDockBracket(5049000)withtheMooringHingePlate,holesonlyneedtobedrilledwhen
usingthethru-boltmethodofdockbracketconnecon.

IT IS CRITICAL TO VERIFY THE DOCK IS BUILD STRONG ENOUGH TO ATTTACH THE PORT TOO. ADDITIONAL REINFORCE-
MENT MAY BE NECESSARY IN ROUGH WATER.
Part # Hardware Required Quanty
4151927BOLT-5/8-11X1.52
2090707LOCKWASHER-5/8GALV4
2090212WASHER-FLT-5/8”GALV2
4154048BOLT—5/8-1161/2IN.GALV2
2090111NUT-HEX5/8-11GALV4
2090507BOLT-HEX1/2-13IN.GALV4
2090705WASHER-LOCK1/2IN.GALV4
2090209WASHER—FLAT1/2IN.GALV4
Part # Parts Required (Per Port) Quanty
4154080BRACKET-FIXEDMOORINGHPEXTREMEHEAVYDUTY2
4154084MOORINGPLUG5/8-11FEMALEBRASSPLUGHPEXTREME2
4154047PLATE-MOORINGHINGEHP22
20905034
4154047
2090704
2090107
2090111
4154048
2090206
Whenconnecngtheporttopart41544047MooringHingefloattheportinandboltittotheholethatis
eitheraligningitsselftotheportbrackethingeorthenextholehigher.Whenboltedthecenterofthe
boltwillbe7”to7.5”abovethewatersurface.

13

1035264RevA
STEP 6: ATTACH TO THE DOCK ‐FIXED DOCK APPLICATION
1.PlacetheLockWasherandWasheronbothBolts.(4151927,2090707&2090212)
2.InserttheMooringPlug(4154084)intothemooringcavityintheEPICbody.
3.HooktheMooringBracket(4154080)intotheMooringCavityontheundersideoftheEPICbody.
3.PivotthebracketuptotheEPICbody.
4.InserttheBoltandWashers(see1.)intotheMooringPlugandghtenunltheBracketissnugagainsttheEPIC
body.
IMPORTANT: Do not exceed the maximum torque requirement of 70 ‐lbs.
REMINDER: TIGHT IS TIGHT AND TOO TIGHT IS BROKEN!
BOLTASSEMBLY
COMPLETE
4151927(X2)
2090707(X2)
2090212(X2)
4154044(X2)
4154084(X2)
ASSEMBLYCOMPLETE
Part # Hardware Required Quanty
4151927BOLT-5/8-11X1.52
2090707LOCKWASHER-5/8GALV2
2090212WASHER-FLT-5/8”GALV2
4154126KIT-BAGHPEXTREMEHARDWAREFIXED1
Part # Parts Required (Per Port) Quanty
4154027KIT-FIXEDDOCKMOORINGHPEXTREME1
4154084MOORINGPLUG5/8-11FEMALEBRASSPLUGHPEXTREME2
4154031KIT-MOORINGKITHPE1
4154032HP-EXTREMEHDFIXEDMOORINGKIT1
4154044BRACKET-FIXEDMOORINGHPEXTREMEHEAVYDUTY2

14

1035264RevA
STEP 7: ATTACH TO THE FIXED DOCK
1.AachFixedDockBracket(4150160)tothedockasshown(3differentmethodsareillustrated).
2.Insertthe4”SCH80PVCPipe(3151300)through4150160andtheFixedMooringBracket(4154044).
3.BolttogetherasshownandghtenunlthePVCPipe(3151300)isheldfirmlyinplace.
IT IS UP TO THE INSTALLER TO DETERMINE IF THE ATTACHMENT IS STRONG ENOUGH.
ADDITIONAL REINFORCEMENT MAY BE NECESSARY IN ROUGH WATER. 
Part # Hardware Required Quanty
4151927BOLT-5/8-11X1.52
2090707LOCKWASHER-5/8GALV4
2090212WASHER-FLT-5/8”GALV2
4154048BOLT—5/8-1161/2IN.GALV2
2090111NUT-HEX5/8-11GALV4
2090507BOLT-HEX1/2-13IN.GALV4
2090705WASHER-LOCK1/2IN.GALV4
2090209WASHER—FLAT1/2IN.GALV4
Part # Parts Required (Per Port) Quanty
4154044BRACKET-FIXEDMOORINGHPEXTREMEHEAVYDUTY2
4154084MOORINGPLUG5/8-11FEMALEBRASSPLUGHPEXTREME2
5049000HDCASTDOCKBRACKETASSEMBLY2
4150160FIXEDDOCKBRACKET2
3151200REINFORCINGBACKPLATE2
31513004”SCH80PVCPIPE48”2
3151500RISERPLATE(OPTIONAL)2
3151600RISER-ANGLEATTACHMENT2
4150160
2090705
2090111
2090503
2090107
2090704
3151500
3151600

