Hytronik HC038V User manual

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 1/7
Special photocell to measure and differentiate natural light from LED light
Photocell Advance
Daylight harvest function to regulate light output for maintaining required lux level
5-Year Warranty
Zero crossing detection circuit reduces in-rush current and prolongs relay life (HC038V)
Optional 1-10V or DALI dimming control method
Ambient daylight
threshold One-touch daylight learning via remote control
Loop-in and loop-out terminal for efcient installation (HC038V)
Loop in
Loop out
Lux off function, daylight threshold prior to motion detection
Photocell
Intelligent
Daylight Harvest PIR Sensor
HC038V HCD038
Detached Linear Version with Remote Control
Applications
Occupancy detector with daylight harvest suitable for indoor use.
Suitable for building into the xture:
Ofce / Commercial Lighting
Classroom
Use for new luminaire designs and installations
Features
IP20RED
Technical Data
Input Characteristics
EMC standard (EMC)
Safety standard (LVD)
Certication
Radio Equipment (RED)
EN55015, EN61000
Semko, CB, CE , EMC, RED, RCM
EN60669, AS/NZS60669
EN300440, EN301489,
EN62479
Safety and EMC
Sensor Data
Model No.
360O
PIR Detection
5VDC
Sensor principle
Operation voltage
Detection range
Detection angle
Max. ( Ox H) 6m x 3m
Stand-by power
Model No.
220~240VAC 50/60Hz
Mains voltage
Load ratings:
HC038V
HCD038
<0.5W
400VA (capacitive)
30mA, 16VDC (max. 15 devices)
20s
Warming-up
HC038V HCD038 HIR01 HIR01/FM HIR03
800W (resistive)
Tc: +80
O
C
Operation temperature
Case temperature (Max.)
Ta: -20
O
C~ +55
O
C
Environment
IP20
IP rating

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 2/7
Photocell Advance
TM
30
35
39.5
30
2.5
1.5
16
23.3
25.8
1-10V-
RJ12 connector
RJ12 connector Push
L’
N
L
N
L
N
DALI
Push
1-10V+ 120
30
21
4.5
110.5
4.5
PIR Sensor Head
Model HIR01/FM
PIR Sensor Head
Model HIR01
PIR Sensor Head
Model HIR03
Lens
RJ12 connector
Installation hole
Sensor Main Body
HCD038 (DALI output)
There are three different PIR sensor antenna modules to choose from:
HC038V (1-10V output)
Loop in
Loop out
Ambient daylight
threshold
Photocell
Intelligent
3
0
5
Detection Pattern
Lens
RJ12 connector 40.9
44.5
16.4
19.3
17.8
15.9
12.9
Ø13.8
17
38.9
20.3 21.5 26.5 35.3
Ø48
Lens
Note:We recommend the mounting distance between sensor to sensor should be more than 2m to prevent sensors from
false-triggering.

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 3/7
Daylight Harvest
Light will not switch on
when natural light is
sufcient, even there is
motion detected.
The light switches on
automatically with
presence when natural
light is insufcient.
The light turns on at full or dims to maintain the lux level. The light output
regulates according to the level of natural light available.
The light dims to stand-by
period after hold-time and
stays on selected minimum
dimming level.
The light switches off when
the ambient natural light is
sufcient.
The light switches off
completely after the
stand-by period.
Functions and Features
Photocell AdvanceTM Function (HIR03)
2
It’s well known that LED lights have a totally different spectrum to natural light. Hytronik uses this principle and comes up with special
photocell and sophisticated software algorithm to measure and differentiate natural light from LED light, so that this photocell can
ignore the LED light and only respond to the natural light.
Our technology has no infringement to the existing patents in the market.
1
Note:
The Light automatically dims down and
eventually turns off if the natural light lux
level exceeds the daylight threshold.
However, if the stand-by period is preset
at “+∞”, the xture never switches off
but dim to minimum level, even the
natural light is sufcient.
Lux Off Function
3
The light turns off automatically whenever surrounding natural light lux level exceeds the daylight threshold for more than 5min, even
there is motion detected. However, if the stand-by period is pre-set to innity “+∞”, the xture never switches off but stays at dimming
level, even when natural light is sufcient .
* Short Push (<1s): on/off function;
On →Off: the light turns off immediately and cannot be triggered ON by motion until the expiration of pre-set hold-time. After this
period, the sensor goes back to normal sensor mode.
Off →On: the light turns on and goes to sensor mode, no matter if ambient Lux level exceeds the daylight threshold or not.
* Long Push (>1s): adjust the target lux level by turning the light up or down. Both the adjustment on RC and push switch can overwrite
each other, the last adjustment remains in memory.
Note: if end-user do not want this manual override function, just leave the “push” terminal unconnected to any wire.
Manual Override
4
This sensor reserves the access of manual override function for end-user to switch on/off, or adjust the target lux level by push-switch,
which makes the product more user-friendly and offers more options to t some extra-ordinary demands:

