Icom IC-F3262D series User manual

–4 –
–1 –
Thank you for choosing the IC-F3262DT/IC-F3262DS
v h f dp m r h a n d h e l d t r a n s c e i v e r s or IC-F4262DT/
IC-F4262DS u h f dp m r h a n d h e l d t r a n s c e i v e r s .
READ ALL INSTRUCTIONS carefully and
completely before using your transceiver.
INSTRUCTIONS
VHF dPMR HANDHELD TRANSCEIVERS
Iç-F4262D series
UHF dPMR HANDHELD TRANSCEIVERS
Iç-F3262D series
A-7213D-1EU Printed in Japan
© 2015 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Battery pack Belt clip
Connector cover
(with screw)
Flexible antenna
(This illustration is
for the UHF type.)
SUPPLIED ACCESSORIES
This instruction sheet includes some functions which are
usable only when they are preset by your dealer. Ask your
dealer for details.
See the operating guide for details of the IDAS™
dPMR™ (digital Private Mobile Radio) and the BIIS
(Binary Interchange of Information and Signaling) 1200
system operations. Ask your dealer for details.
FOREWORD
Icom, Icom Inc. and Icom logo are registered trademarks of Icom
Incorporated (Japan) in Japan, the United States, the United Kingdom,
Germany, France, Spain, Russia, Australia, New Zealand, and/or other
countries.
IDAS and the IDAS logo are trademark of Icom Incorporated (Japan).
dPMR and the dPMR logo are trademarks of the dPMR MoU Association.
All other products or brands are registered trademarks or trademarks of their
respective holders.
FUNCTION DISPLAY
qSIGNAL STRENGTH ICON
Displays the relative receive signal strength.
wLOW POWER ICON
Displayed when low output power is selected.
 •Whenthebatterychargedecreasestoaspeciedlevel,low
power is automatically selected.
eSPEAKER/TELEPHONE ICON
Displayed when the channel is in the ‘audible’➥
(unmute) mode.
Displayed when a matched signal is received.➥
“➥” is displayed when connecting to a telephone line.
r SCRAMBLER ICON
Displayed when the Voice Scrambler function is ON.
t SCAN ICON
Displayed while scanning.
y MESSAGE ICON
Displayed when a received message (Short Data➥
Message or Status Message) is stored in the stack
memory.
Blinks when an unread message is in the stack➥
memory.
u BELL ICON
Displayed when a matched signal is received, depending
on the presetting.
i GPS/COMPANDER ICON
➥Displayed when the GPS receiver acquires the GPS
signal from a satellite and the GPS Indicator is set to
ON.
➥“ ” is displayed when the Compander function is
activated and the GPS Indicator is set to OFF.
o BATTERY ICON
Displays the battery level.
Indication
Battery level Full Mid Charging
required
Exhausted
Battery
blinks when the battery is over charged.
blinks when the battery is exhausted.
 •Thisiconmaynotbedisplayed,dependingonthepresetting.
!0 ALPHANUMERIC READOUT
➥Displays the operating channel number, channel
name, Menu contents, DTMF code, and so on.
➥Depending on the presetting, characters are displayed
in 1 line or 2 lines on the display.
 •Inthisinstructionmanual,thedisplayillustrationis
described as having characters displayed in 2 lines.
!1 KEY ICONS
Display the assigned function of the [P0], [P1], [P2] and
[P3] front panel keys.
001 ch-01
IC-F3262D
MENU
ENTBACK
PRIVATE
ID 0000002
dPMR CLRMENUCALL
0001
1234
CALL MONTXCEBIIS
CLR
CONTACT
ENTBACK
CONTACT
qwe rt y u i o
!0
!1
About the LED indicatorD
•Lightsredwhiletransmitting.
•Lightsgreenwhilereceivingasignal,orwhen
the squelch is open.
•Blinksredwhenthebatteryisexhausted.
About the Multi-connectorD
CAUTION: Attach the connector cover
when an optional accessory is not used.
PANEL DESCRIPTION
Turning power OND
Beforeusingthetransceiverforthersttime,thebattery
pack must be fully charged for optimum life and
operation. See the back page of this sheet.
Rotate [VOL] to turn ON the power.➥
NOTE:
•Ifthetransceiverisprogrammedforastartup
password, input the digit codes as directed by your
dealer.
•
The battery type must be selected, according to the
attached battery type, when tuning the transceiver ON.
See the operating guide for details of entering the
password or selecting the battery type.