OPTIONALMETHODUSING4154044
3151200
4150160
2090507
2090705
2090111
OPTIONALMOORINGPOLLWITHEXTENIONUSINGRISERPLATE3151500

15

1035264RevA
STEP 8: IF SIDE MOORING TO FLOATING DOCK
Part # Hardware Required Qty
4151927BOLT-5/8-11X1.52
2090707LOCKWASHER—5/8GALV2
2090212WASHER-FLT-5/8”GALV2
4154143HPEXTREMEHARDWAREBAGFLOATING 1
4154048BOLT—5/8-1161/2IN.GALV2
Part # Parts Required (Per Port) Qty
4154025KIT—HARDWAREHPEXTREMEFLOATINGDOCK1
4154080FLOATINGMOORING,HPEXTREMEWELDEDCORNERSAND2
4154084MOORINGPLUG5/8-11FEMALEBRASSPLUGHPEXTREME2
4154047PLATE-MOORINGHINGEHP22
4154047
4154025
4154084
4154009
4154048
1.MountthedockbracketsusingthesameinstruconsasinSTEP5,
Whenconnecngtheporttopart41544047MooringHingefloattheportinandbolttheforwardbracket
totheholethatiseitheraligningitsselftotheportbrackethingeorthenextholehigher.Whenboltedthe
centeroftheboltwillbe7”to7.5”abovethewatersurface.Theabracketshouldbeboltedonehole
lowerthanitnaturallyfloats.

16

1035264RevA
STEP 9: CONNECT HYDROPORT TO HYDROPORT
Part # Hardware Required Quanty
4154033KITBAG-HPEXTREMECONNECTINGHARDWARE1
4150010BOLT-HEXHEAD1/2-13X16-3/4IN18-8SS 2
2090208WASHER-FLAT1/2IN.SS2
HH-1916WASHER-LOCK1/2”SCREWSIZE18-8SS2
HDW-06-00021/2"X7-3/4"ALUMINUMPIPE 2
Part # Parts Required (Per Port) Quanty
4154028KIT-CONNECTINGHPEXTREME1
4154016TOPPLUGTHREADED,HPEXTREME2
4154015HPEXTREMEBOTTOMPLUGCONNECTION2
4154029HPEXTREMEINSTALLATIONTOOL1
ASSEMBLETHEPORTS:
1.TherearshowstheConneconPlugsassembledforinstallaon.ThefrontshowshowtheConneconPlugswill
appearwheninstalled.
2.ThetopandboomConneconPlugsareconnectedby4150010butnotghtenedATTHISTIME.
3.TheConneconPlug(4154016)(theshorterofthetwoConneconPlugs)canbeplacedintheMooringPlugcavity
onthefirstportandtheboltplacedthroughthehole.
4.TheBoomConneconPlug(4154015)canthenbethreadedontotheboomofthebolt(4150010),leavingthe
BoomConneconPlug(4154015)veryloose.
5.FloatthesecondHydroPorttothefirstHydroPortwiththeConneconPlugsINSTALLED.PulltheTopConnecon
Plugsupjustenoughtoclearthetopoftheport.
6.TheBoomConneconPlugsshouldsllbelooseenoughtocleartheboom.
7.WhentheHydroPortsarecloseenoughtogether,lowertheTopConneconPlugssothattheyrestinthecavies
createdbytheREMOVEDMooringCaps.
FINALASSEMBLEDPOSITION
LOOSEFORASSEMBLY


4154029
4154015
4154016
4150010
HH-1916
2090208
HDW-06-0002

17

1035264RevA
STEP 10: CONNECT HYDROPORT TO HYDROPORT (con’t)

8.ThetopshouldlooklikethefrontConneconPlug.Seebelow.
9.Inserttool(4154029)betweentheHydroPortsandhooktheBoomConneconPlug.Thetoolwillhelpyouma-
nipulatetheBoomConneconPlugandalignitwiththecavityintheboomoftheHydroPort.
10.Pullthetool(4154029)uptoholdtheConneconPluginthecavity.
11.Tightenthebolt(4150010)whileholdingthetoolfirmlyinposionunlthetopandboomConneconPlugsare
snug.DO NOT OVERTIGHTEN.
An HP Extreme and HP EPIC can seamlessly connect at this point.
Part # Hardware Required Quanty
4154033KITBAG-HPEXTREMECONNECTINGHARDWARE1
4150010BOLT-HEXHEAD1/2-13X16-3/4IN18-8SS 2
2090208WASHER-FLAT1/2IN.SS2
HH-1916WASHER-LOCK1/2”SCREWSIZE18-8SS2
HDW-06-00021/2"X7-3/4"ALUMINUMPIPE 2
Part # Parts Required (Per Port) Quanty
4154028KIT-CONNECTINGHPEXTREME 1
4154016TOPPLUGTHREADED,HPEXTREME 2
4154015HPEXTREMEBOTTOMPLUGCONNECTION2
4154029HPEXTREMEINSTALLATIONTOOL1

