Hyster H360-36HD Quick start guide

WWW.HYSTER.COM
H360-36/48HD SERIES
TECHNICAL GUIDE

H360-36/48HD DIMENSIONS
Circled dimensions correspond to the line numbers on the tabulated chart inside the Technical Guide. Dimensions are in inches (millimeters).
4-21
4-35
4-4
1-5
1-6
4-1
4-1
4-5
4-2
4-7
1-9
4-20
4-19
4-32
1-8
4-31

H360-36/48HD SPECIFICATIONS
CERTIFICATION: These Hyster®lift trucks meet design specications of Part II ANSI B56.1-1969, as required by OSHA Section 1910.178(a)(2) and also comply with Part III ANSI B56.1-revision in effect at time of manufacture. Certication of compliance with the applicable ANSI standards
appears on the lift truck. Performance specications are for a truck equipped as described under Standard Equipment on this Technical Guide. Performance specications are affected by the condition of the vehicle and how it is equipped, as well as by the nature, condition of the
operating area, proper service and maintenance of the vehicle. If these specications are critical, the proposed application should be discussed with your dealer.
GENERAL
Description Units English Metric English Metric
1-1 Manufacturer HYSTER HYSTER HYSTER HYSTER
1-2 Model designation H360-36HD H360-36HD H360-48HD H360-48HD
1-5 Rated load capacity lbs kg 36,000 16,329 36,000 16,329
1-6 Load center in mm 36 914 48 1219
1-8 Load distance in mm 34.9 887 34.9 887
1-9 Wheelbase in mm 148 3,750 148 3,750
WEIGHTS
2-1 Total truck weight without load lbs kg 47,186 21,403 50,493 22,903
2-2a Axle loading with load front lbs kg 77,110 34,977 79,903 36,243
2-2b rear lbs kg 6,076 2,756 6,590 2,971
2-3a Axle loading without load front lbs kg 23,817 10,803 23,683 10,742
2-3b rear lbs kg 23,369 10,600 26,809 12,160
WHEELS
3-1 Tire type Pneumatic Pneumatic
3-2 Tire size front 12.00x20 Bias 12.00x20 Bias
3-3 rear 12.00x20 Bias 12.00x20 Bias
DIMENSIONS
4-1 Mast tilt, forward / back degrees 15 / 10 15 / 10
4-2 Height of mast lowered in mm 145 3,680 145 3,680
4-3 Freelift (Top of Fork) in mm 000 0
4-4 Lift height (Top of Fork) in mm 156 3,984 156 3,984
4-5 Height of mast extended in mm 222 5,622 222 5,622
4-7 Height to top of operator compartment in mm 120 3,054 120 3,054
4-19 Overall length in mm 310 7,878 310 7,878
4-20 Length to load face in mm 214 5,438 214 5,438
4-21 Overall width over drive tires in mm 100 2,542 100 2,542
4-22a Fork thickness in mm 3.9 100 3.9 100
4-22b width in mm 7.9 200 7.9 200
4-22c length in mm 96 2,440 96 2,440
4-24 Carriage width in mm 100 2,540 100 2,540
4-25a Fork spread, min (in-in) in mm 9235 9235
4-25b Fork spread, max (out-out) in mm 94 2375 94 2375
4-31 Ground clearance, under mast with load in mm 7187 7187
4-32 Ground clearance, center of wheelbase in mm 14 368 14 368
4-33 Minimum aisle width (add load length + clearance) in mm 236 5,984 236 5,984
4-35 Outside turning radius in mm 205 5,199 205 5,199
MISC.
