ICP DAS USA PM-3033 Series User manual

ICP DAS Co., LTD PM-3033 series Quick Start V1.10 Page 1
PM-3033 series Quick Start
1. Shipping Package
This shipping package contains the following items
1 x PM-3033 module 1 x Quick Start Screw Driver x 1 CD x 1
(This Document)
2. PM-3033 series introduction
ICP DAS brings the most powerful, cost-effective, advanced Smart Power Meters PM-3033 series that
gives you access to real-time electric usage for three-phase power measurement. With its high accuracy
(<0.5%, PF=1 ), the PM-3033 series can be applied to both low voltage primary side and/or medium/high
voltage secondary side and enables the users to obtain reliable and accurate energy consumption readings
from the monitored equipments in real time under operation.
Direct input from “secondary side 1A/5A” type CTs. Dedicated CTs are no longer needed, which lowers the
cost of implementation.
It operates over a wide input voltages range 10 ~ 500 VAC which allows worldwide compatibility. It also
supports Modbus RTU, Modbus TCP or CANopen protocols for easy integration.
2.1. Caution & Warning
The meter contains hazardous voltages, and should never be disassembled. Failing to follow
this practice will result in serious injury or death. Any work on or near energized meters,
meter sockets, or other metering equipment could induce a danger of electrical shock. It is
strongly recommended that all work should be performed only by qualified industrial
electricians and metering specialist. ICP DAS assumes no responsibility if your electrical installer does not follow
the appropriate national and local electrical codes.
ICP DAS assumes no liability for any damage resulting from the use of this product. ICP DAS reserves the right to
change this manual at any time without notice. The information furnished by ICP DAS is believed to be accurate
and reliable. However, no responsibility is assumed by ICP DAS for its use, not for any infringements of patents or
other rights of third parties resulting from its use.
2.2. Product Warranty & Customer Support
ICP DAS warrants all products free from defects in material and workmanship for a period of one year from the
date of shipping. During the warranty period, we will, at our position, either repair or replace any product that
proves to be defective. To report any defect, please contact ：[phone] or [e-mail].
2.2.1. Limitation of Warranty
This warranty does not apply to defects resulting from unauthorized modification, misuse, or use for reason other
than electrical power monitoring. The supplied meter is not a user-serviceable product.

ICP DAS Co., LTD PM-3033 series Quick Start V1.10 Page 2
3. Installation
Please use the soft dry clothes to clean the instrument.
Please do not use any chemical or detergent or volatile solvents to clean the instrument, in order to avoid any
possibility of the cover damage.
Dimension: 127mm（length）× 33mm（wide）× 100mm（high）
Please read this operation manual carefully before using.
Please re-confirm the measure position.
Reconfirm the RST (ABC) phase sequence of the power system.
PM-3033 series can be installed as rail mounting mode or embedded, no need to drill a hole or screw to fix it
(rail mounting width can up to the length of 35 mm).
Meter auxiliary power for PM-3033 series is DC +12V ~+48V.
3.1. Voltage Input
1. PM-3033 series: Input Voltage up to 500V.
For any higher Input Voltage large than 500V, please add the PT (power transformer), and Change PT RATIO
setup.
2. Confirm the RST (ABC) phase sequence.
3.2. Current Input
1. CT with secondary side output 1A/5A can be connected directly.
2. The current direction must follow K-L marked on CT’s.
800A/5A Primary CT Installation and Wiring

ICP DAS Co., LTD PM-3033 series Quick Start V1.10 Page 3
3.3. Connection
Please firstly check the current input terminal.
Make sure the arrow direction sign on Primary CT’s follows current flow direction（K→L）.
Note: it must be in the same direction.
Connect the voltage input terminal N C B A. for PM-3033 series, in the three phase order as
follows on N C B A.
Attention please!! For 3P3W-2CT, connect in N C A phase sequence, do not connect phase B
(Check the diagram).

