ICW ULTRA UL180 User manual

Page 1 ULTRA 180 & 182 ARM INSTALLATION - rev 11/22/17 Page 1 of 4
• Remove small socket head cap screw in top
center of the Wall Track. Remove plastic cover.
• Locate the wall stud and mark the top hole
of the Wall Track.
• Drill 11/64 pilot hole, insert #14 screw and
tighten slightly. Use a level, mark the lower
holes, drill pilot holes and then insert the
#14 screws.
NOTE: #14 Wood screws are supplied with unit. If installing into metal studs, you will need to
replace these with proper metal stud fasteners
MOUNT ULTRA TRACK TO WALL
If Mounting to Ultra Wall Track
If Mounting to a Desk
• Drill a 3/8” hole through the horizontal
mounting surface.
• Screw stud into base of desk mount.
• Push the stud on the desk mount
through the hole.
• Slide the large mounting washer over
the stud from underneath.
• Add the 3/8 split-washer.
• Secure in place with the 3/8 nylock. Screw stud into
desk mount
Desk Desk
Washer Nylock
ATTACH ULTRA DESK MOUNT
ATTACH SLIDER TO ULTRA TRACK
• Insert slider into
wall track.
• Replace the
small socket
head cap
screw and
plastic cover.
Adjust slider to desired height. Tighten slider using adjustment knob.
ADJUST SLIDER POSITION
STANDARD INVERTED
ICW recommends wood or
metal stud mounting only.
MAXUMUM LOAD CAPACITY: 32 LBS. (14.5 KG)
ULTRA, UL180 & UL182 ARM INSTALLATION
• Drill a 3/8" hole thorugh the
horizontal mounting surface.
• Screw stud into base of desk mount.
• Push the stud on the desk mount
through the hole.
• Slide the large mounting washer
over the stud from underneath.
• Secure in place with 3/8” nylock nut.
• Insert slider
into wall track.
• Replace the
plastic cover
and small
socket head
cap screw.
Desk Mount
Part Number
Stud
Length
Maximum
Desk Thickness
D0 3.50” 2.47”
D1 3.50” 1.87”
D3 5.50” 1.87”
D5 7.50” 1.87”
D7 10.50” 2.38”

ULTRA 180 & 182 ARM INSTALLATION - rev 11/22/17Page 2 of 4
If Mounting To A Wall
If Mounting to an MD Track
If Using EV65
Attach the
monitor mount
assembly to
the back of
your monitor,
using the
4mm screws
provided.
ATTACH VESA TO MONITOR
ULTRA, UL180 & UL182 ARM INSTALLATION
If Mounting To A Pole
• Using the 1/4” hex key,
separate the two halves
of pole mount as shown.
• Place around pole at
the desired height and
reassemble.
ATTACH POLE CLAMP TO POLE
Socket
cap screw
VESA
plate
• Insert stubs on VESA plate
into holes in the Ergovision
joint assembly.
• Insert provided 5/16 x 3/4
socket cap screws
in both sides
and tighten.
• Use the handle
under mount to
loosen tilt friction and
adjust monitor tilt.
ATTACH VESA TO EV65 JOINT
ICW recommends wood or metal stud mounting only.
• Locate the wall stud and mark
top hole for wall mount.
• Drill 11/64” pilot hole. Insert #14
screw and tighten slightly.
• Using a level, mark the lower
hole(s) and drill pilot hole(s).
• Insert #14 screw(s) and, with the
unit level, tighten all screws.
NOTE: ICW supplies #14 wood screws. If
installing onto metal studs, you will need to
replace with proper metal stud fasteners.
MOUNT WALL PLATE TO WALL
W2
Use a level
to be sure
mount is
correctly
aligned.
W3
W2 W3
Use a level to be sure mount is correctly aligned.
• Install track as per MD track installation.
• Loosely attach track adapters
to wall ear (W2 or W3).
• Slide wall ear with loosely attached
track adapters into MD track.
• Once in desired position, tighten one
track adapter with 5/32 Allen wrench.
• Check to ensure wall ear is level and
tighten remainder or track adapters.
MOUNT WALL PLATE TO MD TRACK
Attach the
monitor mount
assembly to
the back of
your monitor,
using the four
4mm screws
provided.

