ICI 840121412876 Quick start guide

Alumilite Steps
part# 840121412876
DIRECTIONS FOR INSTALLATION & USE
2010-2021 TOYOTA 4RUNNER
(excludes models: 2010-2013 SR5, 2010-2021
Limited, 2019-2021
Nightshade edition, or any models with lower
cladding/lower rocker panel extensions)
For technical support,
call 1-800-626-8746 or email [email protected]
visit icionline.com to download instructions
WARNING: FAILURE TO COMPLY WITH INSTALLATION,
SAFETY, AND PRODUCT USE INSTRUCTIONS MAY RESULT IN
SERIOUS BODILY INJURY OR DEATH.
IMPORTANT NOTES
The contents of this installation and operation manual should be
read and comprehended before initializing the installment of the
above listed product. This will help minimize risk to injury through
the installation process and through the operation of the product.
TABLE OF CONTENTS
SAFETY, WARNINGS, AND OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02
2. PARTS AND TOOLS REQUIRED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03
3.
ICI STEP INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . 04-07
4.
SOCIAL MEDIA REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .07
1.

SAFETY, WARNINGS, AND OPERATION
•Please ensure that the installer and end-user of this product have
familiarized themselves with the contents in this manual. This
manual provides important information about the possible safety
and operation risks that are involved with the usage of this
product.
•Our number one concern is the safety of our customers. This
product is intended to be installed by a professional to minimize
risk of an improper installation. Improper installations can lead to
product damage, vehicle damage, and bodily injury. We ask that
you reach out for professional assistance if this installation is
beyond your capabilities.
•Please ensure to safeguard this installation and operation manual
to reference in the future or to pass on to a future owner of the
product.
•Please follow all instructions and take all safety precautions
necessary throughout the entirety of the installation process.
SYMBOL DESCRIPTION
HAZARDOUS WARNING
WARNING: SHARP ELEMENTS
WARNING: CRUSHING OF HANDS
WARNING: HOT SURFACE
MANDATORY: WEAR EYE PROTECTION
PARTS AND TOOLS REQUIRED
TOOL DESCRIPTION
RATCHET/SOCKET
WRENCH
SOCKETS : 13mm
(12mm for OE
hardware)
13mm
(Allen wrench
included)
EYE PROTECTION
13
PARTS AND TOOLS REQUIRED
02 03
Front:
Rear:
Hardware Kit includes:
(1). Qty x 16 = M8 x 35mm Hex
Countersunk Bolts
(2). Qty x 16 = M8 Finish Washers
(3). Qty x 12 = M8-1.25 x 20mm Hex
Head Bolts
(4). Qty x 28 = M8 Flat Washers
(5). Qty x 16 = M8-1.25 Nylock Nuts
(6). Allen Wrench included
Components List:
(a). Side Bars - Qty x 2
1 Driver / 1 Passenger (100525)
(b). Front Brackets - Qty x 2
1 Driver / 1 Passenger (100527)
(c). Middle/Rear Brackets - Qty x 4
2 Driver / 2 Passenger (100528)
(d). Hoop Steps (bolt on) - Qty x 4
2 Driver / 2 Passenger (100524)
Reference Diagram:
DRIVER SIDE example below:

ICI STEP INSTALLATION
Step 1 (Prep)
Beginning on the Driver's side,
remove any steps if equipped.
Next, locate the 3 sets of
mounting points on the
underside of the vehicle (Fig. 1).
Please note that your vehicle
may have tape, plugs, and/or
factory bolts covering up the
mounting locations. These will
need to be removed so that the
mounting locations can be
accessed. Keep any OE
hardware to reuse during
installation.
ICI STEP INSTALLATION
Figure 1.
Step 3 (Hang bar
on Brackets)
Next, locate the driver side bar
(100525), the distance from the
front of the bar to the first step
hoop is greater than the
distance from the rear of the
bar to the second step hoop,
reference the diagram on page
3. The top of the bar has a
small lip, use the lip to hang the
bar on the brackets. This will
make the installation process
easier and hands-free. Figure 6.
Figure 5.
04 05
Figure 2.
Step 2
(Install Brackets to
4Runner)
Begin with the driver front
bracket 100527. Use (2 sets) of
M8x20mm hex bolts and flat
washers unless you are reusing
the OE bolts. Use a 13mm
socket or 12mm for the OE bolts
and do not fully tighten yet.
Once the front bracket is
attached, move on to the middle
bracket, then the rear bracket,
repeating the steps above.
Figure 4.
Figure 3.
Step 4 (Bolt Middle
Bracket to Bar)
Start by bolting the middle
bracket (100528) to the bar.
Use (2 sets) of M8xM35mm
hex countersunk bolts, finish
washers, flat washers, and
nylock nuts. Use a 13mm
wrench and the provided Allen
wrench. Do not fully tighten
until all brackets and steps
have been attached.
Step 5 (Bolt Bar to
Front Bracket and
Hoop Step)
Next, bolt the bar to the front
bracket (100527) and hoop step
(100524). Use (2 sets) of
M8x35mm hex countersunk
bolts, finish washers, flat
washers, and nylock nuts. Use a
13mm wrench and the provided
Allen wrench. Do not fully
tighten until all brackets and
steps have been attached. See
the diagram on page 3 for
reference. Step 6 (Finish Front
Hoop Step)
Once the front bracket (100527)
and hoop step (100524) is
bolted to the bar, use (1 set) of
M8x35mm hex countersunk
bolts, finish washers, flat
washers, and nylock nuts to
finish bolting the hoop step to
the bar. Do not fully tighten
until all brackets and steps have
been attached. See diagram on
page 3 for reference.

ICI STEP INSTALLATION
STEP 8 (Tighten
Brackets to
4Runner)
Make sure all 3 brackets, the
bar, and the 2 hoops steps are
loosely fitted to each other
and to the vehicle. Using a 12
or 13mm socket, fully tighten
the front bracket to the
vehicle, make sure the bracket
is flush with the mounting
surface. Repeat on the middle
and rear bracket checking the
bracket alignment as needed.
STEP 9 (Tighten
Brackets to the Bar
and Hoop-Steps)
Now, adjust the bar from
front to back and tighten the
bar to the brackets with a
13mm socket and provided
Allen. Make sure the bar is
flush with the front and
bottom face of the brackets
as you are tightening them.
06
Figure 9.
07
STEP 7 (Bolt Bar to
Rear Bracket and
Hoop Step)
Repeat steps 5 and 6 for the
rear bracket and hoop step.
As shown in Figure 7, the rear
bracket and hoop step share a
bolt in the very rear. See the
diagram on page 3 for
reference.
ICI STEP INSTALLATION
www.facebook.com/InnovativeCreationsInd
www.instagram.com/ici_usa Hashtags:
#ICIUSA
#ICIAlumilite
#AlumiliteSteps
#AlumiliteBumpers
Figure 7.
Figure 8.
Figure 10.
STEP 10 (Finish)
Check all hardware and
make sure they are fully
tightened. Reference
diagram on page 3 for
hardware locations. Repeat
Steps 1-10 for the Passenger
Side.
*PRO TIP: When tightening the Finish Washers, hold the Allen Key tight so the Bolt does not spin.
Then, tighten the Nut on the backside.
This will prevent the Bolt and Finish Washer from spoinning and scratching the Bar.
AMAZING!
You have successfully completed the
installation of your new Alumilite steps.
Time to flex on your friends through
Social Media! Don't forget to Tag us!
Drop us a Review!