ICP DAS Co., LTD PM-3033 series Quick Start V1.10 Page 4
Wiring
1P2W-1CT (PM-3033 series)
1P3W-2CT (PM-3033 series)
3P3W-2CT (PM-3033 series)

ICP DAS Co., LTD PM-3033 series Quick Start V1.10 Page 5
3P3W-3CT (PM-3033 series)
3P4W-3CT (PM-3033 series)
LED Indicator
The PM-3033 series has 2 LED to indicate the unit power status, communication, and
power data calculation.
RUN: Green, light up after communication ready. LED will flash when the unit is
processing communication.
PWR: Red, Power on LED always on.
3. Communication
RS-485 & CAN setting
Default setting for RS-485: 19200, n, 8, 1 ,for CAN:125K bps
DIP switch (SW1-SW6) is used for Modbus address(or CANopen Node
ID) setting, default is 1, i.e. all OFF
For example: Modbus address(or CANopen Node ID) is 10，find the
table of DIP switch 1-6 is ON, OFF, OFF, ON, OFF, OFF
SW1－SW6 setting
Setting Modbus-RTU address / CANopen Node ID for communication (1-64)

ICP DAS Co., LTD PM-3033 series Quick Start V1.10 Page 6
Modbus Address
( Node ID)
SW 1 SW 2 SW 3 SW 4 SW 5 SW 6
1
OFF
OFF
OFF
OFF
OFF
OFF
2
ON
OFF
OFF
OFF
OFF
OFF
3
OFF
ON
OFF
OFF
OFF
OFF
4
ON
ON
OFF
OFF
OFF
OFF
5
OFF
OFF
ON
OFF
OFF
OFF
6
ON
OFF
ON
OFF
OFF
OFF
7
OFF
ON
ON
OFF
OFF
OFF
8
ON
ON
ON
OFF
OFF
OFF
9
OFF
OFF
OFF
ON
OFF
OFF
10
ON
OFF
OFF
ON
OFF
OFF
11
OFF
ON
OFF
ON
OFF
OFF
12
ON
ON
OFF
ON
OFF
OFF
13
OFF
OFF
ON
ON
OFF
OFF
14
ON
OFF
ON
ON
OFF
OFF
15
OFF
ON
ON
ON
OFF
OFF
16
ON
ON
ON
ON
OFF
OFF
17
OFF
OFF
OFF
OFF
ON
OFF
18
ON
OFF
OFF
OFF
ON
OFF
19
OFF
ON
OFF
OFF
ON
OFF
20
ON
ON
OFF
OFF
ON
OFF
21
OFF
OFF
ON
OFF
ON
OFF
22
ON
OFF
ON
OFF
ON
OFF
23
OFF
ON
ON
OFF
ON
OFF
24
ON
ON
ON
OFF
ON
OFF
25
OFF
OFF
OFF
ON
ON
OFF
26
ON
OFF
OFF
ON
ON
OFF
27
OFF
ON
OFF
ON
ON
OFF
28
ON
ON
OFF
ON
ON
OFF
29
OFF
OFF
ON
ON
ON
OFF
30
ON
OFF
ON
ON
ON
OFF
31
OFF
ON
ON
ON
ON
OFF
32
ON
ON
ON
ON
ON
OFF
33
OFF
OFF
OFF
OFF
OFF
ON
34
ON
OFF
OFF
OFF
OFF
ON
35
OFF
ON
OFF
OFF
OFF
ON
36
ON
ON
OFF
OFF
OFF
ON
37
OFF
OFF
ON
OFF
OFF
ON
38
ON
OFF
ON
OFF
OFF
ON
39
OFF
ON
ON
OFF
OFF
ON
40
ON
ON
ON
OFF
OFF
ON
41
OFF
OFF
OFF
ON
OFF
ON
42
ON
OFF
OFF
ON
OFF
ON
43
OFF
ON
OFF
ON
OFF
ON
44
ON
ON
OFF
ON
OFF
ON
45
OFF
OFF
ON
ON
OFF
ON
46
ON
OFF
ON
ON
OFF
ON
47
OFF
ON
ON
ON
OFF
ON
48
ON
ON
ON
ON
OFF
ON
49
OFF
OFF
OFF
OFF
ON
ON
50
ON
OFF
OFF
OFF
ON
ON
51
OFF
ON
OFF
OFF
ON
ON