8-7 Hydraulic tank capacity gal l42 160 42 160
8-8 Fuel tank capacity gal l54 206 54 206
10-4 DEF tank capacity gal l5.0 19.0 5.0 19.0
PERFORMANCE
PERFORMANCE WITH TIER 4 FINAL CUMMINS QSB 6.7L ENGINE
5-1a Travel speed with load mph km/h 17 27 17 27
5-1b without load mph km/h 18 29 18 29
5-2a Lifting speed with load ft/min m/s 77 0.39 77 0.39
5-2b without load ft/min m/s 87 0.44 87 0.44
5-3a Lowering speed with load ft/min m/s 106 0.54 106 0.54
5-3b without load ft/min m/s 89 0.45 89 0.45
5-6 Drawbar pull – Max lbs kN 26,700 119 26,500 119
5-7 Gradeability – no load / rated load – 1 mph (1.6 km/h) % 35/31 35/31 33/33 33/33
PERFORMANCE WITH TIER 3 CUMMINS QSB 6.7L ENGINE
5-1a Travel speed with load mph km/h 17 27 17 27
5-1b without load mph km/h 18 29 18 29
5-2a Lifting speed with load ft/min m/s 67 0.34 67 0.34
5-2b without load ft/min m/s 87 0.44 87 0.44
5-3a Lowering speed with load ft/min m/s 106 0.54 106 0.54
5-3b without load ft/min m/s 89 0.45 89 0.45
5-6 Drawbar pull – Max lbs kN 24,500 113 24,300 113
5-7 Gradeability – no load / rated load – 1 mph (1.6 km/h) % 35/27 35/27 33/26 33/26

H360-36/48HD SPECIFICATIONS
RATEDCAPACITIES
Model H360-36HD: 36,000 lbs. at 36” (16,329 kg at 914 mm) load center
Model H360-48HD: 36,000 lbs. at 48” (16,329 kg at 1220 mm) load center
Rated capacities are for trucks equipped with:
• 2-Stage mast to 156” (3984 mm) maximum fork height
• 100” (2540 mm) carriage width
• 96” (2440 mm) long forks
Contact your dealer for other capacity information.
Conversion Factor: 1.0” = 25.4 mm
1 lb = 0.45 kg
POWERTRAINS UNITS TIER 4 FINAL TIER 3
1-3 Power type Diesel Diesel
7-1 Engine Manufacturer / model Cummins QSB 6.7L Cummins QSB 6.7L
7-1a EPA Tier Compliance Tier 4 Final Tier 3
7-2a Engine power output - Rated hp kW 164 122 155 116
7-2b Engine power output - Peak hp kW 168 125 155 116
7-3 Governed speed rpm 2,300 2,300
7-4 Number of cylinders / displacement # / l 6/6.7L 6/6.7L
7-5 Engine torque - Max lb-ft N-m 540 732 443 600
7-5a Turbocharger Type Variable Geometry,
Water Cooled Wastegate
7-8 Alternator output Amps 120 120
8-0 Transmission Manufacturer / model ZF WG-161 ZF WG-161
8-1 Transmission type & speeds Powershift 3F x 3R Powershift 3F x 3R
7-10 Battery voltage, rated capacity V / CCA 2 x 12 / 900 2 x 12 / 900
7-10a Drive Axle Manufacturer / model Kessler D81 Kessler D81
5-10 Service brake Oil immersed (wet) disc Oil immersed (wet) disc
5-11 Park brake Spring apply, dry disc Spring apply, dry disc
10-1 Working pressure for attachments psi Mpa 2,828 19.5 2,828 19.5
10-2 Oil ow for attachments gpm l/m 26.4 102 26.4 102
H360-36/48HD MAST DIMENSIONS
4.4 Lift height
(Top of Fork) 4.2 Mast Lowered Ht. 4.3 Freelift (Top of Fork) 4.5 Overall Extended Ht.
in mm in mm in mm in mm
2-STAGE NO FREE-LIFT (NO FL)
156 3984 145 3680 00222 5622
180 4594 157 3984 00246 6232
212 5406 173 4390 00278 7044
244 6219 189 4797 00310 7858
NOTE: Higher capacity rated versions up to 40,000 lbs. at shorter load centers are available upon request on a custom basis.
Please contact Hyster Company for details & SPED Quote.
