Icw Ultra 180 arm User manual

Page 1 ULTRA 180 & 182 ARM INSTALLATION - 6/29/20

Page 1 of 4

If Mounting to Ultra Wall Track

If Mounting to a Desk

• Drill a 3/8” hole through the horizontal

mounting surface.

• Screw stud into base of desk mount.

• Push the stud on the desk mount

through the hole.

• Slide the large mounting washer over

the stud from underneath.

• Add the 3/8 split-washer.

• Secure in place with the 3/8 nylock. Screw stud into

desk mount

Desk Desk

Washer Nylock

ATTACH ULTRA DESK MOUNT

ATTACH SLIDER TO ULTRA TRACK

• Insert slider into

wall track.

• Replace the

small socket

head cap

screw and

plastic cover.

Adjust slider to desired height. Tighten slider using adjustment knob.

ADJUST SLIDER POSITION

STANDARD INVERTED

Adjust slider to desired height. Tighten slider using adjustment knob.

ADJUST SLIDER POSITION

STANDARD INVERTED

ICW recommends

wood or metal stud

mounting only.

MAXIMUM LOAD CAPACITY: 32 LBS. (14.5 KG)

ULTRA 180 & 182 ARM INSTALLATION

• Drill a 3/8" hole thorugh the

horizontal mounting surface.

• Screw stud into base of desk mount.

• Push the stud on the desk mount

through the hole.

• Slide the large mounting washer

over the stud from underneath.

• Secure in place with 3/8" nylock nut.

Desk Mount

Part Number

Stud

Length

Maximum

Desk Thickness

D0 3.50” 2.47”

D1 3.50” 1.87”

D3 5.50” 1.87”

D5 7.50” 1.87”

D7 10.50” 2.38”

Screw stud

into desk mount

• Insert slider into wall track.

• Replace the plastic cover

and small socket

head cap screw.

Adjust slider to desired height. Tighten slider using adjustment knob.

ADJUST SLIDER POSITION

STANDARD INVERTED

Adjust slider to desired height. Tighten slider using adjustment knob.

ADJUST SLIDER POSITION

STANDARD INVERTED

Desk Desk

Washer

Nylock

• Remove small socket head cap screw in the top

center of the Wall Track. Remove plastic cover.

• Locate the wall stud and mark the top hole of the

Wall Track.

• Drill 11/64 pilot hole, insert #14 screw and tighten

slightly. Use a level, mark the lower holes, drill

pilot holes and then insert the #14 screws.

NOTE: #14 Wood screws are supplied with unit. If installing into

metal studs, you will need to replace these with proper metal

stud fasteners

MOUNT ULTRA TRACK TO WALL

• Remove small socket head cap screw in the top center of

the Wall Track. Remove plastic cover.

• Locate the wall stud and mark the top hole of the Wall Track.

• Drill 11/64 pilot hole, insert #14 screw and tighten slightly.

Use a level, mark the lower holes, drill pilot holes and then insert

the #14 screws.

NOTE: #14 wood screws are supplied with unit. If installing into metal

studs you will need to replace these with proper metal stud fasteners

or the provided snap togglers. All hardware used to secure track mount

must have a proper countersunk head.

ULTRA 180 & 182 ARM INSTALLATION - 6/29/20Page 2 of 4

If Mounting To A Wall

If Mounting to an MD Track

If Using EV65

Attach the

monitor mount

assembly to

the back of

your monitor,

using the

4mm screws

provided.

ATTACH VESA TO MONITOR

ULTRA 180 & 182 ARM INSTALLATION

If Mounting To A Pole

ICW recommends wood or metal stud mounting only.

W2 W3 W5

Use a level to be sure mount is correctly aligned.

• Install track as per MD track

installation.

• Loosely attach track adapters

to wall ear (W2, W3 or W5).

• Slide wall ear with loosely

attached track adapters into

MD track.

• Once in desired position,

tighten one track adapter

with 5/32 Allen wrench.

• Check to ensure wall ear is

level and tighten remainder

or track adapters.

MOUNT WALL PLATE TO MD TRACK

Attach the

monitor mount

assembly to

the back of

your monitor,

using the four

4mm screws

provided.

• Insert stubs on VESA plate

into holes in the Ergovision

joint assembly.

• Insert provided 5/16 x 3/4

socket cap screws in both

sides and tighten.

• Use the handle under

mount to loosen tilt friction

and adjust monitor tilt.

ATTACH VESA TO EV65 JOINT

Socket

cap screw

VESA

plate

ATTACH POLE CLAMP TO POLE

Using the 1/4″ hex

key, separate the

two halves of pole

mount as shown,

place around pole

at the desired height

and reassemble.