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 4/7
Wiring Diagram
LED Driver
LED Driver
N
L
1-10V+
1-10V
-
N
L
1-10V+
1-10V
-
HC038V
1-10V+
1-10V
P
L’
N
N
L
-
L
N
DALI Driver
DALI Driver
DALI
DALI
L
N
DALI
DALI
L
N
HCD038
DALI
DALI
Push
N
L
L
N
zero-cross point
Alternating current
Zero-cross Relay Operation (HC038V)
Designed in the software, sensor switches on/off the
load right at the zero-cross point, to ensure that the
in-rush current is minimised, enabling the maximum
lifetime of the relay.
5
Detection Pattern
walking towards
walking across
tangential movement 6m
radial movement 3.2m
3m

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 5/7
Press these two buttons to adjust the light output brightness and set a new target lux level. The daylight sensor can measure ambient
daylight level and ignore the LED light, so as to calculate how much articial light is needed to maintain the target lux level.
Settings (Remote Control HRC-11, for HIR03)
Permanent ON/OFF function
Press button “ON/OFF” to select permanent ON or permanent OFF mode.
* Press button “AUTO”, “RESET” or “Ambient” to quit this mode.
The mode will change to AUTO Mode after power failure.
AUTO mode
Press button “AUTO” to initiate automatic mode. The sensor starts working and all
settings remain as before the light is switched ON/OFF.
1. Press button “Shift”, the red LED ashes for indication.
2. Press button “SEMI-AUTO/AUTO” to initiate semi-auto mode. The xture is
manually turned on by pressing the push-switch, and goes off automatically after
stand-by time. (Absence detection mode)
ON/
OFF
SEMI-AUTO mode
Press button “RESET”, all settings go back to default values.
Reset Settings
Press the buttons to select light output at 80% (at initial 10,000 hours) or 100%.
Note: “Sensor off” and “Twilight” functions are disabled.
Power output
Brightness +/-
Scene program - 1-key commissioning
1. Press button “Start” to program.
2. Select the buttons in “Detection range”, “Daylight threshold”, “Hold-time”, “Stand-by time”, “Stand-by dimming level” to set all
parameters.
3. Press button “Memory” to save all the settings programmed in the remote control.
4. Press button “Apply” to set the settings to each sensor unit(s).
For example, to set detection range 100%, daylight threshold Disable, hold-time 5min, stand-by time +∞, stand-by dimming level 30%, the steps should be:
Press button “Start”, button ”100%”, “Disable”, “Shift”, “5min”, “Shift”, “+∞”, “30%”, “Memory”. By pointing to the sensor unit(s) and pressing “Apply”, all
settings are passed on the sensor(s).
Detection range
Buttons in zone “Detection range” are disabled.
Press buttons in zone “ Daylight threshold” to set daylight sensor at 2Lux/ 10Lux / 50Lux / 100Lux / 300Lux / 500Lux / Disable.
Note: To set daylight sensor at 100Lux / 300Lux / 500Lux, press “Shift” button rst.
Daylight threshold
&
A
4
4 hhh
HRC-11
Press button “Shift”, the LED on the top left corner is on to indicate mode selection.
All values / settings in RED are valid for 20 seconds.
Shift Button