20000
25000
30000
35000
40000
24 28 32 36 40 44 48 52 56 60 64 68 72
RATED LOAD (lbs)
LOAD CENTER (in)
H360-36HD
H360-48HD
RATED LOAD vs. LOAD CENTER
DFSSFP CARRIAGE w/ QD FORKS
U.S. CUSTOMARY
20000
25000
30000
35000
40000
24 28 32 36 40 44 48 52 56 60 64 68 72
RATED LOAD (lbs)
LOAD CENTER (in)
H360-36HD
H360-48HD
RATED LOAD vs. LOAD CENTER
APRON SIDE SHIFT PIN TYPE CARRIAGE
U.S. CUSTOMARY
20000
25000
30000
35000
40000
24 28 32 36 40 44 48 52 56 60 64 68 72
RATED LOAD (lbs)
LOAD CENTER (in)
H360-36HD
H360-48HD
RATED LOAD vs. LOAD CENTER
STD PIN TYPE CARRIAGE
U.S. CUSTOMARY
RATED LOAD (lbs)
LOAD CENTER (in)
RATED LOAD (lbs) RATED LOAD (lbs)
40000
40000 40000
35000
35000 35000
30000
30000 30000
25000
25000 25000
20000
24 28 32 36 40 44 48 52 56 60 64 68 72
20000 20000
20000
25000
30000
35000
40000
24 28 32 36 40 44 48 52 56 60 64 68 72
RATED LOAD (lbs)
LOAD CENTER (in)
H360-36HD
H360-48HD
RATED LOAD vs. LOAD CENTER
DFSSFP CARRIAGE w/ INTEGRATED FORKS
U.S. CUSTOMARY
LOAD CENTER (in)
LOAD CENTER (in)
LOAD CENTER (in)
24 28 32 36 40 44 48 52 56 60 64 68 72
24 28 32 36 40 44 48 52 56 60 64 68 72
24 28 32 36 40 44 48 52 56 60 64 68 72
RATED LOAD (lbs)
40000
35000
30000
25000
20000
H360-48HD+
H360-36HD+
H360-48HD
H360-36HD
H360-36HD+
H360-48HD+
H360-36HD
H360-48HD
H360-48HD+
H360-36HD+
H360-48HD
H360-36HD
H360-36HD+
H360-48HD+
H360-36HD
H360-48HD

STANDARDFEATURESANDOPTIONS
MASTS
Masts with nested channels provide maximum visibility of the
attachment and load. Mast channels, rollers, stub shafts and chain
anchors are reinforced to provide good torsional rigidity. Oversized
stub shafts are inset and double welded for good impact resistance.
Chains designed on outside of mast to enhance visibility window.
CARRIAGES
Pin-type; integral pin-type fork positioner with simultaneous or
individual fork control; pin-type integral sideshift; integral pin-type
dual function sideshift fork positioner; apron style sideshift fork
positioner with simultaneous or individual fork control.
Overall width is 100” (2540 mm) for the H360-36/48HD
Minimum inside-to-inside fork spacing - model and attachment
dependent is 9” (235 mm)
Maximum outside-to-outside fork spacing - model and attachment
dependent is 94” (2375 mm)
FORKS
Three kinds of forks are offered in two sizes.
