ICP DAS USA I-7045 User manual

I-7045 16 Ch DO DAQ Module- QuickStart (May/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1
I-7045
16 Channel Digital Output Data Acquisition
Module
Quick Start Guide
Product Website:
https://www.icpdas-usa.com/i_7045_i_7045d.html
http://www.icpdas-usa.com/dcon_utility_pro.html
1. Introduction
I-7045 is intelligently designed to provide signal conditioning system
monitoring and safe value settings. I-7045 is a cost-effective solution for a
wide range of valuable industrial control signals and systems. The DCON
utility can help users to configure and test I-7045 16-Channel Isolated
Digital Output modules. Plenty of library functions and demo programs are
provided to let users develop programs easily under Windows, Linux and
DOS operating systems. Users may mount the modules on a DIN rail,
panel or wall. Modules have a screw-terminal block to connect to the
signals.
2. Terminal Assignment

I-7045 16 Ch DO DAQ Module- QuickStart (May/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
2
3. Block/ Wiring Diagram

I-7045 16 Ch DO DAQ Module- QuickStart (May/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3
4. Default Settings
Default settings for the I-7045 DIO modules are as follows:
。Module Address: 01
。DIO Type: Type 40
。Baud Rate: 9600 bps
。Checksum disabled
。J3 set to INIT mode enabled for I-7043/43D and
M-7043/43D.
5. Configuration
To install the module, follow the steps below:
1. Connect the analog output.
2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If
the host is only equipped with an RS-232 interface, then an RS-232 to RS-485
converter will be required.
3. Connect the module to the power supply using the +Vs and GND terminals. Note that
the voltage supplied should be in the range of +10 to +30V DC.

I-7045 16 Ch DO DAQ Module- QuickStart (May/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
4
4. Open DCON utility pro
click on COM port(first icon).
It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to
search module. The default settings for the module can be found in Section 3. Click OK
after selecting the COM port setting.

I-7045 16 Ch DO DAQ Module- QuickStart (May/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5
5. DCON utility pro will search for the selected COM port according the setting
previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS
and the others modules.

I-7045 16 Ch DO DAQ Module- QuickStart (May/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
6
6. Configuration I/O module setting on PC
7. For I-7000 modules, DCON utility pro terminal can send command to the module.
See user manual Sections 2 for details command.

I-7045 16 Ch DO DAQ Module- QuickStart (May/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
7
Configure the module: sending the %AANNTTCCFF command. See user manual
Section 2 for details.
Read data from the input channels: send either the #AA or #AAN command to the
module.
8. If user doesn’t know command, user can select Address and ID, it will show some
refer commands as below. User can select necessary command to test or debug
modules.