ICI 840121412883 Quick start guide

Alumilite Steps
part# 840121412883
DIRECTIONS FOR INSTALLATION & USE
2005-2021 TOYOTA TACOMA (full 4-door)
For technical support,
call 1-800-626-8746 or email [email protected]
visit icionline.com to download instructions
WARNING: FAILURE TO COMPLY WITH INSTALLATION,
SAFETY, AND PRODUCT USE INSTRUCTIONS MAY RESULT IN
SERIOUS BODILY INJURY OR DEATH.
IMPORTANT NOTES
The contents of this installation and operation manual should be
read and comprehended before initializing the installment of the
above listed product. This will help minimize risk to injury through
the installation process and through the operation of the product.
TABLE OF CONTENTS
SAFETY, WARNINGS, AND OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02
2. PARTS AND TOOLS REQUIRED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03
3.
ICI STEP INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . 04-06
4.
SOCIAL MEDIA REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .07
1.

SAFETY, WARNINGS, AND OPERATION
•Please ensure that the installer and end-user of this product have
familiarized themselves with the contents in this manual. This
manual provides important information about the possible safety
and operation risks that are involved with the usage of this
product.
•Our number one concern is the safety of our customers. This
product is intended to be installed by a professional to minimize
risk of an improper installation. Improper installations can lead to
product damage, vehicle damage, and bodily injury. We ask that
you reach out for professional assistance if this installation is
beyond your capabilities.
•Please ensure to safeguard this installation and operation manual
to reference in the future or to pass on to a future owner of the
product.
•Please follow all instructions and take all safety precautions
necessary throughout the entirety of the installation process.
SYMBOL DESCRIPTION
HAZARDOUS WARNING
WARNING: SHARP ELEMENTS
WARNING: CRUSHING OF HANDS
WARNING: HOT SURFACE
MANDATORY: WEAR EYE PROTECTION
PARTS AND TOOLS REQUIRED
TOOL DESCRIPTION
RATCHET/SOCKET
WRENCH
SOCKETS : 13mm
13mm
(Allen wrench
included)
EYE PROTECTION
13
PARTS AND TOOLS REQUIRED
02 03
Front:
Rear:
Hardware Kit includes:
(1). Qty x 20 = M8 Nylock Nuts
(2). Qty x 12 = M8 x 30mm Hex
Head Bolts
(3). Qty x 20 = M8 x 35mm Hex
Countersunk Bolts
(4). Qty x 32 = M8 x 24 x 2mm Flat
Washers
(5). Qty x 12 = M8 lock Washers
(6). Qty x 20 = M8 Finish Washers
(7). Allen Wrench included
Components List:
(a). Side Bars - Qty x 2
1 Driver / 1 Passenger
(b). Front Brackets - Qty x 2
1 Driver / 1 Passenger (100532)
(c). Middle/Rear Brackets - Qty x 4
2 Driver / 2 Passenger (100533)
(d). Hoop Steps (bolt on) - Qty x 4
2 Driver / 2 Passenger (100524)
Reference Diagram:
DRIVER SIDE example below:

ICI STEP INSTALLATION
Step 1 (Prep)
Beginning on the Driver's side,
remove any steps if equipped.
Next, locate the 3 sets of
mounting points on the
underside of the vehicle (Fig. 1).
Please note that your vehicle
may have factory OE plastic
bolts covering up the mounting
locations. These will need to be
removed so that the mounting
locations can be accessed.
ICI STEP INSTALLATION
Figure 1.
Step 3 (Hang bar
on Brackets)
Next, locate the driver side bar.
The front half of the bar has
four bolt holes while the rear
half of the bar has three bolt
holes, reference figure 3. The
top of the bar has a small lip,
use the lip to hang the bar on
the brackets. This will make the
installation process easier and
hands-free.
Figure 6.
Figure 5.
04 05
Figure 2.
Step 2 (Install
Brackets to Tacoma)
Begin with the driver front bracket
100532. Use (2 sets) of M8x30mm
hex bolts, M8 flat washers, and
M8 lock washers. Use a 13mm
socket and do not fully tighten
yet. Once the front bracket is
attached, move on to the middle
and rear brackets (100533),
repeating the steps above for
each bracket.
Figure 4.
Figure 3.
Step 4 (Bolt Middle
Bracket to Bar)
Start by bolting the middle
bracket (100533) to the bar.
Use (2 sets) of M8 nylock nuts,
M8x35mm hex countersunk
bolts, M8 flat washers, and
M8 finish washers. Use a
13mm wrench and the
provided Allen wrench. Do
not fully tighten until all
brackets and steps have been
attached.
Step 5 (Bolt Bar to
Front Bracket and
Rear Bracket)
Next, bolt the bar to the front
bracket (100532). Do not fully
tighten yet. Use (2 sets) of M8
nylock nuts, M8x35mm hex
countersunk bolts, M8 flat
washers, and M8 finish
washers. Use a 13mm wrench
and the provided Allen
wrench. Repeat the steps
above for the rear bracket
(100533) See the diagram on
page 3 for reference. Step 6 (Bolt Front
and Rear Hoop
Steps to bar)
After the brackets have been
attached to the bar, bolt the
front and rear hoop step to the
bar. For each hoop step, use (2
sets) of M8 nylock nuts,
M8x35mm hex countersunk
bolts, M8 flat washers, and M8
finish washers. Use a 13mm
wrench and the provided Allen
wrench. Leave loosely fitted for
now.

ICI STEP INSTALLATION
STEP 8 (Tighten
Brackets to the Bar)
Once the 3 brackets are fully
tightened to the truck, adjust
the bar from front to back and
tighten the bar to the brackets
with a 13mm socket and
provided Allen wrench. Make
sure the bar is flush with the
front and bottom face of the
brackets as you are tightening
them. Then, tighten the Hoop
Steps to the bar.
STEP 9 (Finish)
Check all hardware and
make sure they are fully
tightened. Reference
diagram on page 3 for
hardware locations. Repeat
Steps 1-9 for the Passenger
Side.
06
Figure 9.
07
STEP 7 (Tighten
Brackets to Truck)
Make sure all 3 brackets are
loosley fit to the vehicle and
bar. Using a 13mm socket, fully
tighten the front bracket to the
vehicle. Make sure the bracket
is flush with the mounting
surface. Repeat on the middle
and rear bracket checking the
bracket alignment as needed.
Leave bar loose for now.
www.facebook.com/InnovativeCreationsInd
www.instagram.com/ici_usa Hashtags:
#ICIUSA
#ICIAlumilite
#AlumiliteSteps
#AlumiliteBumpers
Figure 7.
Figure 8.
TAG ICI ON SOCIAL MEDIA
*PRO TIP: When tightening the Finish Washers, hold the Allen Key tight so the Bolt does not spin.
Then, tighten the Nut on the backside.
This will prevent the Bolt and Finish Washer from spoinning and scratching the Bar.
AMAZING!
You have successfully completed the
installation of your new Alumilite steps.
Time to flex on your friends through
Social Media! Don't forget to Tag us!
Drop us a Review!