BASIC OPERATION
Receiving and TransmittingD
Receiving:
Select a channel.q
Rotate [Rotary selector].➥
Push [CH Up] or [CH Down].➥
Push one of the direct channel select keys,➥
[MR-CH 1] to [MR-CH 4].
Whenreceivingacall,rotate[VOL]toadjusttheaudiow
output level to a comfortable listening level.
Transmitting:
CAUTION: Attach an antenna before transmitting.
Transmitting without an antenna may damage the
transceiver.
Waituntilthechanneliscleartoavoidinterference.
Whileholdingdown[PTT],speakatanormalvoicelevel.q
Release [PTT] to receive.w
IMPORTANT:
To maximize the readability of your signal:
1. After pushing [PTT], pause briefly before you start
speaking.
2. Hold the microphone 5 to 10 cm from your mouth, then
speak at a normal voice level.
*1A GPS receiver is bult-in, depending on the transceiver version.
*2Dealer assignable
Antenna
connector
[Rotary Selector]
[Emer]*
[Side1]*
[PTT]
[Side2]*
[Side3]*
10-keypad
[P0]*2, [P1]*2,
[P2]*2, [P3]*2
Function display
Microphone
Speaker
LED indicator
Multi-connector
[VOL]
GPS receiver*1
The illustration is of the 10-key type transceivers.

–2 – – 3 –
BATTERY CHARGING
Rapid charging with the BC-119N+AD-106D
You can rapidly charges the Li-ion battery pack with the
optional BC-119N.
Charging time: Approximately 3 hours for the BP-232H
The following items are additionally required.
•AD-106chargeradapter(purchaseseparately)
•Apoweradapter(maybesuppliedwithBC-119N,
depending on the charger version) or the OPC-515L/
CP-23L DC power cable.
Power adapter
(A different type, or no
power adapter is sup-
plied, depending on the
charger’s version.)
Optional OPC-515L* (for a
13.8 V power source) or
CP-23L (for a 12 V cigarette
lighter socket) can be used
instead of the power adapter.
CAUTION: NEVER connect the OPC-
515L to a power source using reverse
polarity. This will ruin the battery charger.
White line: Black line:
*
Battery
pack
AD-106 charger
adapter is installed
in the BC-119N.
Transceiver
Tu rn OFF
the power
Charging with the BC-160D
You can rapidly charge the Li-ion battery pack with the
BC-160.
•Charging time
Approximately3hoursfortheBP-232WP
The following items are additionally required:
•Apoweradapter(maybesuppliedwiththecharger,
depending on the charger version) or the OPC-515L/
CP-23L DC power cable.
Power adapter
(A different type, or no power adapter is supplied,
depending on the charger’s version.)
Battery
pack
Transceiver
Tu rn power
OFF
Optional OPC-515L* (for a
13.8 V power source) or
CP-23L (for a 12 V cigarette
lighter socket) can be used
instead of the power adapter.
CAUTION: NEVER
connect the OPC-
515L to a power
source using reverse
polarity. This will ruin
the battery charger.
White line:
Black line :
*
AD-106 installationD
You must install the AD-106 c h a r g e r a d a p t e r into the
BC-119N d e s k t o p c h a r g e r or BC-121N m u l t i -c h a r g e r
before charging any batteries.
q Connect the AD-106 and the BC-119N/BC-121N.
Install the AD-106 into the holder space of the BC-119N/w
BC-121N with the supplied screws.
Screws supplied
with the charger
adapter
AD-106
Plugs
Sockets
This illustration shows
the BC-119N.
Rapid charging with the BC-121N+AD-106D
You can charge up to 6 battery packs with the optional
BC-121N.
Charging time: Approximately 3 hours for the BP-232H
The following items are additionally required.
(purchase separately)
•SixAD-106chargeradapters
•BC-157SpoweradapterortheOPC-656DCpowercable
Transceiver
Battery
pack
AD-106 charger
adapters are installed
in each slot.
Tu rn OFF the power
OPC-656* DC power cable
Connect to a 13.8 V, 7 A (min.)
power supply
*Polarity of the OPC-656
Red line: Black line:
Power adapter
BATTERY PACKSD
• BP-232WP li-ion b at t e r y p a c k
Voltage: 7.4 V, Capacity: 2250 mAh (min.) 2300 mAh (typical)
Battery life: (Digital mode) Approximately 14.5 hours
(Analog mode) Approximately 13 hours
Whenthepowersavefunctionissetto“Short,”andtheoperating
periods are calculated under the following conditions:
TX:RX:standby = 5:5:90
• BP-240/BP-261 b at t e r y c a s e
BP-240: For AAA (LR03) ×6 alkaline
BP-261: For AA (LR6) ×6 alkaline
BP-240andBP-261haveIPX4waterproofprotection.Whenin
use, the transceiver’s waterproof rating meets IPX4.
