ICW TITAN ELITE T2EQ-C8X5 User manual

TITAN ELITE EASY-TO-WIRE CEILING MOUNT INSTALLATION - rev 09/01/16 pjm
If you have any questions please call Toll Free 1-800-558-4435
ICWUSA.com, Inc.
TITAN ELITE CEILING MOUNT INsTALLATION
Page 1 of 3
DO NOT use power tools to assemble or
adjust the arm. Use hand tools ONLY.
IMPORTANT
MAXIMUM LOAD CAPACITY:
28 LBS (12.7 KG)
•Do not attempt to adjust the arm until all components
are mounted (monitor, keyboard, etc.)
•Arm must be completely horizontal (extended)
before adjusting the arm’s tension. Failure to do so will
damage the arm and void the warranty.
•NEVER loosen or remove any of the shoulder
bolts. Doing so will cause the arm to immediately
come apart with tremendous force, and could cause
serious injury.
• If equipment requiring AC power is mounted to this unit,
haveacertiedelectricianinspecttheinstallation.
• Failure to install this unit according to these instructions
will void all ICW warranties. If installed incorrectly, ICW
is not liable for any damage or injury caused by the unit.
The Elite arm contains high pressure gas
springs. The following cautions MUST be
observed to avoid serious injury.
DANGER!
MOUNT sQUARE CEILING PLATE
Loosen the set screw
in ceiling plate before
attaching extension pipe.
Using four 1/4 x 2” lag bolts
provided in hardware bag,
secure ceiling plate to a solid
wood surface or ceiling joist.
Use square pattern or inline
pattern. Be sure to use all four
bolts.
Run wires through center hole
or wire management port.
Loosen set screw BEFORE
attaching pipe. Screw
extension pipe into ceiling
plate, then tighten set screw.
Wire management holes
MOUNT INLINE CEILING PLATE
Loosen the set screw
in ceiling plate before
attaching extension pipe.
Firmly secure ceiling mount
to solid ceiling joist using
four #14 wood screws found
in hardware bag. Be sure
mount is level.
Loosen set screw BEFORE
attaching pipe. Screw
extension pipe into ceiling
plate, then tighten set screw.
T2EQ-C8X5
Improved cable management.
Wires run through the joints
and are more enclosed.
Thread arm onto extension pipe
andtighten.AFTERarmisrmly
attached, tighten set screw with
5/32 hex key.
DO NOT loosen lower, smaller screw
without instructions from ICW.
ATTACH ARM TO EXTENsION PIPE
Set
screw

TITAN ELITE EASY-TO-WIRE CEILING MOUNT INSTALLATION - rev 09/01/16 pjm
TITAN ELITE CEILING MOUNT INsTALLATION
Page 2 of 3
ADJUsT QUICKLINK TILT
QuickLink
buttons
Pivots
Use the under-monitor handle
to rotate, tilt and swivel the
monitor to desired position.
Increase range of motion by
depressing buttons on back
of QuickLink. Each button
provides 90° of adjustment
for its corresponding pivot.
Depressing both buttons
at once provides 180° of
adjustment.
REMOVE ELITE ARM COVERs
END COVERS
Remove the end covers by
unscrewing the two 3/4” long
10-24atheadscrewsusinga
Phillips head screwdriver.
TOP COVER
Remove the long arm cover
by unscrewing the two 1/4”
long6-32atheadscrewsin
the center of the cover using
a Phillips head screwdriver. If
you use a power tool, be very
careful not to strip the screws.
The arm needs to be in a
vertical position to remove the
long top cover.
Cord Management
REMOVE TITAN ARM CAPs
Remove plastic caps
that cover the wire ports
on the Titan section of
the arm.
ATTACH QUICKLINK TO ARM
9/16 wrench
Nut
Remove nut from bolt
on QuickLink. Attach
QuickLink to arm. Thread
nut onto bolt through front
of arm assembly. Tighten
bolt with provided 9/16”
wrench.
ATTACH VEsA AND HANDLE TO MONITOR
Using a Phillips
screw driver, attach
the VESA plate
to the back of the
monitor using four
4mm screws in the
hardware bag.
Attach handle to
VESA plate.
Torque Chart- In/lbs 2/23/2016
Minimum torque values Monitor Mount
Arm
Base
Mount Arm Joint Paralink EV710 Ultra
021-021-021etilE
021-021021021etilE2T
Titan (T2) 120 120 120 - 120
02158021021021artlU
UL180 / UL182 120 120 - 85 -
MD Arm 140 - 120 - 120

TITAN ELITE CEILING MOUNT INsTALLATION
TITAN ELITE EASY-TO-WIRE CEILING MOUNT INSTALLATION - rev 09/01/16 pjm
Page 3 of 3
REPLACE TITAN ARM CAPs
Replace the caps on both
ends of the Titan arm.
REPLACE ARM COVERs
Before reattaching arm
covers, slip wires through
end cover port.
Reattach black plastic
bushing around exiting
wires.
Replace covers on the Elite section of the arm.
DO NOT use a power tool to replace screws.
ADJUsT ARM REsIsTANCE
Extend the arm
straight out as shown
before adjusting the arm’s
resistance. Be sure all equipment
is mounted on the arm before
adjusting. Use the T-handle provided
to adjust the arm’s resistance.
DO NOT USE POWER TOOLS TO ADJUST.
FEED WIRE THROUGH TITAN ARM
Pull wires one at a time
through the arm. Feed the
largestwirerst,allowing
enough slack so the arm
turns freely.
Feedtherstwirethrough
the extension pipe and down
throughtherstjointandoutof
therstwireport.
Feed the wire back up through
the Titan arm and out through
the second wire port, then
down to the Elite section of
the arm.
Repeat these steps with the
second wire. Wires run through
the joints.
RUN WIREs THROUGH CHANNEL OF ELITE ARM
After feeding the wires through
the Titan (upper) section of
the arm, press them into the
channels of the Elite (lower)
section.
Use wire clips to secure them.
Be sure wires don’t bind
and the arm moves freely.
Wire clip
ADJUsT ROTATION sTOPs
Rotation limits for the
arm are set by placing
stop pins in the holes
where you want the
arm to stop. The stop
pins can be removed
and set by hand.
Rotation
Limiter Ring
Stop Pin