ULTRA 180 & 182 ARM INSTALLATION - rev 11/22/17
ATTACH FLIP UP
• Remove screws from
drop extension using
5/32” hex key.
• Align holes in keyboard
tray with screw holes in
drop extension.
• Attach keyboard tray using
the provided screws.
• If keyboard will not remain in vertical
position, tighten two button head
screwsunderneathipupconnector.
Page 3 of 4
If Using EV710
ULTRA, UL180 & UL182 ARM INSTALLATION
If Attaching To Ultra Flip-Up
Ultra 180 & 182 Arm Cable Management
If Attaching To
Quick Disconnnect
ADJUST BALL VESA HEIGHT & TENSION
• To adjust the height of
monitor, loosen slider
knob, position monitor
height on slider rails,
then tighten knob.
• To adjust pivot tension,
gently and evenly
tighten or loosen the
four screws on the back
of the ball VESA.
Pivot tension
adjustment screws
Slider
knob
ATTACH QUICK DISCONNECT
• Remove beauty cap
on Quick Disconnect
block.
• Remove screw using
3/16” hex key.
• Slide keyboard tray
into Quick Disconnect
block.
• Replace screw and
tighten.
• Replace beauty cap.
Beauty cap
Screw
RUN CABLES THROUGH ARM
• Cover plate is spring loaded. Loosen cover plate screws
onsideofarmjustenoughtotcablesthroughgap.
• Run cables loosely between cover plate and arm.
Cables can be run on either or both sides of the arm.
• Push cover plate against arm and
tighten screws, being careful
not to pinch cables.
STORE CABLE INSIDE COVER PLATE
Extra cable can be looped inside the cover plate to provide
a neater appearance and simplify cleaning.
• Mount VESA
assembly to
slide rails.
• Screw slider knob
through rails and
into VESA assembly.
• Attach VESA to
monitor using four
4mm screws in the
hardware bag.
MOUNT VESA TO SLIDE RAILS, ATTACH MONITOR
• Mount VESA
assembly to
slide rails.
• Fasten slider knob
through rails and
into VESA assembly.
• Attach VESA to
monitor using four
4mm screws in
the hardware bag.
• Remove screws from
drop extension using
5/32” hex key.
• Align holes in keyboard
tray with screw holes
in drop extension.
• Attach keyboard tray
using the provided screws.
• If keyboard will not remain in vertical
position, tighten the two button head
screwsunderneathip-upconnector
toadjusttheip-up’stension.
ATTACH FLIP-UP TRAY

ULTRA, UL180 & UL182 ARM INSTALLATION
ULTRA 180 & 182 ARM INSTALLATION - rev 11/22/17Page 4 of 4
Ultra Arm Cable Management
Adjusting Rotation Limits
Adjusting Arm Tension ADJUST ARM TENSION
Using the 3/16” T-handle
hex wrench provided, turn
the screw in the UL180/182
arm clockwise to lighten
thearm’sloadresistance,
or counter-clockwise
to increase the load
resistance. The arm
must be horizontal
before adjusting.
IMPORTANT
Extend the UL180 or UL182 straight out and be
sure all equipment is mounted on the arm before
adjusting the arm’s resistance. Use the T-handle
provided to adjust the arms’ resistance. Do not
use power tools to adjust.
DO NOT ADJUST THE ARM TO SUPPORT
MORE THAN 32 LBS. DOING SO MAY
DAMAGE THE ARM.
Adjusting
rotation limits
for the standard
Ultra Arm
Place Stop Pins
as shown. The
Stop Pin is built into
the arm rather than
into the wall ear.
ULTRA CABLE MANAGEMENT
• Prepare all cables to route within the arm by placing them
near cavity of arm and bundling together if necessary.
• Remove cover by unscrewing four Phillips head cap screws.
Screws are captured by the cover so they cannot fall out.
Once screws are disengaged, pull cover out of arm.
• Place cables within the channel. Do not block the holes
where screws will engage in arm.
• Replace cover and tighten screws. Cables should be
able to pull through to desired position if necessary.