i3 International Ax47R series User manual

CAMERA PARTS AND DEFINITIONS
Thank you for purchasing i3 International’s Ax47R/67R mini IP dome camera.
Your camera is equipped with a fixed 2.8mm @ F1.8 or 4.0mm @ F1.6 lens.
This camera series is compatible with the optional T-Grip, T-bar ceiling clip, (Part#: B8) for
easy one-hand installation on most Standard 1” drop-ceiling grid types.
SAFETY
When installing your Ax47R/67R camera be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light and unstable light sources
• temperatures below -20° C (-4° F) and above 50° C (122° F).
To avoid electrical shock and to preserve the product warranty, DO NOT disassemble the
camera. Refer servicing to qualified personnel only.
POWER SUPPLY
This camera accepts PoE power.
Ensure the supplied voltage meets the power consumption requirements of this camera
before powering the camera on. Incorrect voltage may cause irreparable damage to the
video camera and will effectively void the camera warranty.
CLEANING
• For maximum optical clarity, the camera dome or lens must remain clean. Use a soft,
dry cloth to remove finger prints or dust from the dome cover.
• Use a blower to remove dust from the lens.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may dam-
age the surface finishes.
PACKAGE CONTENTS
Ensure that the items received match those listed on the order form and the packing slip.
In addition to this manual and a fully assembled camera, the dome camera packing box
includes:
1. Surface Mount template x1
2. Desiccant (attach to the inside of the Inner Liner) x1
3. Security torx bit x1
4. Round Head Screw (Tapping Type) x3
5. Plastic Anchor x3
6. Standard RJ45 Connector x2
1. Stand-offs for the optional T-Grip (B8) installation. Attach B8 with two provided
screws, if using. See Drop-Ceiling Installation section for more information.
2. Mounting holes (x3)
3. Dome cover
4. Screws securing the dome cover to camera module (x3, silver)
5. Dome bubble
6. Screws attaching camera module to the camera base (x4, black)
7. Tilt bracket with two locking screws. Loosen the screws and tilt to adjust
lens angle.
8. Inner Liner / Shroud. Attach the desiccant to the inside of the Inner Liner,
without obstructing the lens movement.
9. IR board
10. Camera Lens Assembly. Pan to adjust lens angle.
11. Lens base. Rotate to adjust lens angle.
12. Camera lens.
13. RJ45 Ethernet PoE Port with waterproof RJ45 connector assembly.
Insert an Ethernet cable into the port for network connection as well as PoE
(Power over Ethernet) power. To maintain water-resistant rating in outdoor
installations, make sure to use the included waterproof RJ45 Connector
assembly.
14. Reset/Default button. Press for 1 second to reboot the camera.
Press for 6 seconds to restore camera settings to factory defaults.
15. MicroSD Card slot for on-camera video storage. (MicroSD card sold
separately).
110.97 mm
82 mm
4
5
3
6
7
9
8
10
12
11
13
14
15
50.5 mm
2
2
2 3 4 56
Logo Direction
Cable hole
3-Ø4.5 holes
(for plastic anchor)
1
1.3/3MP Infrared Mini Outdoor IP Dome Camera
Ax47R/67R
User Manual
i3-TRNG-CAMS-Ax47R_67R_T-Grip.indd
Rev. 200416
QR Code for Complete
User Manual and ACT
Scan this QR code or visit ftp.i3international.com to view
and download AnnexxusConfigurationTool v1.5 (ACT) and
the full User Manual.
Contact our Technical Support team at: 1.877.877.7241 or
[email protected] if you have any questions
or concerns regarding camera installation or if you require
software services or support.
2
1

Ax47R/67R IP Dome Camera
QUICK START GUIDE
DROP-CEILING INSTALLATION
Ax47/67 camera series is compatible with i3’s B8, T-bar ceiling clip (T-Grip) for easy one-
hand indoor installation onto most Standard 1” drop-ceiling grid types.
For easier installation, remove the ceiling tiles to expose the T-bar grid.
1. Use the two screws provided with B8 to attach it to the two stand-offs on the back of
Supported mounting options
See the table below for additional mounting
options supported by Ax47R/67R camera series.
Compatible Mounting Accessories:
B7 - back box for pendant installations
DB60 - goose-neck bracket
DB60CPM - corner/pole mount kit (use with DB60)
Mounting Type Additional Accessories required
Drywall / block wall mount
Surface mount (E.g. drop ceiling tile) None
Pendant Mount
Electrical (Round/Hex, Single Gang) Box B7
Horizontal Wall Mount B7 + DB60
Pole Mount
Corner Mount B7 + DB60 + DB60CPM
i3 INTERNATIONAL INC. 1.866.840.0004
www.i3international.com
7. Cut the cable entry hole in the ceiling tile as required, then
pass the camera’s cable through.