DC CABLESD
• CP-23L c i g a r e t t e l i g h t e r c a b l e
Used when charging battery packs through a 12 V cigarette
lighter socket. For use with the BC-119N/BC-160 chargers.
• OPC-515L/OPC-656 d c p o w e r c a b l e s
Used when charging battery packs using a 13.8 V DC power
source instead of the power adapter.
OPC-515L: For the BC-119N/BC-160
OPC-656: For the BC-121N
CHARGERSD
• BC-119N d e s k t o p c h a r g e r + AD-106 c h a r g e r a d a p t e r
+ BC-145S p o w e r a d a p t e r
For rapidly charging of battery packs.
A power adapter may be supplied, depending on the charger’s version.
Charging time: Approximately3.5hoursfortheBP-232WP.
• BC-121N m u l t i -c h a r g e r + AD-106 c h a r g e r a d a p t e r (6 pcs.)
+ BC-157S p o w e r a d a p t e r
For rapidly charging of up to 6 battery packs simultaneously.
Six AD-106s are required.
A power adapter or a DC power source must be purchased separately.
Charging time: Approximately3.5hoursfortheBP-232WP.
• BC-160 d e s k t o p c h a r g e r + BC-145S p o w e r a d a p t e r
For rapidly charging of battery packs.
A power adapter may be supplied, depending on the charger’s version.
Charging time: Approximately3.5hoursfortheBP-232WP.
BELT CLIPSD
• MB-93 s w i v e l b e l t c l i p
• MB-94/MB-94R b e l t c l i p
Alligator-type belt clip.
• MB-96N/MB-96F l e a t h e r b e l t h a n g e r
ANTENNASD
• FA-SC56VS/FA-SC57VS/FA-SC73US s t u b b y a n t e n n a s
Shorter VHF or UHF antennas.
FA-SC56VS: 150–162 MHz FA-SC57VS: 160–174 MHz
FA-SC73US: 450–490 MHz
• FA-SC25V/FA-SC55V/FA-SC03U
FA-SC25U/FA-SC57U/FA-SC72U f l e x i b l e a n t e n n a s
VHF or UHF antennas.
FA-SC25V: 136–150 MHz FA-SC55V: 150–174 MHz
FA-SC03U: 380–430 MHz FA-SC25U: 400–430 MHz
FA-SC57U: 430–470 MHz FA-SC72U: 470–520 MHz
• FA-SC61VC/FA-SC61UC c u t a n t e n n a s
FA-SC61VC: 136–174 MHz FA-SC61UC: 380–520 MHz
• FA-SC62V/FA-SC63V h i g h g a i n a n t e n n a s
FA-SC62V: 150–160 MHz FA-SC63V: 155–165 MHz
OTHERSD
• AD-118 a c c a d a p t e r
Allows you to connect an accessory which uses a HIROSE
plug. See the instruction sheet of the AD-118 for details of the
recommended accessories.
CAUTION: The AD-118 does not have any waterproof
protection.Whenitisconnected,NEVERexposetheadaptor
and the transceiver to rain, snow or any liquids.
• HM-184/HM-184H s p e a k e r m i c r o p h o n e
Rugged type speaker microphone.
The HM-184 and HM-184H meet IP67 requirements for
waterproof protection.
• MB-130 v e h i c l e c h a r g e r b r a c k e t
Vehicle mounting bracket for the BC-160 battery charger.
OPTIONS
BATTERY CHARGING (Continued)
IMPORTANT: Battery charging caution
Ensure the guide tabs on the battery pack are correctly
aligned with the guide rails inside the charger adapter.
This illustration is for the BC-160.
CAUTION:
When using the OPC-656 DC power cable
NEVER reverse the polarity when connecting the
OPC-656 to a power source. This will ruin the battery
charger.
OPC-656: Red line: +,Black line: _
Approved Icom optional equipment is designed for optimal performance when
used with an Icom transceiver.
Icom is not responsible for the destruction or damage to an Icom transceiver in
the event the Icom transceiver is used with equipment that is not manufactured
or approved by Icom.
Some options may not be available in some countries. Please ask your dealer
for details.
Tabs
Guide rail