IBM xSeries 345 User manual

Option Installation Guide
xSeries 345
Type 8670

IBM xSeries 345
Type 8670
Option Installation Guide
SC48-P971-90
򔻐򗗠򙳰

Note:
Before using this information and the product it supports, be sure to read the general information in “Notices” on page 43.
First Edition (July 2002)
© Copyright International Business Machines Corporation 2002. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.

Contents
Safety ............................v
Chapter 1. Introduction......................1
Notices and statements in this book .................1
Major components of the xSeries 345 Type 8670 server ..........2
Component locations .......................3
System-board option connectors ..................3
PCI riser-card option connectors ..................3
System-board internal cable connectors ...............4
System-board external port connectors ...............5
System-board switches and jumpers ................6
System-board LED locations ...................8
Chapter 2. Installing options....................9
Installation guidelines .......................9
System reliability considerations ..................9
Working inside the server with the power on .............10
Handling static-sensitive devices .................10
Server power features ......................11
Turning on the server .....................11
Turning off the server .....................12
Standby mode ........................12
Removing the cover and bezel ...................13
Working with adapters ......................14
Adapter considerations .....................15
Installing an adapter ......................16
Installing a ServeRAID-5i controller ................19
Installing a hot-swap drive.....................20
Installing memory modules ....................21
Installing an additional microprocessor ................23
Installing a hot-swap power-supply option ...............28
Replacing a hot-swap fan .....................30
Replacing the battery ......................31
Completing the installation.....................33
Installing the server cover and bezel ................33
Updating your server configuration.................33
Connecting external options ...................34
Cabling the server.......................34
Installing the server in a rack...................35
Chapter 3. Input/output ports ...................37
Video port...........................38
Keyboard port .........................38
Auxiliary-device (pointing device) port ................38
Ultra320 SCSI controller system-board connectors............39
SCSI cabling requirements ...................39
SCSI IDs ..........................39
SCSI connectors .......................40
Serial port...........................40
Viewing or changing the serial-port assignments ...........40
Serial-port connector......................40
Universal Serial Bus version 1.1 ports ................41
USB cables and hubs .....................41
© Copyright IBM Corp. 2002 iii

USB-port connectors......................41
Ethernet ports .........................41
Ethernet connectors ......................42
Integrated system management ports ................42
Appendix. Notices .......................43
Edition notice .........................43
Trademarks ..........................44
Important notes.........................44
Electronic emission notices ....................45
Federal Communications Commission (FCC) statement .........45
Industry Canada Class A emission compliance statement ........46
Australia and New Zealand Class A statement ............46
United Kingdom telecommunications safety requirement.........46
European Union EMC Directive conformance statement.........46
Taiwan electrical emission statement ................46
Japanese Voluntary Control Council for Interference (VCCI) statement . . . 47
Power cords ..........................47
Index ............................49
iv IBM xSeries 345 Type 8670: Option Installation Guide

Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalacítohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d’installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
© Copyright IBM Corp. 2002 v

Antes de instalar este producto, lea la información de seguridad.
Lässäkerhetsinformationen innan du installerar den här produkten.
vi IBM xSeries 345 Type 8670: Option Installation Guide

Statement 1
Danger
Electrical current from power, telephone, and communication cables is hazardous.
To avoid a shock hazard:
vDo not connect or disconnect any cables or perform installation, maintenance, or
reconfiguration of this product during an electrical storm.
vConnect all power cords to a properly wired and grounded electrical outlet.
vConnect to properly wired outlets any equipment that will be attached to this
product.
vWhen possible, use one hand only to connect or disconnect signal cables.
vNever turn on any equipment when there is evidence of fire, water, or structural
damage.
vDisconnect the attached power cords, telecommunications systems, networks, and
modems before you open the device covers, unless instructed otherwise in the
installation and configuration procedures.
vConnect and disconnect cables as described in the following table when installing,
moving, or opening covers on this product or attached devices.
To connect:
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
To disconnect:
1. Turn everything OFF.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
Statement 2
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has a
module containing a lithium battery, replace it only with the same module type made
by the same manufacturer. The battery contains lithium and can explode if not
properly used, handled, or disposed of.
Do not:
vThrow or immerse into water.
vHeat to more than 100° C (212° F)
vRepair or disassemble
Dispose of the battery as required by local ordinances or regulations.
Safety vii