8. Adjust the lens position for the preferred field of view by panning,
tilting and rotating the camera lens assembly.
Tip: Lift the inner liner for easier lens adjustment.
the Ax47/67 camera.
2. Loosen three screws securing the dome cover to camera
module with the Torx bit (provided). Do not completely
remove the screws from the dome cover.
3. Gently pull the dome cover downwards and set aside.
4. Hold the camera firmly against the T-bar grid with the
T-Grip clip on a slight angle, as shown in the
Diagram A.
5. Rotate the camera clockwise until the clip engages with
the T-bar and clicks into place.
6. Slide the camera on the T-bar to adjust the camera
position as shown in the Diagram B (Optional).
The rubberized T-Grip tips will prevent any scratches.
Important: Do not over-rotate the
camera lens assembly beyond the stop
point to prevent twisted, disconnected,
or broken internal cables/components.
3-axis Range Limitations:
Pan range : 360°
Rotate range : ±175°
Tilt range : 20°~90°
Diagram B
9. Attach the desiccant to the inside of the inner liner, then replace camera’s inner liner
until it snaps back into place.
10. Replace the camera dome cover and re-tighten 3 silver screws securing the dome
cover to the camera base.
Rotate
Diagram A
2
1
CAMERA REMOVAL
1. To disengage the T-Grip from the T-bar
grid, press down on both rubberized
T-Grip tips as shown in Diagram C.
2. Rotate the camera counter-clockwise
to remove it from the T-bar.
2
1
1
Diagram C
*Important: For the security of your camera and of all connected devices,
i3 International recommends that you change your camera’s default administrative
password in the camera’s User Management setup tab. Keep your passwords secure.
Change your Annexxus camera’s default IP Address:
Annexxus Cameras cannot share an IP address, each camera requires its own unique
IP address.
1. Connect your Annexxus camera to the Gigabit switch.
2. On your i3 NVR, launch i3 Annexxus Configuration Tool (ACT) v.1.5 or higher.
You can download and install the latest ACT installation package from i3 website:
https://i3international.com/download
3. Select your Annexxus camera in the ACT list.
4. Enter the new IP address and Subnet Mask of the camera in the Device(s)
Communication Update area.
5. Click Update and then Yes in the confirmation window.
Tip: New IP address must match the IP range of LAN or NVR’s NIC1.
6. Wait a few moments for a “Success” message in the Result field.
Repeat Steps 1-6 for all detected Annexxus cameras OR
7. Assign IP range to multiple cameras by selecting two or more
cameras in ACT, then entering the starting IP address and the final IP octet for
your IP range.
Click Update and then Yes in the confirmation window.
Wait until “Success” message is shown for all selected cameras.
Ensure you can connect to your camera(s) using its new IP Address:
1. Open an Internet browser window and enter the new IP Address you have just
assigned to your Annexxus camera in Step 4 (or 7).
2. Enter the camera User Name and Password in the pop-up login window.
3. Annexxus camera interface will be displayed in the Internet Explorer window.
You should be able to see the camera image on the screen. If you do not see
the camera image on the screen, call i3 International technical support team for
troubleshooting tips: 1.877.877.7241
ADDING CAMERA TO i3 PRO SETUP v7
1. Launch the i3 Pro Setup from the Desktop or from the SRX-Pro Monitor.
2. In the IE browser, click Continue to this website.
3. Enter your administrator Username and Password and click LOGIN
4. Click on the Add tile.
5. All cameras recognized by i3’s GiPi and ONVIF will be shown in the
UNASSIGNED CAMERAS tab.
6. Select one or more Annexxus 47/67R cameras with the same login credentials
and click LOGIN
7. Enter camera’s Username and the Password and click SAVE
Login status for your device must now show the green checkmark .
Note: Devices with “Login failed” status will not be added.
8. Click ADD . Your IP devices have been added to i3 Pro Setup and are
recording based on Sensor + Motion schedule.
Change resolution and frame rate for each camera in the List section of the
i3 Pro Setup.
CHANGING IP ADDRESS in ACT
Camera’s default IP address: 192.0.0.16.
Camera’s default Subnet mask address: 255.255.255.0.
Credentials*: Login - i3admin / Password - i3admin
Or
Tilt
Pan