ICI 840121412968 Quick start guide

WARNING: FAILURE TO COMPLY WITH INSTALLATION,
SAFETY, AND PRODUCT USE INSTRUCTIONS MAY RESULT IN
SERIOUS BODILY INJURY OR DEATH.
IMPORTANT NOTES
The contents of this installation and operation manual should be
read and comprehended before initializing the installment of the
above listed product. This will help minimize risk to injury through
the installation process and through the operation of the product.
TABLE OF CONTENTS
SAFETY, WARNINGS, AND OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02
2. PARTS AND TOOLS REQUIRED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03
3.
ICI STEP INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . 04-06
4.
SOCIAL MEDIA REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .07
1.
Alumilite Steps
part# 840121412968
DIRECTIONS FOR INSTALLATION & USE
2015-2021 FORD F150, 2017-2021 FORD
RAPTOR, AND 2017-2021 FORD SUPERDUTY
CREW CAB (FULL 4-DOOR)
For technical support,
call 1-800-626-8746 or email [email protected]
visit icionline.com to download instructions

SAFETY, WARNINGS, AND OPERATION
•Please ensure that the installer and end-user of this product have
familiarized themselves with the contents in this manual. This
manual provides important information about the possible safety
and operation risks that are involved with the usage of this
product.
•Our number one concern is the safety of our customers. This
product is intended to be installed by a professional to minimize
risk of an improper installation. Improper installations can lead to
product damage, vehicle damage, and bodily injury. We ask that
you reach out for professional assistance if this installation is
beyond your capabilities.
•Please ensure to safeguard this installation and operation manual
to reference in the future or to pass on to a future owner of the
product.
•Please follow all instructions and take all safety precautions
necessary throughout the entirety of the installation process.
SYMBOL DESCRIPTION
HAZARDOUS WARNING
WARNING: SHARP ELEMENTS
WARNING: CRUSHING OF HANDS
WARNING: HOT SURFACE
MANDATORY: WEAR EYE PROTECTION
PARTS AND TOOLS REQUIRED
TOOL DESCRIPTION
RATCHET/SOCKET
WRENCH
SOCKETS : 13mm
13mm
(Allen wrench
included)
EYE PROTECTION
13
PARTS AND TOOLS REQUIRED
02
Front:
Rear:
Hardware Kit includes:
(1). Qty x 16 = M8 x 35mm Hex
Countersunk Head Bolts
(2). Qty x 16 = M8 Finish Washers
(3). Qty x 34 = M8 Nylock Nuts
(4). Qty x 34 = M8 x 24 x 2mm Flat
Washers
(5). Qty x 18 = M8 Plastic
Retainers
(7). Allen Wrench included
Components List:
(a). Side Bars - Qty x 2
1 Driver / 1 Passenger
(b). Front/Middle/Rear Brackets
- Qty x 6
3 Driver /3 Passenger (100540)
(c). Hoop Steps (bolt on) - Qty x 4
2 Driver / 2 Passenger (100524)
Reference Diagram:
DRIVER SIDE example below:
03

ICI STEP INSTALLATION
Step 1 (Prep)
Beginning on the Driver's side,
remove any steps if equipped.
Next, locate the 3 sets of
mounting points on the
underside of the vehicle (Fig. 1).
Underneath the rocker panel,
there are three bracket
locations, each location has
three OE Factory bolts
protruding out.
ICI STEP INSTALLATION
Figure 1.
Step 3 (Hang bar
on Brackets)
Next, locate the driver side bar.
The front tip of each bar is
sloped down to follow curve of
door. Reference diagram on
page 3. The top of the bar has
a small lip, use the lip to hang
the bar on the brackets. This
will make the installation
process easier and hands-free.
Figure 6.
Figure 5.
04 05
Figure 2.
Step 2 (Install
Brackets to Truck)
Begin with the driver front bracket
100540. You will need (3 sets) of
M8 nylock nuts and M8 flat
washers. Use a 13mm socket and
do not fully tighten yet. Once the
front bracket is attached, move
on to the middle and rear
brackets, repeating the steps
above for each bracket.
Figure 4.
Figure 3.
Step 4 (Bolt Front
Bracket to Bar)
Start by bolting the front
bracket to the bar. It is the 1st
bolt hole from the front. You
will need (2 sets) of M8 nylock
nuts, M8x35mm hex
countersunk bolts, M8 flat
washers, and M8 finish
washers. Use a 13mm wrench
and the provided Allen
wrench. Do not fully tighten
until all brackets and steps
have been attached.
Step 5 (Bolt Middle
Bracket to Bar and
Front Hoop Step)
Next, bolt the middle bracket to
the bar and front hoop step.
Note that the bracket and hoop
step share a bolt. You will need
(3 sets) of M8 nylock nuts,
M8x35mm hex countersunk
bolts, M8 flat washers, and M8
finish washers. Use a 13mm
wrench and the provided Allen
wrench. Reference diagram on
page 3. Do not fully tighten yet. Step 6 (Bolt Rear
Bracket to Bar and
Rear Hoop Step)
Then, bolt the rear bracket to
the bar and frear hoop step.
Note that the bracket and hoop
step share a bolt. You will need
(3 sets) of M8 nylock nuts,
M8x35mm hex countersunk
bolts, M8 flat washers, and M8
finish washers. Use a 13mm
wrench and the provided Allen
wrench. Reference diagram on
page 3. Do not fully tighten yet.

ICI STEP INSTALLATION
STEP 8 (Tighten
Brackets to the Bar)
Once the 3 brackets are fully
tightened to the truck, adjust
the bar from front to back and
tighten the bar to the brackets
with a 13mm socket and
provided Allen wrench. Make
sure the bar is flush with the
front and bottom face of the
brackets as you are tightening
them. Then, tighten the Hoop
Steps to the bar.
STEP 9 (Finish)
Check all hardware and
make sure they are fully
tightened. Reference
diagram on page 3 for
hardware locations. Repeat
Steps 1-9 for the Passenger
Side.
06
Figure 9.
07
STEP 7 (Tighten
Brackets to Truck)
Make sure all 3 brackets are
loosely fit to the vehicle and bar.
Using a 13mm socket, fully
tighten the front bracket to the
vehicle. Make sure the bracket is
flush with the mounting surface.
Repeat on the middle and rear
brackets, checking the bracket
alignment as needed. Leave bar
loose for now.
www.facebook.com/InnovativeCreationsInd
www.instagram.com/ici_usa Hashtags:
#ICIUSA
#ICIAlumilite
#AlumiliteSteps
#AlumiliteBumpers
Figure 7.
Figure 8.
TAG ICI ON SOCIAL MEDIA
*PRO TIP: When tightening the Finish Washers, hold the Allen Key tight so the Bolt does not spin.
Then, tighten the Nut on the backside.
This will prevent the Bolt and Finish Washer from spoinning and scratching the Bar.
AMAZING!
You have successfully completed the
installation of your new Alumilite steps.
Time to flex on your friends through
Social Media! Don't forget to Tag us!
Drop us a Review!