Statement 3
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
vDo not remove the covers. Removing the covers of the laser product could result in
exposure to hazardous laser radiation. There are no serviceable parts inside the
device.
vUse of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
Danger
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the
following. Laser radiation when open. Do not stare into the beam, do not view directly with
optical instruments, and avoid direct exposure to the beam.
Statement 4
≥18 kg (39.7 lb) ≥32 kg (70.5 lb) ≥55 kg (121.2 lb)
CAUTION:
Use safe practices when lifting.
Statement 5
CAUTION:
The power-control button on the device and the power switch on the power supply do
not turn off the electrical current supplied to the device. The device also might have
more than one power cord. To remove all electrical current from the device, ensure
that all power cords are disconnected from the power source.
1
2
viii IBM xSeries 345 Type 8670: Option Installation Guide

Statement 8
CAUTION:
Never remove the cover on a power supply or any part that has the following label
attached.
Hazardous voltage, current, and energy levels are present inside any component that
has this label attached. There are no serviceable parts inside these components. If you
suspect a problem with one of these parts, contact a service technician.
Statement 12:
CAUTION:
The following label indicates a hot surface nearby.
Statement 13
DANGER:
Overloading a branch circuit is potentially a fire hazard and a shock hazard under
certain conditions. To avoid these hazards, ensure that your system electrical
requirements do not exceed the branch circuit protection requirements. Refer to the
information that is provided with your IBM device for electrical specifications.
Statement 14
CAUTION:
Hazardous voltage, current, and energy levels might be present. Only a qualified
service technician is authorized to remove the covers where the following label is
attached.
Safety ix

Statement 15
CAUTION:
Make sure that the rack is secured properly to avoid tipping when the server unit is
extended.
Statement 16
CAUTION:
Some accessory or option board outputs exceed Class 2 or limited power source
limits and must be installed with appropriate interconnecting cabling in accordance
with the national electric code.
Statement 17
CAUTION:
The following label indicates moving parts nearby.
xIBM xSeries 345 Type 8670: Option Installation Guide

Chapter 1. Introduction
This Option Installation Guide provides the instructions to install, remove, and
connect optional devices that are supported by your server.
In addition to this Option Installation Guide, the following xSeries
™
345 Type 8670
documentation is provided with your server:
vInstallation Guide
This printed publication contains setup and installation instructions.
vRack Installation Instructions
This printed publication contains the instructions to install your server in a rack.
vSafety Book
This multilingual publication is provided in Portable Document Format (PDF) on
the IBM
®
xSeries Documentation CD. It contains translated versions of the
caution and danger statements that appear in the documentation for your server.
Each caution and danger statement has an assigned number, which you can use
to locate the corresponding statement in your native language.
vUser’s Guide
This publication is provided in PDF on the IBM xSeries Documentation CD. It
contains general information about your server.
vHardware Maintenance Manual and Troubleshooting Guide
This publication is provided in PDF on the IBM xSeries Documentation CD. It
contains the information to help you solve a problem yourself or to provide
helpful information to a service technician.
Notices and statements in this book
The caution and danger statements used in this book also appear in the multilingual
Safety Information book provided on the IBM xSeries Documentation CD. Each
caution and danger statement is numbered for easy reference to the corresponding
statements in the safety book.
The following types of notices and statements are used in this book:
vNote: These notices provide important tips, guidance, or advice.
vImportant: These notices provide information or advice that might help you avoid
inconvenient or problem situations.
vAttention: These notices indicate possible damage to programs, devices, or
data. An attention notice is placed just before the instruction or situation in which
damage could occur.
vCaution: These statements indicate situations that can be potentially hazardous
to you. A caution statement is placed just before the description of a potentially
hazardous procedure step or situation.
vDanger: These statements indicate situations that can be potentially lethal or
extremely hazardous to you. A danger statement is placed just before the
description of a potentially lethal or extremely hazardous procedure step or
situation.
© Copyright IBM Corp. 2002 1

Major components of the xSeries 345 Type 8670 server
The orange color on components and labels in your server identifies hot-swap or
hot-plug components. You can install or remove hot-swap or hot-plug components
while the system is running, provided that your system is configured to support this
function. For complete information about installing or removing a hot-swap or
hot-plug component, see the detailed information in Chapter 2, “Installing options”
on page 9.
The blue color on components and labels indicates touch points where a
component can be gripped, a latch moved, and so on.
The following illustration shows the major components in your server.
Note: The illustrations in this document might differ slightly from your hardware.
Hot-swap fan
Air baffle
Microprocessor
Microprocessor
air baffle
PCI riser card
assembly
Memory module
System board
VRM
Filler panel for
drive bay
Hot-swap
power supply
Heat sink
Power supply
blank (some models)
CPU CPU
VRM VRM
MEMORYMEMORY
DASD DASD
NMI NMI
SP SP FAN
FAN
POWER
SUPPLIES
POWER
SUPPLIES
PCI
BUS
PCI
BUS
2
A
B
C
1
NON
REDUNDANT
NON
REDUNDANT
CPU/VRM
MISMATCH
CPU/VRM
MISMATCH
OVERSPEC OVERSPEC
TEMP TEMP
REMIND REMIND
LightPath
Diagnostics™
Light Path
Diagnostics™
Shuttle
2IBM xSeries 345 Type 8670: Option Installation Guide