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 6/7
1. Press button “Shift”, the red LED starts to ash.
2. Press button “Ambient”, the surrounding lux level is sampled and set as the new daylight threshold.
Ambient daylight threshold
Dual tech & RF mode
Hold-time
Stand-by dimming level
Stand-by time (corridor function)
Press buttons in zone “hold-time” to set the hold-time at 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min.
Note: 1. To set hold-time at 30s / 5min / 15min / 30min, press “Shift” button rst.
2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.
*To exit from Test mode, press button “RESET” or any button in “Hold-time”.
Press buttons in zone “stand-by time” to set the stand-by period at 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞.
Note: “0s” means on/off control; “+∞” means the stand-by time is innite and the xture never switches off.
Press the button in zone “stand-by dimming level” to set the stand-by dimming level at 10% / 20% / 30% / 50%.
All buttons in this zone are disabled.
Settings (Remote Control HRC-01, for HIR01)
Reset function
Permanent ON/OFF function
Sensor mode
Press “Auto Mode” button, the sensor starts to function and all settings remain the same
as the latest status before the light is switched on/off.
Press the “ON/OFF” button, the light goes to permanent on or permanent off mode, and
the sensor is disabled.
* Press “Auto Mode”, “RESET” or “Scene mode” buttons to quit this mode.
The mode will change to AUTO Mode after power failure.
ON/
OFF
Auto Mode
Dim +/
RESET
+
-
HRC-01
Note: the buzzer beeps one time
when RC receives signal successfully.
+
8
SC1 SC2 SC3
SC4
100%
30S 1min
1min
1H
5min
5min
10min
10min
20min
0S 10S
30min
30min
8H
TEST
2S
75% 50% 10%
10% 20% 30% 50%
SC5SC6
RESET
Auto Mode
Scene mode
Detection range
Hold-time
Stand-by-period
Stand-by dimming level
+
-
Dim
ON/
OFF
Press “RESET” button, all settings go back to default value (same as scene mode 3):
Detection range: 100%; Hold-time: 5min; Stand-by period: 10min;
Stand-by dimming level: 20%; Constant lux: 100lux
Press these two buttons to adjust the light output brightness and set a new target lux
level. The daylight sensor can measure ambient daylight level and ignore the LED light,
so as to calculate how much articial light is needed to maintain the target lux level.
Auto-conguration function
All buttons in this zone are disabled.

Additional Information / Documents
1. For full explanation of Hytronik Photocell AdvanceTM technology, please kindly refer to
www.hytronik.com/download ->knowledge ->Introduction of Photocell Advance
2. Regarding precautions for microwave sensor installation and operation, please kindly refer to
www.hytronik.com/download ->knowledge ->Microwave Sensors - Precautions for Product Installation and Operation
3. Regarding Hytronik standard guarantee policy, please refer to
www.hytronik.com/download ->knowledge ->Hytronik Standard Guarantee Policy
Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 7/7
8H permanent on mode
In some circumstances, people want to disable the sensor and keep the light on for a certain period of time, even there is no motion
detected. This function is built-in the software and can be achieved by pressing the “8H” button on the RC.
* Press “ON/OFF”, “Auto Mode”, “RESET” or “Scene mode” buttons to quit from this mode.
8H
Scene mode
There are 6 scene modes xed program built-in the remote control to choose for different applications:
Scene options Hold-time Stand-by period Stand-by dimming level Constant Lux Detection range
SC1 1min 1min 10% 50Lux
SC2 3min 5min 20% 75Lux
SC3 5min 10min 20% 100Lux
SC4 10min 30min 30% 150Lux
SC5 20min 1H 30% 200Lux
SC6 30min +∞ 50% 400Lux
Detection range
Buttons of “detection range” are disabled.
Hold-time
Press the buttons of “hold-time” to set hold-time at 30s / 1min / 5min / 10min / 20min / 30min .
Stand-by period (Corridor function)
Press the buttons of “stand-by period ( corridor function)” to set stand-by period at 0s/10s/1min/5min/10min/30min/1H/+∞.
Stand-by dimming level
Press the buttons of “stand-by dimming level” to set the stand-by dimming level at 10%/20%/30%/50%.
Note: “0s” means on/off control; “+∞” means bi-level dimming control and the xture never switches off.
disabled
disabled
disabled
disabled
disabled
disabled
* End-user can adjust the settings by pressing buttons of detection range/hold-time/stand-by period/stand-by dimming
level/daylight sensor. The last setting stays in validity.
Test mode
This button is for testing purpose only. The sensor goes to test mode (hold-time is 2s) after commissoning, meanwhile the stand-by
period and daylight sensor are disabled.
* This mode can be ended by pressing “reset”, or any button of “scene mode” and “hold-time”. The sensor settings are changed
accordingly.