Locate the stud and mark

the top hole, drill 11/64

pilot hole and insert #14

screw and tighten slightly.

Using a level, mark the

lower hold and drill pilot

hole, insert #14 screw

and, with the unit level,

tighten both screws.

NOTE: ICW supplies #14

wood screws. If installing

onto metal studs, you will

need to replace with proper

metal stud fasteners.

ATTACH WALL PLATE TO WALL

ULTRA 180 & 182 ARM INSTALLATION - 6/29/20

ATTACH FLIP UP

• Remove screws from

drop extension using

5/32” hex key.

• Align holes in keyboard

tray with screw holes in

drop extension.

• Attach keyboard tray using

the provided screws.

• If keyboard will not remain in vertical

position, tighten two button head

screws underneath  ip up connector.

Page 3 of 4

If Using EV710

ULTRA 180 & 182 ARM INSTALLATION

If Attaching To Ultra Flip-Up

Ultra 180 & 182 Arm Cable Management

If Attaching To

Quick Disconnnect

Pivot tension adjustment screws

Slider

knob

RUN CABLES THROUGH ARM

• Cover plate is spring loaded. Loosen cover plate screws

on side of arm just enough to t cables through gap.

• Run cables loosely between cover plate and arm.

Cables can be run on either or both sides of the arm.

• Push cover plate against arm and tighten screws,

being careful not to pinch cables.

• After installing cable, pull cable back and forth a

couple inches to conrm cables are not pinched.

• Remove screws from

drop extension using

5/32” hex key.

• Align holes in keyboard

tray with screw holes

in drop extension.

• Attach keyboard tray

using the provided screws.

• If keyboard will not remain in vertical

position, tighten the two button head

screws underneath ip-up connector

to adjust the ip-up’s tension.

ATTACH FLIP-UP TRAY

MOUNT WALL PLATE TO WALL ADJUST BALL VESA HEIGHT & TENSION

• To adjust the height of

monitor, loosen slider

knob, position monitor

height on slider rails

then tighten knob.

• To adjust pivot tension,

gently and evenly

tighten or loosen the

four screws on the

back of the ball VESA.

• Mount VESA assembly

to slide rails.

• Fasten slider knob

through rails and into

VESA assembly.

• Attach VESA to

monitor using four

4mm screws in the

hardware bag

ATTACH QUICK DISCONNECT

• Remove beauty cap

on Quick Disconnect

block.

• Remove screw using

3/16” hex key.

• Slide keyboard tray

into Quick Disconnect

block.

• Replace screw and

tighten.

• Replace beauty cap.

Beauty cap

Screw

ULTRA 180 & 182 ARM INSTALLATION

ULTRA 180 & 182 ARM INSTALLATION - 6/29/20Page 4 of 4

Ultra Arm Cable Management

Adjusting Rotation Limits

Adjusting Arm Tension ADJUST ARM TENSION

Using the 3/16” T-handle

hex wrench provided, turn

the screw in the UL180/182

arm clockwise to lighten

the arm’s load resistance,

or counter-clockwise

to increase the load

resistance. The arm

must be horizontal

before adjusting.

IMPORTANT

Extend the UL180 or UL182 straight out and be

sure all equipment is mounted on the arm before

adjusting the arm’s resistance. Use the T-handle

provided to adjust the arms’ resistance. Do not

use power tools to adjust.

DO NOT ADJUST THE ARM TO SUPPORT

MORE THAN 32 LBS. DOING SO MAY

DAMAGE THE ARM.

Adjusting

rotation limits

for the standard

Ultra Arm

Place Stop Pins

as shown. The

Stop Pin is built into

the arm rather than

into the wall ear.

ULTRA CABLE MANAGEMENT

• Prepare all cables to route within the arm by placing them

near cavity of arm and bundling together if necessary.

• Remove cover by unscrewing four Phillips head cap screws.

Screws are captured by the cover so they cannot fall out.

Once screws are disengaged, pull cover out of arm.

• Place cables within the channel. Do not block the holes

where screws will engage in arm.

• Replace cover and tighten screws. Cables should be

able to pull through to desired position if necessary.

NOTICE: ICWUSA.COM, Inc. provides the appropriate hardware fasteners to match the majority if not all standard monitors and devices. It is the responsibility of

the installer / integrator to ensure that the screws and fasteners have the adequate thread engagement. The rule of thumb is that the thread depth is greater than the

diameter of the hole or 4 full turns of 360 degrees of thread engagement. It is also the responsibility of the installer / integrator to ensure that they do not damage the