ICP DAS Co., LTD PM-3033 series Quick Start V1.10 Page 7
52
ON
ON
OFF
OFF
ON
ON
53
OFF
OFF
ON
OFF
ON
ON
54
ON
OFF
ON
OFF
ON
ON
55
OFF
ON
ON
OFF
ON
ON
56
ON
ON
ON
OFF
ON
ON
57
OFF
OFF
OFF
ON
ON
ON
58
ON
OFF
OFF
ON
ON
ON
59
OFF
ON
OFF
ON
ON
ON
60
ON
ON
OFF
ON
ON
ON
61
OFF
OFF
ON
ON
ON
ON
62
ON
OFF
ON
ON
ON
ON
63
OFF
ON
ON
ON
ON
ON
64
ON
ON
ON
ON
ON
ON
SW7
－
SW8 setting
PM-3033 series：For Baud Rate Setting
RS-485
CAN
SW 7
SW8
9600 bps
125k(Default) bps
OFF
OFF
19200 (Default) bps
250k bps
ON
OFF
38400 bps
500k bps
OFF
ON
115200 bps
1M bps
ON
ON
PM-3033 series：Select the different wiring mode
(Please select the Software setting, if 1P2W-1CT or 1P3W-2CT is used)
Models PM-3033/ PM-3033-CPS PM-3033-MTCP
Wiring SW 9 SW 10 SW 1 SW 2
Software setting
OFF
OFF
OFF
OFF
3P3W-2CT
ON
OFF
ON
OFF
3P3W-3CT
OFF
ON
OFF
ON
3P4W-3CT
ON
ON
ON
ON
Add the Bias Resistor on RS-485 Network for stable signal
The RS-485 master is required to provide the bias for PM-31xx series. Otherwise, the tM-SG4 or SG-785
should be added to provide the bias. All ICP DAS controllers and converters provide the bias.
Ethernet setting
Ethernet default settings:
IPAddress
192.168.255.1
Subnet mask 255.255.0.0
Gateway 192.168.0.1
Port 502

ICP DAS Co., LTD PM-3033 series Quick Start V1.10 Page 8
Specifications
Model PM-3033 PM-3033-MTCP PM-3033-CPS
AC Power Measurement
Wiring 1P2W-1CT, 1P3W-2CT, 3P3W-2CT, 3P3W-3CT and 3P4W-3CT
Measurement Voltage 10 ~ 500 V (CAT III)
Measurement Current Secondary current: 1A or 5A
Measurement Frequency 50-60 Hz
W Accuracy Better than 0.5% (PF:1)
Power Parameter
Measurement
True RMS voltage (Vrms), True RMS current (Irms), Active Power (kW), Active Energy (kWh),
Apparent Power (kVA), Apparent Energy (kVAh),
Reactive Power (kVAR), Reactive Energy (kVARh), Power Factor (PF),
Frequency(Hz)
Data Update Rate 1 Second
Communication
RS-485
Protocol Modbus-RTU -
Baud rate 9600,19200 (default), 38400, 115200;
DIP Switch Selectable
-
Data format
N,8,1 (default); N,8,2; E,8,1; E,8,2;
O,8,1; O,8,2
Isolation 3000 VDC -
Bias Resistor
No (Usually supplied by the RS-485
Master. Alternatively, add a tM-SG4
or SG-785)
Ethernet
Protocol - Modbus TCP
PoE - Yes, IEEE 802.3af
CANoepn
Protocol CANopen
Baud rate 125 k (default), 250 k, 500 k, 1 M;
Aux Power
Input Range +12 ~ 48 VDC
+12 ~ 48 VDC or PoE
+12 ~ 48 VDC
PoE Pin Assignments:
+ (Pin 1, 2), V- (Pin 3, 6)
Power Consumption 2 W
Dimensions (W x L x H) 127 mm x 100 mm x 33 mm
Environment
Operating Temperature -20 ~ +70 °C
Storage Temperature -25 ~ +80 °C