i. PIN TYPE - STANDARD PROFILE available in:
– 96” long x 3.9” x 7.9” (2440mm x 100mm x 200mm)
– 96” long x 3.5” x 9.8” (2440mm x 90mm x 250mm)
ii. INTEGRAL PIN TYPE (FOR USE WITH DFSSFP) available in:
– 96” long x 3.9” x 7.9” (2440mm x 100mm x 200mm)
– 96” long x 3.5” x 9.8” (2440mm x 90mm x 250mm)
iii. QD HOOK TYPE (FOR USE WITH DFSSFP - QUICK
DISCONNECT) available in:
– 96” long x 3.9” x 7.9” (2440mm x 100mm x 200mm)
– 96” long x 3.5” x 9.8” (2440mm x 90mm x 250mm)
STANDARD ENGINE - TIER 4 FINAL
QSB 6.7L 6 cylinder diesel engine delivers 164 hp (peak 168 hp)
and 540 lb-ft of maximum torque. EPA Tier 4 Final compliant engine
features cooled exhaust gas recirculation (EGR) technology with
selective catalytic reduction (SCR); water-cooled variable geometry
turbocharger with an integrated Diesel Exhaust Fluid (DEF) delivery
system. Innovative selectable ECO performance modes offer
excellent fuel economy and maximum productivity. Also includes:
• 120 amp alternator
• Viscous, on-demand cooling fan which saves fuel and reduces
noise
• Low mount exhaust with diesel oxidation catalyst (DOC) and a
diluter to reduce exhaust temperatures
• Requires ultra-low sulfur diesel fuel and low-ash oil
• Heavy duty spinner type Sy-Klone pre-cleaner center stacked for
ease of service and enhanced visibility
TRANSMISSION
• ZF WG-161 three-speed, fully reversing powershift transmission
produces smooth shifting, precise inching and fast acceleration
• 3 forward and 3 reverse gears
• Smooth fully automatic gear shift control
• Powershift transmission with proportional valves
• Inching electronically controlled
• Cushioned clutch lock-up provides smooth shifting and dampens
drive line shock loads
• Simple push button calibration
• Transmission lock-out preventing high speed directional changes
• Transmission and engine powertrain protection for excessive
engine coolant temperature, low engine oil pressure, and
excessive engine inlet air temperatures
ELECTRICAL SYSTEM
• Sealed Deutsch connectors
• CANbus system for easy diagnostics of engine, transmission and
hydraulics
HYDRAULIC SYSTEM
Hyster on-demand load sensing hydraulic system introduces an
efcient way to meet truck’s hydraulic load demands:
• Based on Variable Displacement Pump (VDP) technology
• Pump is only pumping when oil is needed
• Less heat is produced - oil and lters last longer. Hoses, seals,
and components also wear less and last longer
• Engine runs quieter and at lower speeds, extending life of major
components
• Leak free O-Ring Face Seal (ORFS) ttings standard throughout
the truck
• Capable of more oil displacement even at low engine speeds
STEERING SYSTEM
• Designed for high loads and long life, the one piece axle frame
carries the axle loads and provides mounting for the spindles and
cylinder
• Axle spindles are supported by oil bathed wheel bearings and
sealed to prevent contamination entry or loss of oil. This ensures
that oil bearings are always lubricated and enhances overall
durability of the axle spindles
• No steering linkage adjustments are required. Lubricating ttings
on tie rod pins are the only regular maintenance points
• Load sensed steering provides low steering effort and good
performance at all engine speeds
• Fully adjustable steering angle limiter with mechanical stops -
reduces tire scrubbing
• Wheel hubs rotate on large tapered roller bearings
• Non-adjustable tie rod ends provide maximum life
DRIVE AXLE
• Rugged Kessler D81 drive axle features full-oating design
BRAKES
• Oil cooled wet disc brake system
• Designed for load capacities up to 40,000 lbs.
• Axle loads up to 540 kN (121,400 lbs)
• Bolt circle diameter 16.7 inches (425 mm)
• Park brake
OPERATORAREA
• Ergonomically designed hydraulic controls and high/low range
control lever are within easy reach
•
Three steps and hand grips provide easy access to operator
compartment
• Angled oor plate and pedals are positioned for operator comfort
• Telescopic, tilt steer column
• Supportive mechanical full-suspension seat adjusts 8 inches (200
mm) for operator comfort
• Several air suspension seat options are available
• Steel overhead guard frame provides maximum high-stacking
visibility
• Operator Presence System (OPS) with complete hydraulic lock
out requires the operator to be in the normal operating position
before any travel or movement of the mast, tilt, carriage, and
attachment can be initiated and that the travel or movement of
the mast, tilt, carriage, and attachment is locked out when the
operator leaves the seat for more than 2-3 seconds
• Optional light groups aid visibility in low-lighted areas. Light
kits featuring innovative high-performance LED and halogen
technology are available
• Optional ComforCabII features: tinted, curved glass; circulation
fan; heater & defroster; electric wiper and windshield washer
front, rear, top; intermittent front wiper; door retainer; 3 speed
fan; 12-volt auxiliary power source; dome light, with many
additional options to enhance comfort and productivity
Special attachments, equipment or accessories not listed above may be available through
Applications Engineering for specic application requirements.

