ICP DAS USA tSH-734 User manual

Technical support: [e-mail] P1
tSH-73x Series Quick Start
v1.0, Feb. 2018
What’s in the box?
Related Information
The package includes the following items:
tSH-73x Series
Module x1
Quick Start x1
(This Document)
CA-002 Cable x1
tSH Series Product Page:
Documentation & Firmware:
NS-205/NS-205PSE Product Page (optional):

Technical support: [e-mail] P2
1 Connecting the Power and Host PC
1) Make sure your PC has workable network settings.
Disable or well configure your Windows firewall andAnti-Virus firewall first,
else the “Search Servers” on Chapter 4 may not work. (Please contact
with your system Administrator)
2) Connect both the tSH-73x and your PC to the same sub network or the
same Ethernet switch.
3) Supply power (PoE or +12~+48 VDC)to the tSH-73x.

Technical support: [e-mail] P3
2 Installing Software on Your PC
Install eSearch Utility, which can be obtained from the web site:
http://ftp.icpdas.com/pub/cd/tinymodules/napdos/software/esearch/
3
Connecting the Master and Slave Devices
1) Connect the serial port of 2 PC (Master) to COM2/COM3 of the tSH-73x (e.g., tSH-734).
2) Connect the Modbus device (Slave, e.g., M-7022, optional) to COM1 on the
tSH-73x (e.g., tSH-734) .
3) Supply power (+10 ~+30 V
DC
) to the Modbus device (e.g., M-7022, Device ID: 1)
Note: The wiring and supply power method depends on your Modbus device.


Technical support: [e-mail] P4
4 Configuring Network Settings
1) Double click the eSearch Utility shortcut on the desktop.
2) Click the “Search Servers” button to search your tSH-73x.
3) Double click the name of tSH-73x to open the “Configure Server (UDP)”
dialog box.
Factory Default Settings of tSH-73x:
IP Address
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1
4) Contact your Network Administrator to obtain a correct network
configuration (such as IP/Mask/Gateway). Enter the network settings
and click “OK”. Note: The tSH-73x will use the new settings 2
seconds later.





Technical support: [e-mail] P5
5) Wait 2 seconds and click “Search Servers”button again to ensure the
tSH-73x is working well with new configuration.
6) Click the name of tSH-73x to select it.
7) Click the “Web”button to log in to the web configuration pages.
(Or enter the URL address of the tSH-73x in the address bar of the
browser.)
5 Configuring the Application Mode




Technical support: [e-mail] P6
1) Enter the password (use
the default password
“admin”) in the Login
password field and click
the “Submit”button.
2) Click the “Application Mode”tab to display the Application Mode
Settings page.
3) Check the “Mode 2: Modbus Sharer”option.
4) Select Port1 (since our M-7022 slave device is connected on this port)
from the “Slave Device Connected on:”option button.
5) Enter the timeout value of the Port1 (e.g. “500”)in the “Slave Timeout
(ms)”field and click the “Submit”button to save your settings.
Use the default
password: admin






Technical support: [e-mail] P7
6 Configuring the Serial Port
1) Click the “Port1”tab and select the appropriate Baud Rate and Data
Format settings depending on the M-7022 (Slave) from the relevant drop
down options. (e.g. Baud Rate: 115200 and Data Format: 8, None, 1)
2) Click the “Submit”button to save your settings.
3) Click the “Port2/Port3”tab and select the appropriate Baud Rate and
Data Format settings depending on the serial COM Port of PC (Master
#1/Master #2) from the relevant drop down options. (e.g. Baud Rate:
9600 and Data Format: 8, None, 1)
4) Click the “Submit”button to save your settings.





Technical support: [e-mail] P8
7 Self-Test
1) In the eSearch Utility, select
the “Modbus RTU Master”
item from the “Tools”menu to
open the Modbus RTU Master
Utility.
2) In the Modbus RTU Modbus Utility, select your COM port, Baud Rate and Data
Format (e.g. COM1/9600/N,8,1) on the PC (Master) and then click the “Open”
button in the “COM status”section.
3) Refer to “Protocol Description” section and type the command in the
“Command” field then click the “Send command” button. If the response data
is correct, it means the test is success.



Please ensure that the Timeout value in the
window should larger than 2 times the
Slave
timeout setting in the tSH-73x module.
The Modbus command settings
depends on your Modbus device.