IBM 5280 User manual

GA21-9365-2
S5280-00
IBM 5280
Distributed Data
System
User 's Setup Procedures

-~- -
----
-- ---
- ----
- ~ ----
--- ---
-----
____ 9_
GA21-9365-2
S5280-00
IBM 5280
Distributed Data
System
User's Setup Procedures

Third Edition (July 1982)
This is a major revision of, and obsoletes, GA 21-9365-1. Changes are periodically made
to the information herein; these changes will be reported in technical newsletters or
in new editions of this publication.
Use this publication onlv for the purpose stated in the Preface.
This material might contain reference to, or information about, IBM products (machines
and programs), programming,
or services that are not announced in your country. Such
references or information must not be construed to mean that IBM intends to announce
such
IBM products, programming, or services in your country.
Publications are not stocked at the address below. Requests for copies of IBM publica-
tions and
for technical information about the system should be made to your IBM
representative or to the branch office serving your locality.
This publication could contain inaccuracies or typographical errors. Use the Reader's
Comment Form
at the back of this publication to make comments about this publication.
If the form has been removed, address your comments to IBM Corporation,
Information Design and Development, Dept. 997, 11400 Burnet Road, Austin, Texas
78758.
IBM may use and distribute any of the information you supply in any way
it believes appropriate without incurring any obligation whatever. You may, of course,
continue to use the information you supply.
© Copyright international Business Machines Corporation 1980, 1981, 1982

Use this publication only for the purpose of setting up the
IBM 5280 System.
This manual is divided into ten sections. Section 1
provides information about
what should have been done
prior
to set,up. Sections 2 through 6 provide procedures
for setting up the IBM 5281,5282,5286,5285, and 5288
respectively.
Section 7 provides the procedures
for labeling the
system. Section 8 provides a procedure
for running the
verification program. The program checks the devices
after you have set them up. Section 9 presents the
procedures
for connecting the communications lines to
the IBM 5280'system; Section 10 provides general
instructions
for disconnecting and relocating your system.
Preface
The tabs on the side of the manual indicate the name of
the procedure in each section.
This manual should be used after your devices are
unpacked and placed where you intend
to use them.
When you have finished setting up and verifying the IBM
5280 system,
save one of the User's Setup Procedures
manuals by placing it in the Machine Verificatio(1 binder.
Preface iii

This page is intentionally left blank.
iv

SECTION 1. WHAT MUST BE DONE PR lOR TO SETUP ................. 1
SOME IMPORTANT POINTS TO REMEMBER ABOUT SETUP ............ 2
SECTION 2. IBM 5281 SETUP PROCEDURE ......•................. 5
SECTION 3. IBM 5282 SETUP PROCEDURE •..............•....... 17
SECTION 4. IBM 5286 SETUP PROCEDURE ....................... 31
SECTION 5. IBM 5285 SETUP PROCEDURE .........•....•......•. 45
SECTION 6. IBM 5288 SETUP PROCEDURE ....................... 65
SECTION 7. LABELING YOUR SYSTEM ........................ , 87
LABELING THE DISKETTE DRIVES ........................... 88
LABELING THE PRINTER .................................. 92
SECTION 8. VERIFICATION PROCEDURE ....................... 95
BASIC OPERATIONAL INFORMATION. . . . . . . . . . . . . . . . . . . . . . . .. 96
Keyboards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 96
Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 97
Diskettes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.. 99
Diskette Drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
SYSTEM
CHECKOUT PROCEDURE ............................ 102
Diskette 1 Drive System Checkout Procedure ..................... 114
Diskette
20 Drive System Checkout Procedure .................... 117
Printer Test Pattern
...................................... 125
SECTION 9. COMMUNICATIONS LINE CONNECTION ............... 147
DDSACommunications Line ................................ 148
Local
DDSA Communications Line ........................... 148
1200 bps Integrated Nonswitched (38LS) Communications Line ........ 149
1200 bps Integrated Switched Communications Line ............... 149
1200 bps Integrated Nonswitched/Switched Communications Line ...... 150
SECTION 10. DISCONNECTING
AND RELOCATING
YOUR SYSTEM .......................................... 157
Contents
Contents v

This page is intentionally left blank.
vi

Section 1. What Must Be Done Prior to Setup
Before you start to set up your system, the following must have been
completed (as defined in
the Planning and Site Preparation Guide):
• Installed grounded outlets
• Completed system setup form and floor plan
• Labeled system cables and placed them where they will be connected to the
devices
• Assigned physical addresses to the printers and diskette drives (on the
setup form)
• Assigned a number to each keyboard (on the setup form)
• Placed each device where it will be set up
• Labeled the printer cables, if you have any printers
• If you have communications, the following must also have been completed:
Installed communications equipment
Completed a procedure
for establishing communications with your host
system
If these activities have not been completed, ask your supervisor to see the IBM
5280 System Planning and Site Preparation Guide, GA21-9351.
During the setup procedure you will be:
• Connecting cables
• Setting switches
• Labeling your system devices
• Inserting diskettes
• Loading programs
• Operating the keyboard
• Responding to system prompts
User's Setup Procedures

2
SOME IMPORTANT POINTS TO REMEMBER ABOUT SETUP
• Do not skip from page to page or from section to section looking for
information. All the information you need to set up a device is in a section
designated
for that device.
• Do not attempt to set up more than one device at a time, even though they
look alike. Return to the beginning of each section for like devices.
• When you start a section, read each step slowly and carefully. Be sure that
you understand each step before completing it. It is unlikely that you will
encounter any problems; but if you do, contact your supervisor.
• The cables and cable connectors are durable, but can be damaged if thrown
or stepped on.
• Before you begin asetup procedure, look at the machine number on the
device. The machine number
is always your starting point. Find the
machine number in this manual
by looking at the Contents page or by
looking at the page edge tab. The locations of the machine numbers
and
page edge tabs are shown in the following diagrams.
Machine Number
(5281 or 5285)
Contents
Page
(machine number)
Machine
Number
(5282 or 5286)
Or
Machine Number
(5288)

When you begin the setup procedure for your system, it is very important
that you set up the devices in the following order:
1. Auxiliary devices (set up IBM 5281s first and IBM 5282s second).
2. Printer: If you have a printer(s), see the printer customer setup manual,
Do not connect the prin~er cable(s). The printer cable(s) will be
connected using this manual.
3. Controller (IBM 5286, 5285, or 5288).
Caution: An IBM device can weigh up to 90 kilograms (200 pounds).
NEVER LIFT A DEVICE BY YOURSELF.
User's Setup Procedures 3