ICP DAS USA ET-2200 Series User manual

Technical support: servic[email protected] P1
ET-2268 Quick Start
v1.1, Mar. 2018
What’s in the box?
Related Information
The package includes the following items:
ET-2268 Module x 1
Quick Start x1
(This Document)
ET-2200 Series Product Page:
Documentation & Firmware:
NS-205/MDR-20-24 Product Page (optional):

Technical support: servic[email protected] P2
1
Connecting the Power and Host PC
1) Make sure your PC has workable network settings.
Disable or well configure your Windows firewall and Anti-Virus firewall first,
else the “Search Servers” on Chapter 5 may not work. (Please contact
with your system Administrator)
2) Connect both the ET-2268 and your PC to the same sub network or the
same Ethernet switch.
3) Supply power (+10~+30 VDC) to the ET-2268.
4) Verify that the “PWR”LED indicator
on the ET-2268 is flashing.
Red, OK

Technical support: servic[email protected] P3
2 Pin Assignments & Wiring Note
Pin Assignments:
Wire Connections:
Readback as 1 Readback as 0
Relay Output
Form A Relay
in NO1, NO3,
NO5, NO7
Form C Relay
in NO0, NO2,
NO4, NO6
NCx
COMx
NOx
AC/DC
Load1
Load2
NOx
COMx
Load
AC/DC
NOx
COMx
Load
AC/DC
NCx
COMx
NOx
AC/DC
Load1
Load2

Technical support: servic[email protected] P4
3 Wiring the DI and DO for Self-test
A tip for connecting the wire to the connector
A tip for removing the wire from the connector
1) Connect the External Power +24V to the NO0 pin (Pin01).
2) Connect the External Power GND to the COM0 pin (Pin03).
NO0 01
COM0 03

Technical support: servic[email protected] P5
4 Modbus Address
The nDO parameters in the following Modbus Address Tables are as follows:
Mode
Name
Universal
DIO
Number of DO channels
(nDO)
Number of DI channels
(nDI)
ET-2268
-
8
-
(0xxxx) DO address:
Begin
address
Points
Description
Bits
Per
Point
Range
Access
Type
0 (0x0)
1~nDO
Digital Output Channels
1
0: OFF, 1: ON
R/W
100 (0x64)
1~nDO
Enables the PWM for all
DO Channels
1
0 = Off
1 = On
(Default= 0)
R/W
127 (0x7F)
1
Restores all default web
settings
1
1 = Restore
W
128 (0x80)
1
Default ID Settings
1
1 = Restore
W
133 (0x85)
1
Reboots the ET-2200
module
1
1 = Restore
W
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
235 (0xEB)
1~nDO
Sets the Power-on value for
all DO Channels
1
0: OFF, 1: ON
(Default: 0)
R/W/F
267 (0x10B)
1~nDO
Sets the Safe value for all DO
Channels
1
0: OFF, 1: ON
(Default: 0)
R/W/F
“R”: Read, “W”: Write, “F”: Settings are recorded in flash by default,
“E”: After writing DO[60] register, the data will be stored in flash.
Note
For detail “DI/DO Modbus Address”information, refer to Section 6.3 Modbus Register Table
of user’s manual (http://ftp.icpdas.com/pub/cd/6000cd/napdos/et2200/document/).

Technical support: servic[email protected] P6
5 Configuring Network Settings
1) Run the eSearch Utility.
The eSearch Utility is located at:
http://ftp.icpdas.com/pub/cd/6000cd/napdos/software/esearch/
2) Click the “Search Servers”to search your ET-2268.
3) Double-click your ET-2268 to configure the settings
Factory Default Settings of ET-2268:
IP Address
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1
4) Contact your Network Administrator to obtain a correct network
configuration (such as IP/Mask/Gateway). Enter the network settings
and click “OK”. Note: The ET-2268 will use the new settings 2 seconds
later.





Technical support: servic[email protected] P7
6 Testing your Ethernet I/O Module
1) Wait 2 seconds and click “Search Servers”button again to ensure the
ET-2268 is working well with new configuration.
2) Click the name of ET-2268 to select it.
3) Click the “Web”button to log in to the web configuration pages.
(Or enter the URL address of the ET-2268 in the address bar of the
browser.)
4) Enter the password (default: Admin)in the “login password”field and
click “Submit”.



Use the default
password: Admin


Technical support: servic[email protected] P8
5) In the “Home”page allows a simple test to be performed to verify the Digital
Input and Output functionality.
6) In the “Digital I/O”section, click the “DO0”button to ON (Red).
7) Verify that the output LED status for “high”.



NO0 01
COM0 03
亮起