Component locations
This section provides illustrations of the system-board and PCI riser-card
component locations.
System-board option connectors
The following illustration shows the location of the system-board connectors for
user-installable options.
PCI-X slot 2
64-bit 3.3V
100 MHz
(J13)
PCI-X slot 1
64-bit 3.3V
100 MHz
(J14)
PCI riser
card
(J16)
DIMM 1
(J1) DIMM 3
(J3)
DIMM 4
(J4) VRM 2
(J5)
VRM 1
(J8)
DIMM 2
(J2)
Microprocessor 2
(J6)
Microprocessor 1
(J7)
Battery
(BH1)
PCI riser-card option connectors
The following illustration shows the location of the PCI riser-card connectors for
user-installable options.
PCI-X slot 3 64-bit
3.3V (PCI 3)133 MHz
PCI-X slot 4 64-bit
3.3V 133 MHz (PCI 4)
PCI slot 5 32-bit
5V 33 MHz (PCI 5)
System management connector
Chapter 1. Introduction 3

System-board internal cable connectors
The following illustration shows the internal cable connectors on the system board.
Fans 4 and 8
(J28)
Fans 3 and 7
(J27)
Fans 2 and 6
(J29)
Fans 1 and 5
(J26)
Power
(J24)
USB 3
operator panel
Internal SCSI
(J23) IDE (J21) Operator panel
(J22)
Power signal
(J25)
4IBM xSeries 345 Type 8670: Option Installation Guide

System-board external port connectors
The following illustration shows the location of the input/output external port
connectors on the system board.
Serial/video
(J9)
Mouse/keyboard
(J10)
Ethernet 1
(J11)
Ethernet 2
(J12)
USB 1
(J17)
USB 2
(J18)
External
SCSI
(J19)
RS485-A and B
(J15)
Chapter 1. Introduction 5

System-board switches and jumpers
The following illustration shows the location of the switch block (SW2) and the flash
boot jumper on the system board.
Flash boot block
recovery jumper
(J34)
System board
switch block
(SW2)
8 7 6 5 4 3 2 1
SW2
ON
6IBM xSeries 345 Type 8670: Option Installation Guide

Table 1 describes the function of each switch on the switch block.
Table 1. Switches 1-8
Switch
number Default value Switch description
8 Off Reserved.
7 Off Reserved.
6 Off Reserved.
5 Off Reserved.
4 Off Reserved.
3 Off Power-on override. When toggled to On, this switch forces the power on, overriding
the power-on button.
2 Off Power-on password override. Changing the position of this switch bypasses the
power-on password check the next time the server is turned on and starts the
Configuration/Setup Utility program so that you can change or delete the power-on
password. You do not need to move the switch back to the default position after the
password is overridden.
Changing the position of this switch does not affect the administrator password check
if an administrator password is set.
See the User’s Guide on the IBM xSeries Documentation CD for additional
information about the power-on password.
1 Off H8 out serial port. This switch is reserved for service use only.
Notes:
1. Before changing any switch settings or moving any jumpers, turn off the server;
then, disconnect all power cords and external cables. (Review the information in
“Safety”on page v, “Installation guidelines”on page 9, “Handling static-sensitive
devices”on page 10, and “Turning off the server”on page 12.)
2. Any system-board switch or jumper blocks that are not shown in the illustrations
in this book are reserved.
Chapter 1. Introduction 7

System-board LED locations
The following illustration shows the location of the LEDs on the system board. You
might need to refer to this illustration when solving problems with the server.
DIMM 1 error LED
(CR12)
DIMM 2 error LED
(CR15)
Integrated System Management
Processor (ISMP) activity
LED (CR41)
DIMM 3 error LED
(CR14)
DIMM 4 error LED
(CR13)
Microprocessor 2
error LED (CR17)
Microprocessor 1
error LED (CR18)
VRM 2 error LED
(CR16)
VRM 1 error LED
(CR19)
8IBM xSeries 345 Type 8670: Option Installation Guide