18

1035264RevA
Operang Instrucons
Loading
WARNING: Only load PWC when the HydroPort EPICTM is unoccupied.
1.ApproachtheHydroPortEPICatidlespeedonly.
2.PosionthePWC’sbowbetweenentryrollersascloselycenteredaspossible.
3.ApplynecessarythroletodriveontotheplaormunlPWC’sbowrestsonthebow
bumperoftheHydroPortEPIC.
4.TosecurethePWC,dismountandconnecttheStrapHookthroughthefrontmooring
eyeletofPWC.

Launching
1.IfthePWCissecuredwithalockorstrapreleaseitbeforelaunching.
2.BoardPWCandshiweighttowardsrearofcra.
3.Applyarockingmoontoiniatethelaunch.
4.IfPWCwillnotlaunchaerrockingmoonisapplied,dismount.
5.MovetothesideoftheHydroPortEPIC,graspthehandlebarsandseatofthePWC,and
pushbackward.
6.OncethePWCstartstomove,boardthePWCandapplyarockingmoontoiniate
launch.


19

1035264RevA
CONDITION:
PWCwon’tstayontheHydroPortEPICwhenIpullontotheplaorm
POSSIBLE CAUSES:
A.Comingintoofast
B.ThePWC’sweightistoofartotherearoftheHydroPortEPIC
C.WheelLocaons
CORRECTION:
A.TrytojusttouchthebowofthePWCtotheentrypointandgentlythroleon.Whena
PWCridesuponthebowbumperitslidesbackdownandthatmomentumcantakethe
craoffoftheEPIC.
B.Adjustthewheelssothattheforwardwheelsarewiderthanthewheelsattherear.This
willcausethefrontofthecratositlowerthantherear.Thiswillhelpthecrastayon
theHydroPortEPIC;however,itmaymakeunloadingalilemoredifficult.
C.Ifusingthefloangmooringbracket,themounngposioncanbemoveddownone
holeinthebracket,whichwillchangethewaythecrasitsontheplaorm.
CONDITION:
PWCwon’tslideofftheHydroPortEPIC
POSSIBLE CAUSES:
A.ThePWC’sweightistoofarforward
B.WheelLocaons
C.Theleveloftheportisleaningforwardwhentheskiisontheport
CORRECTION:
A.Adjustthewheelssothattheforwardwheelsarenarrowerthanthewheelsattherear.
Thiswillcausethefrontofthecratosithigherontheport.Thiswillhelpthecraroll
offeasier;however,itmaymakeloadingalilemoredifficult.
B.Ifusingthefloangmooringbracket,themounngposioncanbemoveduponehole
inthebracket,whichwillchangethewaythecra sitsontheplaorm.Theeffectsare
similartochangingthewheelposion.
C.Addionalwheelandaxlesetscanbepurchasedtoputintheotherwheelpocket
locaons.Thiswillreducetheweightperwheel,makingthePWCeasiertoroll.

TROUBLESHOOTING

20

1035264RevA
WarrantyandRegistraon
WhatIsNotCoveredByThisWarranty*
HydroHoist®doesnotwarrantanyproduct,component,orpart:
(a)ThatisnotmanufacturedbyHydroHoist®
(b)ThatisnotinstalledorservicedbyemployeesorcontractorsofHydroHoist®oran
AuthorizedHydroHoist®Dealer
(c)Damagedbyfailuretoprovideasuitableinstallaonenvironmentfortheli
(d)Damagedbyuseoftheliforpurposesotherthanthoseforwhichitwasdesigned
(e)Damagedbydisasterssuchasbutnotlimitedtofire,flood,wind,andlightning
(f)Damagedbyunauthorizedaachmentsormodificaons
(g)Damagedbyoperaon,maintenance,orrepairoftheproductcontrarytowrien
instruconsofHydroHoist®
(h)Damagedduringshipment
(i)Damagedbyanyotherabuseormisusebytheuser
(j)Whichhasanalteredordefacedservicenumber
*Termsandcondionscanchangewithoutnoce.Forthelatestwarrantyterms,contactHy-
droHoist®CustomerServiceatcustomerservice@boatli.com


PartsandCustomerServiceContact
Customerservice,parts,andshipping:customerservice@boatli.com

ProductRegistraon
VerifythataHydroHoist®dealerregisteredyourboatli.Ifitisnotregistered,warrantysupportmay
belimited.Visitwww.boatli.comtoregisteryourli.