ICW W2 User manual

LAPTOP TRAY ARM INSTALLATION
• Remove small socket head cap screw in the top
center of the Wall Track. Remove plastic cover.
• Locate the wall stud and mark the top hole of the
Wall Track.
• Drill 11/64 pilot hole, insert #14 screw and tighten
slightly. Use a level, mark the lower holes, drill
pilot holes and then insert the #14 screws.
NOTE: #14 Wood screws are supplied with unit. If installing into
metal studs, you will need to replace these with proper metal
stud fasteners
MOUNT ULTRA TRACK TO WALL
LAPTOP TRAY ARM INSTALLATION - 6/1/20
IF MOUNTING
TO THE WALL
IF MOUNTING TO THE
ULTRA WALL TRACK
ATTACH ARM TO MOUNT MANAGE CABLES
Follow instructions below
for your style of mount.
Follow instructions
on next page. IMPORTANT: DO NOT ip up tray when laptop is placed on it.
ATTACH QUICK DISCONNECT
• Remove beauty cap on
Quick Disconnect block.
• Remove screw using
3/16” hex key.
• Slide keyboard tray into
Quick Disconnect block.
• Replace screw and
tighten.
• Replace beauty cap.
LAPTOP TRAY ARM INSTALLATION
MOUNT ULTRA TRACK TO WALL
• Remove small socket head cap screw in the top center
of the Wall Track. Remove plastic cover.
• Locate the wall stud and mark the top hole of the Wall Track.
• Drill 11/64 pilot hole, insert #14 screw and tighten slightly. Use a level,
mark the lower holes, drill pilot holes and then insert the #14 screws.
NOTE: #14 wood screws are supplied with unit. If installing into metal studs you will
need to replace these with proper metal stud fasteners or the provided snap togglers.
All hardware used to secure track mount must have a proper countersunk head.
Beauty cap
Screw
ATTACH SLIDER TO ULTRA TRACK
• Insert slider into wall track.
• Replace the plastic cover
and small socket
head cap screw.
Once you have adjusted the
slider to the desired height,
tighen down the Track Slider
using the knob on the slider
as shown.
Adjust slider to desired height. Tighten slider using adjustment knob.
ADJUST SLIDER POSITION
STANDARD INVERTED
ATTACH WALL PLATE TO WALL
W2
Locate the stud and mark
the top hole, drill 11/64
pilot hole and insert #14
screw and tighten slightly.
Using a level, mark the
lower hold and drill pilot
hole, insert #14 screw
and, with the unit level,
tighten both screws.
NOTE: ICW supplies
#14 wood screws. If
installing onto metal
studs, you will need
to replace with proper
metal stud fasteners.
W3

LAPTOP TRAY ARM INSTALLATION
LAPTOP TRAY ARM INSTALLATION - 6/1/20
IF MOUNTING TO A DESK
IF MOUNTING
TO A POLE
WARNING: Provided hook-and-loop fastener strips are intended to hold laptop in place when tray is level. They are NOT intended to secure the laptop
when tray is ipped up into stowed position. CAUTION: Heat generated by some laptops may soften the glue of the hook-and-loop fasteners.
Screw stud
into desk mount
ATTACH POLE CLAMP TO POLE
Using the 1/4″ hex key,
separate the two halves of
pole mount as shown, place
around pole at the desired
height and reassemble.
ULTRA CORD MANAGEMENT
1. Prepare all cables to route within the arm by placing them
near cavity of arm and bundling together if necessary.
2. Remove cover by unscrewing four screws.
Screws are captured by the cover so they cannot fall out.
Once screws are disengaged, pull cover out of arm.
3. Place cables within the channel. Do not block
the holes where screws will engage in arm.
4. Replace cover and tighten screws. Cables should be
able to pull through to desired position if necessary.
Desk Mount
Part Number
Stud
Length
Maximum
Desk Thickness
D0 3.50” 2.47”
D1 3.50” 1.87”
D3 5.50” 1.87”
D5 7.50” 1.87”
D7 10.50” 2.38”
Drill a 3/8 hole through the horizontal mounting
surface. Push the All Thread bolt on desk mount
assembly through the hole in the horizontal surface.
Slide large mounting washer over the bolt from
underneath and secure in place with 3/8 nylock nut.
NOTICE: ICWUSA.COM, Inc. provides the appropriate hardware fasteners to
match the majority if not all standard monitors and devices. It is the responsibility
of the installer / integrator to ensure that the screws and fasteners have the
adequate thread engagement. The rule of thumb is that the thread depth is
greater than the diameter of the hole or 4 full turns of 360 degrees of thread
engagement. It is also the responsibility of the installer / integrator to ensure that
they do not damage the monitor or device by using a screw or fastener that is too
long for hole and therefore damaging the unit by inserting too far.
When cleaning your ICW mounting unit please follow the points below. Proper
cleaning of the mounting device will help assure proper function and extend the
life of the unit.
1. Any general cleaner is acceptable except degreasers are not recommended near
the bearing entrances.
2. Spray cleaner or water on a soft cloth or paper towel and then wipe down
the mounts.
3. Do not spray directly at the bearing seams (located at all swivel points) as this could
reduce the life of the bearings.
CLEANING OF THE ICW MOUNTING DEVICE
Desk Desk
Washer
Nylock
ULTRA CORD MANAGEMENT