Hyster Company
P.O. Box 7006
Greenville, North Carolina
27835-7006
Part No. H360-36/48HD/TG
11/2017 Litho in U.S.A. Trucks may be shown with optional equipment. © 2017 Hyster Company. All rights reserved.
Hyster, , and STRONG PARTNERS. TOUGH TRUCKS. are registered trademarks in the United States
and certain other jurisdictions. Cummins, ZF, Kessler and Sy-Klone are registered trademarks of their
respective companies. Hyster products are subject to change without notice.
Visit us online at www.hyster.com or call us at 1-800-HYSTER-1.
STANDARDEQUIPMENT
• 156” maximum fork height 2-stage mast with 145” overall
lowered height
• 100” (2540mm) wide pin type carriage
• 96” long x 3.9” x 7.9” (2440mm x 100mm x 200mm)
pin type forks
• Cummins QSB 6.7L Tier 4 Final engine
• Sy-Klone spinner type heavy duty air intake pre-cleaner
• Premium ZF WG161 3 speed autoshift transmission
• Kessler heavy duty planetary drive axle with wet disc
brakes
• Powertrain Protection system for engine and transmission;
high temperature or low oil pressure
• On-Demand load-sensing hydraulic system featuring
Variable Displacement Pump technology (VDP)
• CANbus electrical control system for engine, transmission
and hydraulics
• Low mount exhaust
• Low mount air intake
• 12.00 x 20 - 20PR bias high load pneumatic drive and steer
tires
• Directional control lever with direction change interlock
system
• UL Classication D
• Mast tilt: 15° fwd / 10° back
• Lockable battery disconnect switch
• Open operator compartment with integral overhead guard.
Compartment includes: seat-side mini-lever hydraulic
control; multifunction display panel; interior wide angle
mirrors; handrails for operator entry and exit; telescoping
& tilting steering column; oor mat; isolated mounting
for low noise and vibration; 24-12V DC converter; full
suspension vinyl seat with integrated, adjustable armrest
and 2-point high visibility seat belt
• Operator restraint system
• Operator presence system
• Electric air horn (105 dBA)
• Audible backup alarm
• 24V electrical system
• Tilting operator compartment for service access – manual
operation
• Light kit #1 - Rear: 2 LED stop, tail and back-up lights
• Steering angle limiter with mechanical stops
• Non-locking fuel cap
• Operator’s manual
OPTIONAL EQUIPMENT
• Cummins QSB 6.7L Tier 3 engine*
• Masts - various lift heights available
• Sideshifting carriages and fork positioners
• Various fork options
• Various mast tilt ranges
• Multifunction joystick
• MONOTROL®pedal direction control with direction change
interlock system
• Radial and pneumatic-shaped solid tires
• Enclosed cab, with or without air conditioning
• Multiple inside-cabin options
• Multiple seat options
• 3-point high visibility seat belts
• Powered tilting operator compartment for service access
• Visible alarm / amber strobe light
• Various high performance LED (light emitting diode) and
halogen light kits available
• Lockable fuel cap
• High mount exhaust
• High mount air intake
• Hydraulic accumulator
• Various traction speed limiters
• Empty seat engine shutdown - adjustable from 3-15
minutes (preset to 15 minutes)
• Lifting eyes
• Steer wheel lug protection
• Engine block heater (110V or 230V)
• Front and rear mud aps
• H-pattern wiper on front windshield
• Mechanical mast tilt indicator
* For Latin American markets only
STANDARDFEATURESANDOPTIONS